Contact Details Please note that some of the contact details on this PDF document may not be current. Please use the following details if you need to contact us: Telephone: 0844 879 3588 Email:
[email protected] The customer support section of our website also features a wide range of information which may be of use to you and is available 24 hours a day. It includes: • Operating and installation instructions • Easy ‘How to use’ guides for storage heaters • Service and repairs • Where to buy our products • Literature downloads • Heating requirement calculator Visit ‐ www.dimplex.co.uk/support A division of GDC Group Ltd Millbrook House Grange Drive Hedge End Southampton SO30 2DF www.dimplex.co.uk
Registered No: 1313016 England VAT GB 287 1315 50004 EEE Producer Registration Number – WEE/GE0057TS Paper from sustainable sources
Installation Instructions STORAGE HEATER SHELF FITTING INSTRUCTIONS Models: SHE6, SHE12, SHE18, SHE24 83977 Issue 10 : 05.09 CONTENTS
TOOLS REQUIRED
1 x Shelf 2 x Wall Brackets, 1 Left Hand & 1 Right Hand 4 x No. 6 x 3/8” Self-tapping screws 4 x Fibre Rawl Plugs 4 x No. 10 x 2” Fixing Screws 1 x Flexible Seal
Pozi-drive Screwdriver Suitable Drill
ASSEMBLY OF SHELF 1
Lay the main shelf body face down on a smooth surface to prevent damage to the paint finish.
2
Take one of the end brackets, position as shown in Fig. 1, ensuring the “lip” of the end bracket is underneath the “lip” of the shelf body.
3
Using a pozi-drive screwdriver, fix the end bracket to the shelf body with two of the No. 6 x 3/8” self tapping screws provided in the fixing kit.
4
Repeat procedures 2 and 3 for the remaining end bracket.
5
Peel off the back of the sealing strip, if necessary trimming to size, and attach to the back of the shelf as shown in fig. 2.
FIG.1
FIG.2
6
Position the shelf centrally above the heater so that the bottom edge of the shelf is at least 150mm above the top surface of the heater. Check that the shelf is level and mark the positions of the four screw holes on the wall, refer to fig. 3.
MARK POSITION
MINIMUM 150MM
FIG.3
7
Taking care to prevent dust entering the heater drill the four holes, insert the rawl plugs and fix the shelf to the wall using the four fixing screws provided. If the walls are panelled type please use suitable fixings.
Warning - If an alternative shelf (wooden, shelf with longer overhang) is to be used then it must be located 250mm above the top surface of the heater.
NOTE: CXL/S12N and CXL/S18N MODELS ONLY WHEN MOUNTING AN ALTERNATIVE SHELF THE FOLLOWING APPLIES: If an alternative shelf other than the Dimplex SHE is installed closer to the top surface of the CXL/S12 or the CXL/S18 than 250mm, but no less than 150mm, then de-rating of the convector element is required. Move the brown wire as indicated in Fig. 4 to the empty terminal as shown in Fig. 5.
Mauve
Empty Brown
Fig. 4 - before de-rating Model
Brown Wire still in circuit (upper element)
Mauve Wire still in circuit (lower element)
Mauve
Fig. 5 - after de-rating
Both in circuit
CXL/S12N
450W
450W
900W
CXL/S18N
450W
1000W
1450W
Dimplex UK Limited, Millbrook House, Grange Drive, Hedge End, Southampton, SO30 2DF.
Brown
Tel: Fax: Web-site
© GDC Group Ltd. All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing. A division of the GDC Group Ltd, Millbrook House, Grange Drive, Hedge End, Southampton SO30 2DF
0845 600 5111 01489 773 050 www.dimplex.co.uk
