ITB # DASPS-1111-15 Attachment A Specifications
Region 1 - Midwest Oregon Specification
Courts Security Systems Upgrades Oregon judicial Department October 27, 2014
Court Facilities
Courts Security Systems Upgrades Oregon judicial Department
Benton County Courthouse Lincoln County Courthouse Linn County Courthouse Marion County Courthouse Marion County Court Annex Marion County Juvenile Center (Old) Marion County Juvenile Center (New) Polk County Courthouse Yamhill County Courthouse
Project Regions
Courts Security Systems Upgrades Oregon judicial Department
Region 1 – Midwest Oregon Courts Security Systems Upgrades Oregon Judicial Department Dept of Admin Services
Construction Documents Specification October 27, 2014
PREPARED BY Hennebery Eddy Architects, Inc. 921 SW Washington, Suite 250 Portland, OR 97205 503.227.4860 phone 503.227.4920 fax
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 000110 TABLE OF CONTENTS PROCUREMENT AND CONTRACTING REQUIREMENTS 1.01 Division 00 – Procurement and Contracting Requirements A.
000110 – Table of Contents
B.
005000 – Contracting Forms and Supplements
SPECIFICATIONS 2.01 Division 01 – General Requirements A.
011000 – Summary
B.
012200 – Unit Prices
C.
012600 – Contract Modifications Procedures
D.
013000 – Administrative Requirements
E.
013591 – Historic Treatment Procedures
F.
016000 – Product Requirements
G. 017000 – Execution and Closeout Requirements H.
017419 – Construction Waste Management and Disposal
2.02 Division 02 – Existing Conditions A.
024100 – Demolition
2.03 Division 03 – Concrete (Not Used) 2.04 Division 04 – Masonry (Not Used) 2.05 Division 05 – Metals (Not Used) 2.06 Division 06 – Wood, Plastics, and Composites (Not Used) 2.07 Division 07 – Thermal and Moisture Protection A.
078400 – Firestopping
2.08 Division 08 – Openings A.
087100 – Door Hardware
B.
087101 – Hardware Groups
2.09 Division 09 – Finishes A.
099000 – Paint and Coatings
2.10 Division 10 – Specialties (Not Used) Region 1 – Midwest Oregon Courts Security Systems Upgrades
TABLE OF CONTENTS 000110 1
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
2.11 Division 11 – Equipment (Not Used) 2.12 Division 12 – Furnishings (Not Used) 2.15 Division 21 – Fire Suppression (Not Used) 2.16 Division 22 – Plumbing (Not Used) 2.17 Division 23 – Heating, Ventilating, and Air-Conditioning [HVAC] (Not Used) 2.18 Division 26 – Electrical A.
260501 – Electrical Demolition
B.
260505 – General Electrical Requirements
C.
260519 – Building Wire and Cable
D.
260534 – Conduit
E.
260535 – Surface Raceways
F.
260537 – Boxes
2.19 Division 27 – Communications A.
271005 – Low-Voltage Cabling Pathways
2.20 Division 28 – Electronic Safety and Security A.
281300 – Access Control
B.
281600 – Duress System
C.
282300 – Video Surveillance
END OF TABLE OF CONTENTS 000110
Region 1 – Midwest Oregon Courts Security Systems Upgrades
TABLE OF CONTENTS 000110 2
PROJECT DIRECTORY Courts Security Systems Upgrades Oregon Judicial Department Dept. of Admin. Services HEA Project No. 10013
OWNER
ARCHITECT
Oregon Judicial Department Supreme Court Building 1163 State Street Salem, OR 97301-2563 Evan West 503.986.4647 phone 503.986.5401 fax
[email protected]
Hennebery Eddy Architects, Inc. 921 SW Washington, Suite 250 Portland, OR 97205 Randall Rieks 503.227.4860 phone 503.227.4920 fax
OWNER'S PROJECT MANAGER
ELECTRICAL ENGINEER & SECURITY SPECIALIST
Department of Admin Services Facilities Division 1225 Ferry Street SE, U 100 Salem, OR 97301 Nicholas Larson 503.373.7196 phone 503.378.4947 fax
[email protected]
[email protected]
971-200-7242 direct
MKE & Associates, Inc. 6915 SW Macadam Ave., Ste200 Portland, OR 97219 Paul Berry 503.892.1188 phone 503.892.1190 fax
[email protected]
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 005000 CONTRACTING FORMS AND SUPPLEMENTS PART 1 GENERAL 1.01 Contractor is responsible for obtaining a valid license to use all copyrighted documents specified but not included in the Project Manual. 1.02 AGREEMENT AND CONDITIONS OF THE CONTRACT A.
See State of Oregon Invitation to Bid for the Agreement forms to be executed.
B.
See State of Oregon General Conditions For Public Improvement Contracts for the General Conditions.
C.
See State of Oregon General Conditions For Public Improvement Contracts for the Supplementary Conditions.
1.03 FORMS A.
Use the following forms for the specified purposes unless otherwise indicated elsewhere in the Contract Documents.
B.
Post-Award Certificates and Other Forms: 1. Submittal Transmittal Form: AIA G810. 2. Schedule of Values Form: AIA G703. 3. Application for Payment Form: AIA G702 and G703.
C.
Clarification and Modification Forms: 1. Request for Information Form: by Contractor 2. Substitution Request Form (During the Bidding/Negotiating Stage): CSI Form 1.5C 3. Architectural Supplemental Instruction Form: by Owner's Authorized Representative. 4. Construction Change Directive Form: by Owner's Authorized Representative. 5. Request for Proposal Form: by Owner's Authorized Representative. 6. Change Order Request Form: by Contractor. 7. Change Order Form: by Owner.
D.
Closeout Forms: 1. Certificate of Substantial Completion Form: by Owner.
1.04 REFERENCE STANDARDS A.
AIA G702 - Application and Certificate for Payment; 1992.
B.
AIA G703 - Continuation Sheet; 1992.
C.
AIA G810 - Transmittal Letter; 2001.
PART 2 PRODUCTS - NOT USED PART 3 EXECUTION - NOT USED END OF SECTION Region 1 - Midwest Oregon Courts Security Systems Upgrades
CONTRACTING FORMS AND SUPPLEMENTS 005000 1
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 011000 SUMMARY PART 1 GENERAL 1.01 PROJECT A.
Project Name: Region 1 - Midwest Oregon Courts Security Systems Upgrades.
B.
Owner's Name: Oregon Judicial Department.
C.
Owner's Project Manager: Oregon Department of Administrative Services Facilities Division.
D.
Owner's Authorized Representative's Name: Hennebery Eddy Architects, Inc.
E.
Building Owner: County in Region
1.02 DESCRIPTION OF WORK COVERED BY CONTRACT DOCUMENTS A.
Project Description 1. The scope of this project is to improve the security of the appellate, tax and circuit courts of the state and the Office of the State Court Administrator (OSCA). It includes three security measures: access control, video surveillance, and duress system. a. Access control is focused on providing controlled access to perimeter doors entering directly into the spaces primarily used by the courts personnel. b. Video surveillance is focused on providing visual monitoring of courtrooms, currency/payment areas and courtroom support areas related to family law desk/window, restraining order desk, and treatment courts. c. Duress system is focused on providing emergency signaling to an identified agency from the judge's bench and judicial assistant station in the courtrooms as well as their offices, the security room/desk and currency/payment counter areas and courtroom support areas. 2. The State is divided into five (5) geographic regions to manage the work effort. The projects will be implemented by region, starting in Region 5 and proceeding through Regions 4A, 4B, 3, 2, and 1. 3. The scope of work for this package is for Region 1 ONLY.
B.
Scope of demolition and removal work is to be determined by the Contractor in its entirety as required to accommodate the installation of the new work shown on drawings and specified in Section 024100.
C.
Scope of work is shown on drawings.
D.
Region 1 - Midwest Oregon 1. Benton County Courthouse – National Historic Register a. Access Control 1) Existing access control system requires no upgrades. Provided as prescribed by the contract documents. b. Video Surveillance 1) Existing video surveillance requires upgrades. Provided as prescribed by the
Region 1 - Midwest Oregon Courts Security Systems Upgrades
SUMMARY 011000 1
DAS Contract Number R02331 HEA Job Number 10013
2.
3.
4.
5.
6.
27 October 2014 Construction Documents
contract documents. c. Duress System 1) Existing duress system requires upgrades. Provided as prescribed by the contract documents. Lincoln County Courthouse a. Access Control 1) Existing access control system to remain. No work on this system. b. Video Surveillance 1) Existing video surveillance requires upgrades. County furnished, County Installed. c. Duress System 1) Existing duress system requires upgrades. County furnished, County installed. Linn County Courthouse a. Access Control 1) The facility is not currently equipped with an access control system. Provided as prescribed by the contract documents. b. Video Surveillance 1) Existing video surveillance requires upgrades. Provided as prescribed by the contract documents. c. Duress System 1) Existing duress system requires upgrades. Provided as prescribed by the contract documents. Marion County Courthouse a. Access Control 1) Existing access control system requires upgrades. Provided as prescribed by the contract documents. b. Video Surveillance 1) Existing video surveillance requires no upgrades. Provided as prescribed by the contract documents. c. Duress System 1) Existing duress system to remain. No work on this system. Marion County Court Annex a. Access Control 1) Existing access control system requires upgrades. Provided as prescribed by the contract documents. b. Video Surveillance 1) Existing video surveillance requires upgrades. Provided as prescribed by the contract documents. c. Duress System 1) Existing duress system requires upgrades. County furnished, County installed. Marion County Juvenile Center (Old) a. Access Control 1) Existing access control system requires upgrades. Provided as prescribed by the contract documents.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
SUMMARY 011000 2
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
b.
7.
8.
9.
Video Surveillance 1) Existing video surveillance requires upgrades. Provided as prescribed by the contract documents. c. Duress System 1) Existing duress system requires upgrades. County furnished, County installed. Marion County Juvenile Center (New) a. Access Control 1) Existing access control system requires upgrades. Provided as prescribed by the contract documents. b. Video Surveillance 1) Existing video surveillance requires upgrades. Provided as prescribed by the contract documents. c. Duress System 1) Existing duress system to remain. No work on this system. Polk County Courthouse – Eligible for National Historic Register a. Access Control 1) Existing access control system requires upgrades. Provided as prescribed by the contract documents. b. Video Surveillance 1) Existing video surveillance requires upgrades. Provided as prescribed by the contract documents. c. Duress System 1) Existing duress system requires upgrades. Provided as prescribed by the contract documents. Yamhill County Courthouse a. Access Control 1) Existing access control system requires upgrades. Provided as prescribed by the contract documents. b. Video Surveillance 1) Existing video surveillance requires upgrades. Provided as prescribed by the contract documents. c. Duress System 1) Existing duress system requires upgrades. Provided as prescribed by the contract documents.
1.03 WORK SEQUENCE A.
See State of Oregon General Conditions for Public Improvement Contracts – Schedule of Work, for project schedule procedures. 1. The selected Contractor for each region will divide the Region's facilities into the following groups. The contractor will be required to complete each group through final punchlist before starting construction on the next group in order to keep the construction duration reasonable for each group and/or facility. 2.
Contractor to provide a detailed project schedule as described in Section H.2.1 – SCHEDULE OF WORK in the State of Oregon General Conditions for Public Improvement
Region 1 - Midwest Oregon Courts Security Systems Upgrades
SUMMARY 011000 3
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
Contracts. 3.
Region 1 Facilities: a. Group 1: South Benton County Courthouse Lincoln County Courthouse Linn County Courthouse b. Group 2: North Polk County Courthouse Yamhill County Courthouse c. Group 3: Central Marion County Court Annex Marion County Juvenile (Old and New) Marion County Courthouse
1.04 WORK BY OWNER A.
Concurrently with Work of this Contract: 1. Any project distributing building materials due to demolition or renovation activities requires an asbestos material survey before processing. Samples will be taken of materials suspected of containing asbestos by the Owner's Environmental Services Consultant during the pre-construction site visit tour. It is the responsibility of the prime contractor to take the lead on deciding which materials might be impacted by the scope of work and cooperating with the Environmental Services Consultant to minimize the impact to hazardous materials (i.e. asbestos, lead) as much as possible by finding suitable cable routing and equipment installation locations. a. Removal or encapsulation of any known asbestos and removal of any known hazardous materials will be the responsibility of the contractor as it relates to the project scope and be negotiated primarily as a Change Order to the Contract. Coordinate any and all abatement work with the Owner's material survey before proceeding. See the State of Oregon General Conditions for further requirements of the hazardous materials abatement subcontractor. All inquiries relative thereto shall be directed to the Owner's Project Manager. Hennebery Eddy Architects, Inc. and its consultants bear no responsibility either directly or implied relating to this aspect of the work. 2. As Work progresses and upon at least 2 weeks advance notice by Contractor, removal of existing small equipment and tenants items, which may interfere with Contractor's Work.
1.05 BUILDING OWNER OCCUPANCY A.
Building Owner will occupy premises during Contract Period for the conduct of Building Owner's normal operations.
B.
Cooperate with Building Owner during construction operations to minimize conflicts and to facilitate Building Owner's use of facilities.
C.
Schedule Work to maintain Building Owner's continuous operations. Include in Contract Price sufficient funds as may be required for any "overtime" work caused by this
Region 1 - Midwest Oregon Courts Security Systems Upgrades
SUMMARY 011000 4
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
requirement. No additional payment to Contractor and Sub-Contractors will be authorized because of Contractor's and Sub-Contractors failure to anticipate required "overtime" work. 1.06 CONTRACTOR USE OF SITE AND PREMISES A.
Arrange use of site and premises to allow: 1. Building Owner occupancy. 2. Work by Others. 3. Work by Owner. 4. Use of site and premises by the public.
B.
Coordinate use of premises as directed by Owner.
C.
Contractor shall instruct Subcontractors, vendors, and their employees to enter building only through existing building entry where designated by Building Owner. Do not use other entries.
D.
Contractor shall conduct his operations as to insure the least reasonable inconvenience to the general public.
E.
Provide access to and from site as required by law and by Building Owner: 1. Emergency Building Exits During Construction: Keep all exits required by code open during construction period; provide temporary exit signs if exit routes are temporarily altered. 2. Do not obstruct roadways, sidewalks, or other public ways without permit.
F.
Existing building spaces may not be used for storage of materials or equipment.
G. Obtain and pay for any necessary additional storage or work areas at no additional cost to Owner. H.
If and where necessary and when directed, move any stored products, equipment, or vehicles which are under Contractor's control, and which interfere with operations of Owner or separate Contractor.
I.
In addition to the requirements stated elsewhere in this section, and the Supplemental General Conditions, the following requirements regarding Contractor's use of premises are known items requiring special coordination with the Owner and Owner's Project Manager. The Supplemental General Conditions outlines the Contractor's allowable work hours; however, this section provides some exceptions. These are items provided for the Contractor's convenience but do not necessarily represent all of the coordination requirements: 1. Courtrooms, Judge's Chambers, Judicial Assistant's offices, Jury Rooms.
J.
Time Restrictions: 1. Limit conduct of especially noisy exterior work to the hours of weekends and or outside of normal business hours. 2. Limit conduct of especially noisy interior work to the hours of weekends and or outside of normal business hours.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
SUMMARY 011000 5
DAS Contract Number R02331 HEA Job Number 10013
K.
27 October 2014 Construction Documents
Utility Outages and Shutdown: 1. Limit disruption of utility services to hours the building is unoccupied. 2. Prevent accidental disruption of utility services to other facilities.
1.07 OVERTIME WORK A.
To permit arrangements for inspections, the Contractor shall notify the Owner's Authorized Representative at least 48 hours in advance of any overtime work, including nights, weekends, and holidays. Do no overtime work, requiring inspections, without notifying Owner's Project Manager.
B.
The Contractor shall reimburse the Owner and Owner's Project Manager for any expenses incurred by them because of Contractor's overtime work.
1.08 PROTECTING EXISTING UTILITIES A.
Contractor shall assume that unknown utility lines do exist, and Contractor shall proceed with caution when working in areas that could conceal unknown utilities. If such utility lines are encountered, immediately request disposition instructions from Owner's Project Manager.
B.
If utility lines are damaged, remove, repair, or replace lines as directed. Additional compensation and/or extensions of time, if any, caused by removing, repairing, or replacing lines will be determined in accordance with General Conditions.
1.09 PROTECTING BUILDING AND BUILDING OCCUPANTS A.
Contractor shall prevent exposing building occupants to dust, debris, excessive noise, excessively high or low air temperatures, unpleasant odors, corridor obstructions, etc.
B.
Contractor shall provide adequate protection, as judged by the Owner, of building occupant work areas from dust and debris.
C.
Flooring finishes shall be protected from construction debris.
1.10 USE OF BUILDING OWNER'S PROPERTY & EQUIPMENT A.
Do not use Building Owner's property, facilities, or equipment such as tools, ladders, furniture, janitorial equipment, supplies, etc.
1.11 EXCESSIVE NOISE A.
Do not make excessive noise, such as that caused by jack hammers, air compressors, electricity generators, rivet guns, other similar devices, or any other source that will be disruptive to Building Owner's business activities, during Building Owner's normal working hours 6:00 am to 5:30 pm.
B.
When such noise is unavoidable, notify Owner's Project Manager at least 48 hours prior to such noise, comply with Owner's instructions, and limit noise duration to 2 hours maximum in any 1 day.
C.
Workers shall not play radios or other similar devices anywhere on site.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
SUMMARY 011000 6
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
1.12 OFFENSIVE ODORS A.
Smoking is prohibited within existing building.
B.
Do not use offensive smelling compounds, including adhesives, roofing asphalt, paints, sealers, etc. When such odors are unavoidable, exhaust odors directly to out-of-doors.
1.13 FIRE-HAZARDOUS WORK A.
Perform no welding, torch-cutting, soldering, brazing, or other hazardous work which could activate existing fire or smoke detectors without the following: 1. Give Owner's Project Manager 48 hours advance notice of such work. 2. Maintain adequate fire extinguishing equipment close at hand during such work.
1.14 SHUTDOWN OF EXISTING UTILITIES A.
Limit disruption of utility services to hours the building is unoccupied.
B.
Do not disrupt or shut down life safety systems, including but not limited to fire sprinklers and fire alarm system, without 10 days notice to Building Owner and authorities having jurisdiction.
C.
Do not interrupt existing utility services without advance written approval of Owner's Project manager.
D.
Minimum Advance Notice for Electric Service: 1. For all interruptions: 10 working days
E.
Minimum Advance Notice for All Other Services: 1. For minor interruptions: 5 working days 2. For major interruptions impacting entire building or floor: 10 working days
F.
Prevent accidental disruption of utility services to other facilities.
1.15 RESPONSE TIME FOR CORRECTING NON-COMPLYING WORK A.
Contractor's response to notice of Work to be corrected shall be accomplished during the following time periods: 1. Emergency Work: a. Failures or deficiencies constituting immediate danger or health hazard to people or likely damage to property. b. Response time: 24 hours per day 7 days per week 2. Urgent Work: a. Failures or deficiencies which do not immediately endanger persons or property, but would soon do so if not corrected. b. Response time: Between 7:00 AM & 4:00 PM on Mondays thru Fridays and within 3 calendar days following receipt of notice. 3. Routine Work: a. Failures or deficiencies of less importance that do not meet criteria of emergency or urgent work. b. Response time: Between 7:00 AM & 4:00 PM on Mondays thru Fridays and within 5 calendar days following receipt of notice.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
SUMMARY 011000 7
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
1.16 SPECIAL INSPECTIONS A.
Coordinating, scheduling, and employing the special inspection company shall be the responsibility of the Contractor.
B.
Copies of the inspection results shall be forwarded to the Owner's Project Manager and Owner's Authorized Representative.
1.17 WORK SEQUENCE A.
Coordinate construction schedule and operations with Owner, Owners Project Manager and Building Owner.
PART 2 PRODUCTS - NOT USED PART 3 EXECUTION - NOT USED END OF SECTION
Region 1 - Midwest Oregon Courts Security Systems Upgrades
SUMMARY 011000 8
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 012200 UNIT PRICES PART 1 GENERAL 1.01 SECTION INCLUDES A.
List of unit prices, for use in preparing Bids.
1.02 COSTS INCLUDED A.
Unit Prices shall include full compensation for all required products, tools, equipment, plant, transportation, services and incidentals; erection, programming, application or installation or removal of an item of the Work; overhead and profit. 1. Prices will be added or deducted from the Contract Sum by appropriate modification, if the scope of Work or estimated quantities of Work required by the Contract Documents are increased or decreased.
B.
Assume scope shown on the equipment schedule for inclusion in base bid as described in the section Base Bid Allocations, below. Also include a schedule of unit prices, for items listed below.
C.
Adjustments, based on actual quantities and unit prices, for items listed below, will be handled in the form of a Change Order.
1.03 MEASUREMENT OF QUANTITIES A.
Take all measurements and compute quantities. Measurements and quantities will be verified by Owner's Authorized Representative.
B.
Assist by providing necessary equipment, workers, and survey personnel as required.
C.
Perform surveys required to determine quantities, including control surveys to establish measurement reference lines. Notify Owner's Authorized Representative prior to starting work.
D.
Contractor's Engineer Responsibilities: Sign surveyor's field notes or keep duplicate field notes, calculate and certify quantities for payment purposes.
1.04 PAYMENT A.
Payment for Work governed by unit prices will be made on the basis of the actual measurements and quantities of Work that is incorporated in or made necessary by the Work and accepted by the Owner's Authorized Representative, multiplied by the unit price.
B.
Payment will not be made for any of the following: 1. Products wasted or disposed of in a manner that is not acceptable. 2. Products determined as unacceptable before or after placement. 3. Products not completely unloaded from the transporting vehicle. 4. Products placed beyond the lines and levels of the required Work. 5. Products remaining on hand after completion of the Work. 6. Loading, hauling, and disposing of rejected Products.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
UNIT PRICES 012200 1
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
1.05 SCHEDULE OF UNIT PRICES A. Items: 1. Add/deduct one (1) mortise lockset. 2. Add/deduct one (1) cylindrical lockset - heavy duty. 3. Add/deduct one (1) surface mounted closer - heavy duty. 4. Add/deduct complete access control to one door, including card reader, request to exit device, door position switch, electric strike and associated wiring. Assume wire run from door to controller is 250 feet or less, conduit or surface raceway will not be required, and that a spare door control position is available in the access control system. 5. Add/deduct complete access control to one door, including card reader, request to exit device, door position switch, electric mortise lock, associated wiring, power supply, 120 volt power, Assume wire run from door to controller is 250 feet or less, conduit or surface raceway will not be required, and that a spare door control position is available in the access control system. 6. Add/deduct complete access control to one door, including card reader, request to exit device, door position switch, electromagnetic lock, associated wiring, power supply, 120 volt power, Assume wire run from door to controller is 250 feet or less, conduit or surface raceway will not be required, and that a spare door control position is available in the access control system. 7. Add/deduct one (1) megapixel IP Camera, including dome, mounting accessories, Category 6 wiring. 8. Add/deduct one (1) 768 x 494 resolution Day/Night Analog Camera including dome, mounting accessories, Category 6 wiring. 9. Add/deduct one (1) 8 channel NVR, including required accessories, 20 amp dedicated 120 volt circuit, UPS, and training. 10. Add/deduct one 16 channel NVR, including required accessories, 20 amp dedicated circuit, UPS, and training. 11. Add/deduct one (1) 32 channel NVR, including required accessories, 20 amp dedicated circuit, UPS, and training. 12. Add/deduct one (1) 8 port 1000Mbps POE network switch including connections. 13. Add/deduct one (1) Category 6 single port outlet including junction box, jack, faceplate, cable termination and testing. Assume existing patch panel is available, and assume an average wire run of 250 feet of cable. 14. Add/deduct one (1) 24 port Category 6 patch panel. 15. Add/deduct one (1) 4 port digital video encoder, programming, and low voltage connections. 16. Add/deduct one (1) complete hard wired duress button include associated wiring, accessories. Assume an average wire run length of 250 feet. 17. Add/deduct one (1) complete wireless duress button and associated receiver, and wiring of receiver. 18. Add/deduct one (1) complete keypad/annunciator include associated wiring, accessories. Assume an average wire run length of 250 feet. 19. Add/deduct 100 feet of access control, duress keypad or duress button wiring. To be added or deleted for very long or short wire runs associated with applicable unit costs Region 1 - Midwest Oregon Courts Security Systems Upgrades
UNIT PRICES 012200 2
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
for devices listed above. Assume wiring will be concealed and conduit or surface raceway will not be required. 1.06 BASE BID ALLOCATIONS A.
Base Bid will be ALL devices included on the equipment schedules; unit prices will be added or deducted change orders per the General Conditions.
PART 2 PRODUCTS - NOT USED PART 3 EXECUTION - NOT USED END OF SECTION
Region 1 - Midwest Oregon Courts Security Systems Upgrades
UNIT PRICES 012200 3
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 012600 CONTRACT MODIFICATION PROCEDURES PART
1
GENERAL
1.01
RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 1 Specification Sections, apply to this Section.
1.02
SUMMARY A. This Section specifies administrative and procedural requirements for handling and processing Contract modifications.
1.03
REQUESTS FOR INFORMATION A. It is the responsibility of the Contractor to promptly and no later than five (5) days from the date the Contractor and/or Subcontractor knew or should have known to notify the Owner's Project Team by RFI of any deviations and conflicts, unforeseen site conditions and conflicts, additional permit requirements, code required changes and to request clarification prior to initiating any such related work. No additional payment, consideration for claim, dispute or relief of liquidated damages will be made to the Contractor for failure to promptly notify Owner's Project Team of any issues and promptly provide detailed information on the impacts of cost and/or schedule. B. All Request for Information (“RFI”) clarifications by the Contractor shall be in submitted in writing, numbered, clearly identify the issue by location, referenced drawings sheet or specification, propose a solution, estimated cost and estimated schedule impact and desired timeline for response. C. The Owner's Project Team upon receipt of a RFI will make an initial determination if the request is complete, valid and determine the appropriate method of response. All Owners' Project Team responses will be in writing to the Contractor. A RFI log will be maintained by the Contractor and reviewed with the Owner's Project Team at the construction meetings. D. Except for emergency actions, the Contractor may not proceed with any specific work or related work until the Owner's Project Team responds to the RFI. If the Contractor takes any action or proceeds with any work without clarification or authorization; all work and related work may be subject to rejection by the Owner's Project Team with no subsequent adjustment to Contract performance schedule, cost or liquidated damages.
Region 1 – Midwest Oregon Courts Security Systems Upgrades
CONTRACT MODIFICATIONS PROCEDURES 012600- 1
DAS Contract Number R02331 HEA Job Number 10013
1.04
27 October 2014 Construction Documents
MINOR CHANGES IN SCOPE OF WORK A. When necessary, Owner's Project Team will issue supplemental instructions authorizing Minor Changes in the Work, not involving adjustment to either the Contract Price or the Contract Time. All supplemental instructions will be made in writing and may include but not limited to Architectural Supplemental Instructions (“ASI”) or Construction Change (Field) Directives (“CCD”). B. If the Contractor disagrees with the Owner's Project Team determination on Contract Price and/or Contract Time, the Contractor may request reconsideration under the General Conditions Disputes and Claims Process.
1.05
REQUESTS FOR PROPOSAL A. Owner-Initiated Change Proposal Requests: When appropriate, Owner's Project Team will issue a detailed description of proposed changes in the Work and request that the Contractor submit a proposal that may require adjustment to the Contract. If necessary the description will accompanied by supplemental or revised Drawings and/or Specifications. B. Requests For Proposal are not actionable until authorized in written form by either a Construction Change Directive or a Change Order by the Owner's Project Team. C. Unless otherwise specified, within five (5) days after receipt of Requests For Proposal, Contractor shall submit a Change Order Request proposal estimating cost adjustments to the Contract Sum and the Contract Time necessary to execute the change as follows: 1. Include a list of quantities of products required or eliminated and unit costs, with total amount of purchases and credits to be made. If requested, furnish survey data to substantiate quantities. 2. Indicate applicable taxes, delivery charges, equipment rental, and profit and overhead. Submitted total shall represent total reimbursement required by Contractor for the additional work. 3. Include an updated Contractor's Construction Schedule that indicates the effect of the change. D. Contractor-Initiated Change Proposal Requests: The Contractor may propose changes to the Contract by submitting a written Change Order Request proposal to the Owner's Project Team. At minimum each request shall: 1. Include a statement outlining reasons for the change and the effect of the change on the Work. Provide a complete description of the proposed change. Indicate the effect of the proposed change on the Contract Sum and/or the Contract Time.
Region 1 – Midwest Oregon Courts Security Systems Upgrades
CONTRACT MODIFICATIONS PROCEDURES 012600- 2
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
2. Include a list of quantities of products required or eliminated and unit costs, with total amount of purchases and credits to be made. If requested, furnish survey data to substantiate quantities. 3. Indicate applicable taxes, delivery charges, equipment rental, and profit and overhead. Submitted total shall represent total reimbursement required by the Contractor for the additional work. 4. Include an updated Contractor's Construction Schedule that indicates the effect of the change E. The Owner's Project Team upon receipt of a Change Order Request proposal will make an initial determination if the request is complete, valid and determine the appropriate method of response. All Owners' Project Team responses will be in writing to the Contractor. F. Except for emergency actions, the Contractor may not proceed with any specific work or related work until the Owner's Project Team responds to the Change Order Request proposal. If the Contractor takes any action or proceeds with any work without clarification or authorization; all work and related work may be subject to rejection by the Owner's Project Team. If the Contractor takes any action or proceeds with any work without clarification or authorization; all work and related work may be subject to rejection by the Owner's Project Team with no subsequent adjustment to Contract performance schedule, cost or liquidated damages. G. Pursuant to the General Conditions the Owner's Project Team may accept the Contractors Change Order Request proposal, reject the Contractors Change Order Request proposal and/or negotiate the terms of the Contractors Change Order Request proposal. 1.06
CONSTRUCTION CHANGE (FIELD) DIRECTIVE A. The Owner's Project Team, to facilitate the construction schedule and completion of the work may authorize a written Construction Change (Field) Directive delivered by fax, by e-mail or by hand to the Contractor. A Construction Change (Field) Directive will provide a detailed description of the change in the scope of Work, and will designate a method by which to determine the cost of either the Work or the performance Time. If no actual lump sum cost was previously agreed to between the Owner's Project Team and the Contractor, a basis for payment and Not-toExceed amount will be established. Contractor shall then not exceed the amount authorized without subsequent approval and direction from Owner's Project Team. B. Written Construction Change (Field) Directives will subsequently be followed with a Written Change Order to the Contract in accordance with the General Conditions.
Region 1 – Midwest Oregon Courts Security Systems Upgrades
CONTRACT MODIFICATIONS PROCEDURES 012600- 3
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
C. In urgent or emergency situations the Owner's Project Team may authorize verbal Construction Change (Field) Directives to the Contractor in the field which will subsequently be followed by a Written Construction Change (Field) Directive to the Contractor. Contractor shall immediately notify the Owner's Project Team if they disagree with any provision of the Construction Change (Field) Directive. PART 2 PRODUCTS (not applicable) PART 3 EXECUTION (not applicable) END OF SECTION
Region 1 – Midwest Oregon Courts Security Systems Upgrades
CONTRACT MODIFICATIONS PROCEDURES 012600- 4
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 013000 ADMINISTRATIVE REQUIREMENTS PART 1 GENERAL 1.01 SECTION INCLUDES A.
Preconstruction meeting.
B.
Progress meetings.
C.
Progress photographs.
1.02 RELATED REQUIREMENTS A.
See State of Oregon General Conditions for Public Improvement Contracts - Schedule of Work, for project schedule procedures.
B.
Section 017000 - Execution and Closeout Requirements: Additional coordination requirements.
C.
See State of Oregon General Conditions for Public Improvement Contracts - Submittals, Shop Drawings, Product Data and Samples, for project submittals for review.
PART 2 PRODUCTS - NOT USED PART 3 EXECUTION 3.01 PRECONSTRUCTION MEETING A.
Owner's Project Manager will schedule a meeting after Notice of Award.
B.
Attendance Required: 1. Owner. 2. Owner's Project Manager. 3. Owner's Authorized Representative. 4. Contractor.
C.
Agenda at a minimum will include: 1. Execution of Owner-Contractor Agreement. 2. Submission of executed bonds and insurance certificates. 3. Distribution of Contract Documents. 4. Submission of list of Subcontractors, list of Products, schedule of values, and progress schedule. 5. Designation of personnel representing the parties to Contract, and Owner's Authorized Representative. 6. Procedures and processing of field decisions, submittals, substitutions, applications for payments, proposal request, Change Orders, and Contract closeout procedures. 7. Scheduling.
D.
Record minutes and distribute copies within two days after meeting to participants, with two copies to Owner's Project Manager, Owner's Authorized Representative, Owner, Building Owner, participants, and those affected by decisions made.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
ADMINISTRATIVE REQUIREMENTS 013000 1
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
3.02 PROGRESS MEETINGS A.
Schedule and administer phone conference meetings throughout progress of the Work at maximum two week intervals.
B.
Make arrangements for meetings, prepare agenda with copies for participants, and preside at meetings.
C.
Attendance Required: Job superintendent, major Subcontractors and suppliers, Owner, Owner's Project Manager, Owner's Authorized Representative, Building Owner as appropriate to agenda topics for each meeting.
D.
Agenda may include at a minimum: 1. Review minutes of previous meetings. 2. Review of Work progress. 3. Field observations, problems, and decisions. 4. Identification of problems that impede, or will impede, planned progress. 5. Review of submittals schedule and status of submittals. 6. Review of off-site fabrication and delivery schedules. 7. Maintenance of progress schedule. 8. Corrective measures to regain projected schedules. 9. Planned progress during succeeding work period. 10. Coordination of projected progress. 11. Maintenance of quality and work standards. 12. Effect of proposed changes on progress schedule and coordination. 13. Other business relating to Work.
E.
Record minutes and distribute copies within two days after meeting to participants, with two copies to Owner's Authorized Representative, Owner, Building Owner, participants, and those affected by decisions made.
3.03 PROGRESS PHOTOGRAPHS A.
Submit photographs before each progress meeting, taken not more than 3 days prior to meeting.
B.
Submit photographs with each application for payment, taken not more than 3 days prior to submission of application for payment.
C.
Photography Type: Digital; electronic files.
D.
Provide photographs of staging and construction throughout progress of Work produced by an experienced photographer, acceptable to Owner's Project Manager.
E.
In addition to periodic, recurring views, take photographs of each of the following events: 1. Final completion, minimum of ten (10) photos.
F.
Take photographs as evidence of existing project conditions deemed unexpected.
G. Views: 1. Photographs will be non-human, facility specific items. General overview shots will not be taken and are not allowed. Region 1 - Midwest Oregon Courts Security Systems Upgrades
ADMINISTRATIVE REQUIREMENTS 013000 2
DAS Contract Number R02331 HEA Job Number 10013
2. 3. H.
27 October 2014 Construction Documents
Provide correct exposure and focus, high resolution and sharpness, maximum depth of field, and minimum distortion. Point of View Sketch: Provide sketch identifying point of view of each photograph if requested by Owner's Project Manager. Digital Photographs: 24 bit color, minimum resolution of 1024 by 768, in JPG or PDF format; provide files unaltered by photo editing software. 1. Delivery Medium: via Email or Contractor's FTP site. 2. File Naming: Include project identification, date and time of view, and view identification. 3. Point of View Sketch: Include digital copy of point of view sketch when requested to clarify photograph location. 4. Hard Copy: Printed hardcopy (grayscale) of PDF file and point of view sketch.
3.04 NUMBER OF COPIES OF SUBMITTALS A.
Documents: Submit one electronic copy in PDF format; an electronically-marked up file will be returned. Create PDFs at native size and right-side up; illegible files will be rejected. 1. Owner's Authorized Representative may request that all of the Documents for Review or a portion of them be submitted in Hard Copy format. a. Documents for Review: 1) Small Size Sheets, Not Larger than 8-1/2 x 11 inches: Submit the number of copies that Contractor requires, plus two copies that will be retained by Owner's Authorized Representative. 2) Larger Sheets, Not Larger than 36 x 48 inches: Submit the number of opaque reproductions that Contractor requires, plus two copies that will be retained by Owner's Authorized Representative.
3.05 SUBMITTAL PROCEDURES A.
Transmit each submittal with AIA Form G810 or approved form.
B.
Sequentially number the transmittal form. Revise submittals with original number and a sequential alphabetic suffix.
C.
Identify Project, Contractor, Subcontractor or supplier; pertinent drawing and detail number, and specification section number, as appropriate on each copy.
D.
Apply Contractor's stamp, signed or initialed certifying that review, approval, verification of Products required, field dimensions, adjacent construction Work, and coordination of information is in accordance with the requirements of the Work and Contract Documents.
E.
Deliver submittals to Owner's Authorized Representative at business address.
F.
Schedule submittals to expedite the Project, and coordinate submission of related items.
G. For each submittal for review, allow 10 days excluding delivery time to and from the Contractor. H.
Identify variations from Contract Documents and Product or system limitations that may be detrimental to successful performance of the completed Work.
I.
Provide space for Contractor and Owner's Authorized Representative review stamps.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
ADMINISTRATIVE REQUIREMENTS 013000 3
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
J.
When revised for resubmission, identify all changes made since previous submission.
K.
Distribute reviewed submittals as appropriate. Instruct parties to promptly report any inability to comply with requirements.
L.
Submittals not requested will not be recognized or processed.
END OF SECTION
Region 1 - Midwest Oregon Courts Security Systems Upgrades
ADMINISTRATIVE REQUIREMENTS 013000 4
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 013591 HISTORIC TREATMENT PROCEDURES PART 1 GENERAL 1.01
SECTION INCLUDES A. General protection and historic treatment procedures for work in spaces, areas, rooms, and surfaces in a designated historic building on the National Historic Register or as part of a National Historic District as well as a building with historic character not yet designated a historic building or as part of a National Historic District.
1.02
RELATED REQUIREMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply to this Section. B. Regulatory Requirements: Comply with notification regulations of authorities having jurisdiction before beginning removal and dismantling work. Comply with hauling and disposal regulations of authorities having jurisdiction. C. Section 011000 – Summary: Designated historic buildings and districts or buildings eligible for historic designation.
1.03
DEFINITIONS A. Consolidate: To strengthen loose or deteriorated materials in place. B. Dismantle: To disassemble and detach items by hand from existing construction to the limits indicated, using small hand tools and small one-hand power tools, so as to protect nearby historic surfaces; and legally dispose of dismantled items off-site, unless indicated to be salvaged or reinstalled. C. Existing to Remain: Existing items that are not to be removed or dismantled. D. Match: To blend with adjacent construction and manifest no apparent difference in material type, species, cut, form, detail, color, grain, texture, or finish; as approved by Architect. E. Reconstruct: To remove existing item, replicate damaged or missing components, and reinstall in original position. F. Reinstall: To protect removed or dismantled item, repair and clean it as indicated for reuse, and reinstall it in original position, or where indicated. G. Remove: Specifically for historic spaces, areas, rooms, and surfaces, the term means to detach an item from existing construction to the limits indicated, using hand tools and hand-operated power equipment, and legally dispose of it off-site, unless indicated to be salvaged or reinstalled. H. Repair: To correct damage and defects, retaining existing materials, features, and finishes while employing as little new material as possible. Includes patching, piecing-in, splicing, consolidating, or otherwise reinforcing or upgrading materials.
Region 1 – Midwest Oregon Courts Security Systems Upgrades
HISTORIC TREATMENT PROCEDURES 013591 1
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
I.
Replace: To remove, duplicate, and reinstall entire item with new material. The original item is the pattern for creating duplicates unless otherwise indicated.
J.
Replicate: To reproduce in exact detail, materials, and finish unless otherwise indicated.
K. Reproduce: To fabricate a new item, accurate in detail to the original, and in either the same or a similar material as the original, unless otherwise indicated. L. Restore: To consolidate, replicate, reproduce, repair, and refinish as required to achieve the indicated results. M. Retain: To keep existing items that are not to be removed or dismantled. N. Reversible: New construction work, treatments, or processes that can be removed or undone in the future without damaging historic materials unless otherwise indicated. O. Salvage: To protect removed or dismantled items and deliver them to Owner ready for reuse. P. Stabilize: To provide structural reinforcement of unsafe or deteriorated items while maintaining the essential form as it exists at present; also, to reestablish a weather-resistant enclosure. Q. Strip: To remove existing finish down to base material unless otherwise indicated. 1.03
MATERIALS OWNERSHIP A. Historic items, similar objects and other items of interest or value to Building Owner that may be encountered during removal and dismantling work remain Building Owner's property. Carefully dismantle and salvage each item or object.
1.04
REFERENCE STANDARDS A. ANSI/ASSE A10.6
1.06
QUALITY ASSURANCE A. Field Supervisor Qualifications: Full-time supervisors experienced in historic treatment work similar in nature, material, design, and extent to that indicated for this Project. B. Worker Qualification: Persons who are experienced in historic treatment work of types they will be performing.
1.07
STORAGE AND PROTECTION OF HISTORIC MATERIALS A. Existing Historic Materials to Remain: Protect construction indicated to remain against damage and soiling from construction work. Where permitted by Building Owner, items may be dismantled and taken to a suitable, protected storage location during construction work and reinstalled in their original locations after historic treatment and construction work in the vicinity is complete.
Region 1 – Midwest Oregon Courts Security Systems Upgrades
HISTORIC TREATMENT PROCEDURES 013591 2
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
B. Storage and Protection: When taken from their existing locations, catalog and store historic items within a weather tight enclosure where they are protected from wetting by rain, snow, condensation, or ground water, and from freezing temperatures. 1.05
PROJECT CONDITIONS A. Hazardous Materials: 1. If materials suspected of containing hazardous materials are encountered, do not disturb; immediately notify Owner's Project Manager. Owner will remove hazardous materials under a separate contract.
PART 2 PRODUCTS – Not Used PART 3 EXECUTION 3.01
GENERAL PROTECTION A. Provide, erect, and maintain temporary dustproof partitions of construction as specified in Supplemental General Conditions. B. Temporary Protection of Historic Materials: 1. Protect existing historic materials with temporary protections and construction. Do not deface or remove existing materials. 2. Do not attach temporary protection to historic surfaces. C. Utility and Communications Services: 1. Notify Owner's Project Manager, authorities having jurisdiction, and entities owning or controlling wires, conduits, pipes, and other services affected by the historic treatment work before commencing operations. 2. Disconnect and cap pipes and services as required by authorities having jurisdiction, as required for the historic treatment work.
3.02
GENERAL HISTORIC TREATMENT PROCEEDURES A. Ensure that field supervisory personnel are on the project site and on duty when historic treatment work begins and during its progress. B. Follow the procedures in subparagraphs below: 1. Retain as much existing material as possible; repair and consolidate rather than replace. 2. Use additional material or structure to reinforce, strengthen, prop, tie, and support existing material or structure. 3. Use reversible processes wherever possible. 4. Use historically accurate repair and replacement materials and techniques unless otherwise indicated. 5. Record existing work with digital photographs as required to provide accurate repair and replacement materials.
C. Where Work requires existing features to be removed or dismantled and reinstalled, perform these operations without damage to the material itself, to adjacent materials, or to the substrate.
Region 1 – Midwest Oregon Courts Security Systems Upgrades
HISTORIC TREATMENT PROCEDURES 013591 3
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
D. Where Work requires existing original door hardware to be removed for salvage and delivery to owner for storage, perform these operations without damage to the material itself, to adjacent materials, or to the substrate. Document each item, indicating location of where the item was removed from. Package hardware for each door in a separate storage box and affix label to box that indicates location information. Deliver storage box to owner. END OF SECTION
Region 1 – Midwest Oregon Courts Security Systems Upgrades
HISTORIC TREATMENT PROCEDURES 013591 4
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 016000 PRODUCT REQUIREMENTS PART 1 GENERAL 1.01 SECTION INCLUDES A.
Re-use of existing products.
B.
Transportation, handling, storage and protection.
C.
Product option requirements.
D.
Substitution limitations and procedures.
E.
Maintenance materials, including extra materials, spare parts, tools, and software.
1.02 RELATED REQUIREMENTS A.
See State of Oregon General Conditions for Public Improvements - Substitutions.
B.
See State of Oregon General Conditions for Public Improvements - Submittals.
1.03 REFERENCE STANDARDS A.
NFPA 70 - National Electrical Code; National Fire Protection Association; Most Recent Edition Adopted by Authority Having Jurisdiction, Including All Applicable Amendments and Supplements.
PART 2 PRODUCTS 2.01 EXISTING PRODUCTS A.
Do not use materials and equipment removed from existing premises unless specifically required or permitted by the Contract Documents.
B.
Unforeseen historic items encountered remain the property of the Building Owner; notify Owner promptly upon discovery; protect, remove, handle, and store as directed by Owner.
C.
Existing materials and equipment indicated to be removed, but not to be re-used, relocated, reinstalled, delivered to the building Owner, or otherwise indicated as to remain the property of the Building Owner, become the property of the Contractor; remove from site.
D.
Reused Products: Reused products include materials and equipment previously used in this or other construction, salvaged and refurbished as specified.
2.02 NEW PRODUCTS A.
Provide new products unless specifically required or permitted by the Contract Documents.
2.03 PRODUCT OPTIONS A.
Products Specified by Reference Standards or by Description Only: Use any product meeting those standards or description.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
PRODUCT REQUIREMENTS 016000 1
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
B.
Products Specified by Naming One or More Manufacturers: Use a product of one of the manufacturers named and meeting specifications, no options or substitutions allowed.
C.
Products Specified by Naming One or More Manufacturers with a Provision for Substitutions: Submit a request for substitution for any manufacturer not named.
2.04 MAINTENANCE MATERIALS A.
Furnish extra materials, spare parts, tools, and software of types and in quantities specified in individual specification sections.
PART 3 EXECUTION 3.01 SUBSTITUTION PROCEDURES A.
Instructions to Bidders specify time restrictions for submitting requests for substitutions during the bidding period. Comply with requirements specified in this section.
B.
Substitutions will not be considered when a product becomes unavailable through no fault of the Contractor.
C.
Document each request with complete data substantiating compliance of proposed substitution with Contract Documents.
D.
A request for substitution constitutes a representation that the submitter: 1. Has investigated proposed product and determined that it meets or exceeds the quality level of the specified product. 2. Will provide the same warranty for the substitution as for the specified product. 3. Will coordinate installation and make changes to other Work that may be required for the Work to be complete with no additional cost to Owner. 4. Waives claims for additional costs or time extension that may subsequently become apparent. 5. Will reimburse Owner and Owner's Authorized Representative for review or redesign services associated with re-approval by authorities.
E.
Substitutions will not be considered when they are indicated or implied on shop drawing or product data submittals, without separate written request, or when acceptance will require revision to the Contract Documents.
F.
Substitution Submittal Procedure: 1. Submit request for substitution on CSI Substitution Request (During the Bidding/Negotiating Stage) Form. 2. Submit three copies of request for substitution for consideration. Limit each request to one proposed substitution. 3. The Owner's Authorized Representative will evaluate request. 4. The Owner's Authorized Project Manager will notify Contractor in writing of decision to accept or reject request.
3.02 TRANSPORTATION AND HANDLING A.
Coordinate schedule of product delivery to designated prepared areas in order to minimize site storage time and potential damage to stored materials.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
PRODUCT REQUIREMENTS 016000 2
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
B.
Transport and handle products in accordance with manufacturer's instructions.
C.
Transport materials in covered trucks to prevent contamination of product and littering of surrounding areas.
D. Promptly inspect shipments to ensure that products comply with requirements, quantities are correct, and products are undamaged. E.
Provide equipment and personnel to handle products by methods to prevent soiling, disfigurement, or damage.
F.
Arrange for the return of packing materials, such as wood pallets, where economically feasible.
3.03 STORAGE AND PROTECTION A.
Designate receiving/storage areas for incoming products so that they are delivered according to installation schedule and placed convenient to work area in order to minimize waste due to excessive materials handling and misapplication.
B.
Store and protect products in accordance with manufacturers' instructions.
C.
Store with seals and labels intact and legible.
D.
Store sensitive products in weather tight, climate controlled, enclosures in an environment favorable to product.
E.
Prevent contact with material that may cause corrosion, discoloration, or staining.
F.
Provide equipment and personnel to store products by methods to prevent soiling, disfigurement, or damage.
END OF SECTION
Region 1 - Midwest Oregon Courts Security Systems Upgrades
PRODUCT REQUIREMENTS 016000 3
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 017000 EXECUTION AND CLOSEOUT REQUIREMENTS PART 1 GENERAL 1.01 SECTION INCLUDES A.
Examination, preparation, and general installation procedures.
B.
Requirements for alterations work, including selective demolition, except removal, disposal, and/or remediation of hazardous materials and toxic substances.
C.
Cutting and patching.
D.
Cleaning and protection.
E.
Starting of systems and equipment.
F.
Demonstration and instruction of Building Owner personnel.
G. Closeout procedures, except payment procedures. 1.02 RELATED REQUIREMENTS A.
Section 011000 - Summary: Limitations on working in existing building; continued occupancy; work sequence; identification of salvaged and relocated materials.
B.
Section 013000 - Administrative Requirements: Submittals procedures.
C.
Section 013591 – Historic Treatment Procedures: General protection and historic treatment procedures for work in spaces, areas, rooms, and surfaces in a designated historic building.
D.
Section 017419 - Construction Waste Management and Disposal: Additional procedures for trash/waste removal, recycling, salvage, and reuse.
E.
Section 024100 - Demolition: Demolition of whole structures and parts thereof; site utility demolition.
F.
Section 078400 - Firestopping.
G. Section 099000 – Paint and Coatings: For finish of cutting and patching work. 1.03 REFERENCE STANDARDS A.
NFPA 241 - Standard for Safeguarding Construction, Alteration, and Demolition Operations; 2013.
1.04 SUBMITTALS A.
See State of Oregon General Conditions for Public Improvement Contracts - Administration of the Contract, for submittal procedures.
B.
Cutting and Patching: Submit written request in advance of cutting or alteration that affects: 1. Structural integrity of any element of Project.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
EXECUTION AND CLOSEOUT REQUIREMENTS 017000 1
DAS Contract Number R02331 HEA Job Number 10013
2. 3. 4. 5. 1.05
27 October 2014 Construction Documents
Integrity of weather exposed or moisture resistant element. Efficiency, maintenance, or safety of any operational element. Visual qualities of sight exposed elements. Work of Owner or separate Contractor.
COORDINATION A.
See Section 011000 for occupancy-related requirements.
B.
Coordinate scheduling, submittals, and work of the various sections of the Project Manual to ensure efficient and orderly sequence of installation of interdependent construction elements, with provisions for accommodating items installed later.
C.
Notify affected utility companies and comply with their requirements.
D.
Verify that utility requirements and characteristics of new operating equipment are compatible with building utilities. Coordinate work of various sections having interdependent responsibilities for installing, connecting to, and placing in service, such equipment.
E.
Coordinate space requirements, supports, and installation of security and electrical work. Follow existing routing for pipes, ducts, and conduit, as closely as practicable; place runs parallel with lines of building. Utilize spaces efficiently to maximize accessibility for other installations, for maintenance, and for repairs.
F.
In finished areas except as otherwise indicated, conceal pipes, ducts, and wiring within the construction. Coordinate locations of fixtures and outlets with finish elements.
G. In finished areas except as otherwise indicated, conceal conduit and wiring within the construction. Coordinate locations of fixtures and outlets with finish elements. H.
Coordinate completion and clean-up of work of separate sections.
I.
After Building Owner occupancy of premises, coordinate access to site for correction of defective work and work not in accordance with Contract Documents, to minimize disruption of Building Owner's activities.
PART 2 PRODUCTS 2.01 PATCHING MATERIALS A.
New Materials: As specified in product sections; match existing products and work for patching and extending work.
B.
Type and Quality of Existing Products: Determine by inspecting and testing products where necessary, referring to existing work as a standard.
PART 3 EXECUTION 3.01 EXAMINATION A.
Verify that existing site conditions and substrate surfaces are acceptable for subsequent work. Start of work means acceptance of existing conditions.
B.
Verify that existing substrate is capable of structural support or attachment of new work
Region 1 - Midwest Oregon Courts Security Systems Upgrades
EXECUTION AND CLOSEOUT REQUIREMENTS 017000 2
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
being applied or attached. C.
Examine and verify specific conditions described in individual specification sections.
D.
Take field measurements before confirming product orders or beginning fabrication, to minimize waste due to over-ordering or mis-fabrication.
E.
Verify that utility services are available, of the correct characteristics, and in the correct locations.
F.
Prior to Cutting: Examine existing conditions prior to commencing work, including elements subject to damage or movement during cutting and patching. After uncovering existing work, assess conditions affecting performance of work. Beginning of cutting or patching means acceptance of existing conditions.
3.02 PREPARATION A.
Clean substrate surfaces prior to applying next material or substance.
B.
Seal cracks or openings of substrate prior to applying next material or substance.
C.
Apply manufacturer required or recommended substrate primer, sealer, or conditioner prior to applying any new material or substance in contact or bond.
3.03 GENERAL INSTALLATION REQUIREMENTS A.
Install products as specified in individual sections, in accordance with manufacturer's instructions and recommendations, and so as to avoid waste due to necessity for replacement.
B.
Make vertical elements plumb and horizontal elements level, unless otherwise indicated.
C.
Install equipment and fittings plumb and level, neatly aligned with adjacent vertical and horizontal lines, unless otherwise indicated.
D.
Make consistent texture on surfaces, with seamless transitions, unless otherwise indicated.
E.
Make neat transitions between different surfaces, maintaining texture and appearance.
3.04 ALTERATIONS A.
Drawings showing existing construction and utilities are based on casual field observation and existing record documents only. 1. Verify that construction and utility arrangements are as shown. 2. Report discrepancies to Owner's Authorized Representative before disturbing existing installation. 3. Beginning of alterations work constitutes acceptance of existing conditions.
B.
Keep areas in which alterations are being conducted separated from other areas that are still occupied. 1. Provide, erect, and maintain temporary dustproof partitions of construction as specified in Supplemental General Conditions.
C.
Maintain weatherproof exterior building enclosure except for interruptions required for
Region 1 - Midwest Oregon Courts Security Systems Upgrades
EXECUTION AND CLOSEOUT REQUIREMENTS 017000 3
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
replacement or modifications; take care to prevent water and humidity damage. 1. Where openings in exterior enclosure exist, provide construction to make exterior enclosure weatherproof. D.
Remove existing work as indicated and as required to accomplish new work. 1. Relocate items indicated on drawings. 2. Where new surface finishes are to be applied to existing work, perform removals, patch, and prepare existing surfaces as required to receive new finish; remove existing finish if necessary for successful application of new finish. 3. Where new surface finishes are not specified or indicated, patch holes and damaged surfaces to match adjacent finished surfaces as closely as possible.
E.
Services (Including but not limited to HVAC, Plumbing, Fire Protection, Electrical, and Telecommunications): Remove, relocate, and extend existing systems to accommodate new construction. 1. Maintain existing active systems that are to remain in operation; maintain access to equipment and operational components; if necessary, modify installation to allow access or provide access panel. 2. Where existing systems or equipment are not active and Contract Documents require reactivation, put back into operational condition; repair supply, distribution, and equipment as required. 3. Where existing active systems serve occupied facilities but are to be replaced with new services, maintain existing systems in service until new systems are complete and ready for service. a. Disable existing systems only to make switchovers and connections; minimize duration of outages. b. See Section 011000 for other limitations on outages and required notifications. c. Provide temporary connections as required to maintain existing systems in service. 4. Verify that abandoned services serve only abandoned facilities. 5. Remove abandoned pipe, ducts, conduits, and equipment, including those above accessible ceilings; remove back to source of supply where possible, otherwise cap stub and tag with identification; patch holes left by removal using materials specified for new construction.
F.
Protect existing work to remain. 1. Prevent movement of structure; provide shoring and bracing if necessary. 2. Perform cutting to accomplish removals neatly and as specified for cutting new work. 3. Repair adjacent construction and finishes damaged during removal work.
G. Adapt existing work to fit new work: Make as neat and smooth transition as possible. H.
Patching: Where the existing surface is not indicated to be refinished, patch to match the surface finish that existed prior to cutting. Where the surface is indicated to be refinished, patch so that the substrate is ready for the new finish.
I.
Refinish existing surfaces as indicated: 1. Where rooms or spaces are indicated to be refinished, refinish all visible existing surfaces to remain to the specified condition for each material, with a neat transition
Region 1 - Midwest Oregon Courts Security Systems Upgrades
EXECUTION AND CLOSEOUT REQUIREMENTS 017000 4
DAS Contract Number R02331 HEA Job Number 10013
2.
27 October 2014 Construction Documents
to adjacent finishes. If mechanical or electrical work is exposed accidentally during the work, re-cover and refinish to match.
J.
Clean existing systems and equipment.
K.
Remove demolition debris and abandoned items from alterations areas and dispose of off-site; do not burn or bury.
L.
Do not begin new construction in alterations areas before demolition is complete.
M. Comply with all other applicable requirements of this section. 3.05 CUTTING AND PATCHING A.
Whenever possible, execute the work by methods that avoid cutting or patching.
B.
See Alterations article above for additional requirements.
C.
Perform whatever cutting and patching is necessary to: 1. Complete the work. 2. Fit products together to integrate with other work. 3. Provide openings for penetration of mechanical, electrical, and other services. 4. Match work that has been cut to adjacent work. 5. Repair areas adjacent to cuts to required condition. 6. Repair new work damaged by subsequent work. 7. Remove samples of installed work for testing when requested. 8. Remove and replace defective and non-conforming work.
D.
Execute work by methods that avoid damage to other work and that will provide appropriate surfaces to receive patching and finishing. In existing work, minimize damage and restore to original condition.
E.
Employ original installer to perform cutting for weather exposed and moisture resistant elements, and sight exposed surfaces.
F.
Cut rigid materials using masonry saw or core drill. Pneumatic tools not allowed without prior approval.
G. Restore work with new products in accordance with requirements of Contract Documents. H.
Fit work air tight to pipes, sleeves, ducts, conduit, and other penetrations through surfaces.
I.
At penetrations of fire rated walls, partitions, ceiling, or floor construction, completely seal voids with fire rated material in accordance with Section 078400, to full thickness of the penetrated element.
J.
Patching: 1. Finish patched surfaces to match finish that existed prior to patching. On continuous surfaces, refinish to nearest intersection or natural break. For an assembly, refinish entire unit. 2. Match color, texture, and appearance. 3. Repair patched surfaces that are damaged, lifted, discolored, or showing other
Region 1 - Midwest Oregon Courts Security Systems Upgrades
EXECUTION AND CLOSEOUT REQUIREMENTS 017000 5
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
imperfections due to patching work. If defects are due to condition of substrate, repair substrate prior to repairing finish. 3.06
PROGRESS CLEANING A.
Maintain areas free of waste materials, debris, and rubbish. Maintain site in a clean and orderly condition.
B.
Remove debris and rubbish from pipe chases, plenums, attics, crawl spaces, and other closed or remote spaces, prior to enclosing the space.
C.
Broom and vacuum clean interior areas prior to start of surface finishing, and continue cleaning to eliminate dust.
D. Collect and remove waste materials, debris, and trash/rubbish from site periodically and dispose off-site; do not burn or bury. 3.07 PROTECTION OF INSTALLED WORK A.
Protect installed work from damage by construction operations.
B.
Provide special protection where specified in individual specification sections.
C.
Provide temporary and removable protection for installed products. Control activity in immediate work area to prevent damage.
D.
Remove protective coverings when no longer needed; reuse or recycle plastic coverings if possible.
3.08 SYSTEM STARTUP A.
Coordinate schedule for start-up of various equipment and systems.
B.
Notify Owner's Authorized Representative and owner's Project Manager seven days prior to start-up of each item.
C.
Verify that each piece of equipment or system has been checked for proper lubrication, drive rotation, belt tension, control sequence, and for conditions that may cause damage.
D.
Verify tests, meter readings, and specified electrical characteristics agree with those required by the equipment or system manufacturer.
E.
Verify that wiring and support components for equipment are complete and tested.
F.
Execute start-up under supervision of applicable Contractor personnel in accordance with manufacturers' instructions.
G. Submit a written report that equipment or system has been properly installed and is functioning correctly. 3.09 DEMONSTRATION AND INSTRUCTION A.
Demonstrate start-up, operation, control, adjustment, trouble-shooting, servicing, maintenance, and shutdown of each item of equipment at scheduled time, at equipment location.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
EXECUTION AND CLOSEOUT REQUIREMENTS 017000 6
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
B.
Provide a qualified person who is knowledgeable about the Project to perform demonstration and instruction of Building Owner's personnel.
C.
Utilize operation and maintenance manuals as basis for instruction. Review contents of manual with Building Owner's personnel in detail to explain all aspects of operation and maintenance.
D.
Prepare and insert additional data in operations and maintenance manuals when need for additional data becomes apparent during instruction.
3.10 ADJUSTING A.
Adjust operating products and equipment to ensure smooth and unhindered operation.
3.11 FINAL CLEANING A.
Execute final cleaning prior to Substantial Completion.
B.
Use cleaning materials that are nonhazardous.
C.
Clean interior surfaces exposed to view effected by alterations; remove stains and foreign substances, polish transparent and glossy surfaces, vacuum carpeted and soft surfaces.
D.
Clean equipment and fixtures to a sanitary condition with cleaning materials appropriate to the surface and material being cleaned.
E.
Remove waste, surplus materials, trash/rubbish, and construction facilities from the site; dispose of in legal manner; do not burn or bury.
3.12 CLOSEOUT PROCEDURES A.
Make submittals that are required by governing or other authorities.
B.
Notify Owner's Authorized Representative and Owner's Project manager when work is considered ready for Substantial Completion.
C.
Submit written certification that Contract Documents have been reviewed, work has been inspected, and that work is complete in accordance with Contract Documents and ready for Owner's Authorized Representative's review.
D.
Building Owner will occupy all of the building as specified in Section 011000.
E.
Correct items of work listed in executed Certificates of Substantial Completion and comply with requirements for access to Building Owner-occupied areas.
F.
Notify Owner's Authorized Representative when work is considered finally complete.
G. Complete items of work determined by Owner's Authorized Representative's final inspection. END OF SECTION
Region 1 - Midwest Oregon Courts Security Systems Upgrades
EXECUTION AND CLOSEOUT REQUIREMENTS 017000 7
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 017419 CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL PART 1 GENERAL 1.01 WASTE MANAGEMENT REQUIREMENTS A.
Owner requires that this project generate the least amount of trash and waste possible.
B.
Employ processes that ensure the generation of as little waste as possible due to error, poor planning, breakage, mishandling, contamination, or other factors.
C.
Minimize trash/waste disposal in landfills; reuse, salvage, or recycle as much waste as economically feasible.
D.
Required Recycling, Salvage, and Reuse: The following may not be disposed of in landfills or by incineration: 1. Aluminum and plastic beverage containers. 2. Corrugated cardboard. 3. Wood pallets. 4. Clean dimensional wood: May be used as blocking or furring. 5. Metals, including packaging banding, metal studs, sheet metal, structural steel, piping, reinforcing bars, door frames, and other items made of steel, iron, galvanized steel, stainless steel, aluminum, copper, zinc, lead, brass, and bronze. 6. Paint. 7. Mechanical and electrical equipment.
E.
Contractor shall develop and follow a Waste Management Plan designed to implement these requirements.
F.
Methods of trash/waste disposal that are NOT acceptable are: 1. Burning on the project site. 2. Burying on the project site. 3. Dumping or burying on other property, public or private. 4. Other illegal dumping or burying. 5. Incineration, either on- or off-site.
G. Regulatory Requirements: Contractor is responsible for knowing and complying with regulatory requirements, including but not limited to Federal, state and local requirements, pertaining to legal disposal of all construction and demolition waste materials. 1.02 DEFINITIONS A.
Clean: Untreated and unpainted; not contaminated with oils, solvents, caulk, or the like.
B.
Construction and Demolition Waste: Solid wastes typically including building materials, packaging, trash, debris, and rubble resulting from construction, remodeling, repair and demolition operations.
C.
Hazardous: Exhibiting the characteristics of hazardous substances, i.e., ignitibility, corrosively, toxicity or reactivity.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL 017419 1
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
D.
Nonhazardous: Exhibiting none of the characteristics of hazardous substances, i.e., ignitibility, corrosively, toxicity, or reactivity.
E.
Nontoxic: Neither immediately poisonous to humans nor poisonous after a long period of exposure.
F.
Recyclable: The ability of a product or material to be recovered at the end of its life cycle and remanufactured into a new product for reuse by others.
G. Recycle: To remove a waste material from the project site to another site for remanufacture into a new product for reuse by others. H.
Recycling: The process of sorting, cleansing, treating and reconstituting solid waste and other discarded materials for the purpose of using the altered form. Recycling does not include burning, incinerating, or thermally destroying waste.
I.
Return: To give back reusable items or unused products to vendors for credit.
J.
Reuse: To reuse a construction waste material in some manner on the project site.
K.
Salvage: To remove a waste material from the project site to another site for resale or reuse by others.
L.
Sediment: Soil and other debris that has been eroded and transported by storm or well production run-off water.
M. Source Separation: The act of keeping different types of waste materials separate beginning from the first time they become waste. N. Toxic: Poisonous to humans either immediately or after a long period of exposure. O. Trash: Any product or material unable to be reused, returned, recycled, or salvaged. P.
Waste: Extra material or material that has reached the end of its useful life in its intended use. Waste includes salvageable, returnable, recyclable, and reusable material.
1.03 SUBMITTALS A.
Submit Waste Management Plan within 10 calendar days after receipt of Notice of Award of Bid, or prior to any trash or waste removal, whichever occurs sooner; submit projection of all trash and waste that will require disposal and alternatives to landfilling.
PART 2 PRODUCTS - NOT USED PART 3 EXECUTION 3.01 WASTE MANAGEMENT PLAN IMPLEMENTATION A.
Manager: Designate an on-site person or persons responsible for instructing workers and overseeing and documenting results of the Waste Management Plan.
B.
Communication: Distribute copies of the Waste Management Plan to job site foreman, each subcontractor, Owner, and Owner's Project Manager.
C.
Instruction: Provide on-site instruction of appropriate separation, handling, and recycling, salvage, reuse, and return methods to be used by all parties at the appropriate stages of
Region 1 - Midwest Oregon Courts Security Systems Upgrades
CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL 017419 2
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
the project. D.
Meetings: Discuss trash/waste management goals and issues at project meetings. 1. Pre-construction meeting.
E.
Facilities: Provide specific facilities for separation and storage of materials for recycling, salvage, reuse, return, and trash disposal, for use by all contractors and installers. 1. Provide containers as required. 2. Provide adequate space for pick-up and delivery and convenience to subcontractors. 3. Keep recycling and trash/waste bin areas neat and clean and clearly marked in order to avoid contamination of materials.
F.
Hazardous Wastes: Separate, store, and dispose of hazardous wastes according to applicable regulations.
G. Recycling: Separate, store, protect, and handle at the site identified recyclable waste products in order to prevent contamination of materials and to maximize recyclability of identified materials. Arrange for timely pickups from the site or deliveries to recycling facility in order to prevent contamination of recyclable materials. H.
Reuse of Materials On-Site: Set aside, sort, and protect separated products in preparation for reuse for items/ materials specifically indicated to be reused.
I.
Salvage: Set aside, sort, and protect products to be salvaged for reuse.
END OF SECTION
Region 1 - Midwest Oregon Courts Security Systems Upgrades
CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL 017419 3
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 024100 DEMOLITION PART 1 GENERAL 1.01 SECTION INCLUDES A.
Selective demolition of building elements for alterations purposes, excluding removal of hazardous materials and toxic substances.
B.
Abandonment and removal of existing utilities and utility structures.
1.02 RELATED REQUIREMENTS A.
Section 011000 - Summary: Limitations on Contractor's use of site and premises.
B.
Section 017000 – Execution and Closeout Requirements: Cutting and Patching.
C.
Section 017419 - Construction Waste Management and Disposal: Limitations on disposal of removed materials; requirements for recycling.
D.
Section 013591 – Historic Treatment Procedures: Limitations on removal of items from specific historic spaces, areas, rooms and surfaces.
1.03 REFERENCE STANDARDS A.
29 CFR 1926 - U.S. Occupational Safety and Health Standards; current edition.
B.
NFPA 241 - Standard for Safeguarding Construction, Alteration, and Demolition Operations; 2013.
1.04 SUBMITTALS A.
See State of Oregon General Conditions for Public Improvement Contracts - Administration of the Contract, for submittal procedures.
B.
Project Record Documents: Accurately record actual locations of capped and active utilities and subsurface construction.
1.05 QUALITY ASSURANCE A.
Demolition Firm Qualifications: Company specializing in the type of work required. 1. Minimum of 3 years of documented experience.
PART 2 PRODUCTS -- NOT USED PART 3 EXECUTION 3.01 SCOPE A.
Remove any existing non-structural materials found to be in the way of installing the materials and systems incorporated in the new design.
B.
Remove other items for salvage, relocation, and recycling.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
DEMOLITION 024100 1
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
3.02 GENERAL PROCEDURES AND PROJECT CONDITIONS A.
Comply with other requirements in the State of Oregon General Conditions for Public Improvement Contracts.
B.
Comply with applicable codes and regulations for demolition operations including safety of adjacent structures and the public. 1. Obtain required permits. 2. Provide, erect, and maintain temporary barriers and security devices. 3. Use physical barriers to prevent access to areas that could be hazardous to workers or the public. 4. Conduct operations to minimize effects on and interference with adjacent structures and occupants. 5. Do not close or obstruct roadways or sidewalks without permit. 6. Conduct operations to minimize obstruction of public and private entrances and exits; do not obstruct required exits at any time; protect persons using entrances and exits from removal operations. 7. Obtain written permission from owners of adjacent properties when demolition equipment will traverse, infringe upon or limit access to their property.
C.
Do not begin removal until receipt of notification to proceed from Owner's Project Manager.
D.
Do not begin demolition until required phasing plans have been approved by Owner's Project Manager.
E.
Do not begin removal until built elements to be salvaged or relocated have been removed.
F.
Protect existing structures and other elements that are not to be removed. 1. Provide bracing and shoring. 2. Prevent movement or settlement of adjacent structures. 3. Stop work immediately if adjacent structures appear to be in danger.
G. Minimize production of dust due to demolition operations; do not use water if that will result in ice, flooding, sedimentation of public waterways or storm sewers, or other pollution. H.
If hazardous materials are discovered during removal operations, stop work and notify Owner's Project Manager; hazardous materials include regulated asbestos containing materials, lead, PCB's, and mercury.
I.
Perform demolition in a manner that maximizes salvage and recycling of materials. 1. Dismantle existing construction and separate materials. 2. Set aside reusable, recyclable, and salvageable materials; store and deliver to collection point or point of reuse.
J.
Partial Removal of Concrete: Neatly saw cut at right angle to surface.
3.03 EXISTING UTILITIES A.
Coordinate work with utility companies; notify before starting work and comply with their requirements; obtain required permits.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
DEMOLITION 024100 2
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
B.
Protect existing utilities to remain from damage.
C.
Do not disrupt public utilities without permit from authority having jurisdiction.
D.
Do not close, shut off, or disrupt existing life safety systems that are in use without at least 10 days prior written notification to Building Owner.
E.
Do not close, shut off, or disrupt existing utility branches or take-offs that are in use without at least 5 days prior written notification to Building Owner.
F.
Shutoffs of utilities and building systems shall not occur during business hours.
G. Locate and mark utilities to remain; mark using highly visible tags or flags, with identification of utility type; protect from damage due to subsequent construction, using substantial barricades if necessary. 3.04 SELECTIVE DEMOLITION FOR ALTERATIONS A.
Drawings showing existing construction and utilities are based on casual field observation only. 1. Verify that construction and utility arrangements are as shown. 2. Report discrepancies to Owner's Project Manager before disturbing existing installation. 3. Beginning of demolition work constitutes acceptance of existing conditions that would be apparent upon examination prior to starting demolition.
B.
Separate areas in which demolition is being conducted from other areas that are still occupied. 1. Provide, erect, and maintain temporary dustproof partitions of construction as required to maintain separation.
C.
Remove existing work as indicated and as required to accomplish new work.
D.
Services (Including but not limited to Electrical and Telecommunications): Remove existing systems and equipment as indicated. 1. Maintain existing active systems that are to remain in operation; maintain access to equipment and operational components. 2. Where existing active systems serve occupied facilities but are to be replaced with new services, maintain existing systems in service until new systems are complete and ready for service. 3. See Section 011000 for other limitations on outages and required notifications. 4. Verify that abandoned services serve only abandoned facilities before removal. 5. Remove abandoned pipe, ducts, conduits, and equipment, including those above accessible ceilings; remove back to source of supply where possible, otherwise cap stub and tag with identification.
E.
Protect existing work to remain. 1. Prevent movement of structure; provide shoring and bracing if necessary. 2. Perform cutting to accomplish removals neatly and as specified for cutting new work. 3. Repair adjacent construction and finishes damaged during removal work. 4. Patch as specified for patching new work.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
DEMOLITION 024100 3
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
3.05 DEBRIS AND WASTE REMOVAL A.
Remove debris, junk, and trash from site.
B.
Remove from site all materials not to be reused on site; comply with requirements of Section 017419 – Construction Waste Management and Disposal.
C.
Leave site in clean condition, ready for subsequent work.
D.
Clean up spillage and wind-blown debris from public and private lands.
END OF SECTION
Region 1 - Midwest Oregon Courts Security Systems Upgrades
DEMOLITION 024100 4
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 078400 FIRESTOPPING PART 1 GENERAL 1.01 SECTION INCLUDES A.
Firestopping systems.
B.
Firestopping of all joints and penetrations in fire-resistance rated and smoke-resistant assemblies, whether indicated on drawings or not, and other openings indicated.
1.02 RELATED REQUIREMENTS A.
See State of Oregon General Conditions for Public Improvement Contracts - Job Site conditions: Cutting and patching.
1.03 REFERENCE STANDARDS A.
ASTM E 119 - Standard Test Methods for Fire Tests of Building Construction and Materials; 2009c.
B.
ASTM E 814 - Standard Test Method for Fire Tests of Through-Penetration Fire Stops; 2009.
C.
ITS (DIR) - Directory of Listed Products; Intertek Testing Services NA, Inc.; current edition.
D.
FM 4991 - Approval of Firestop Contractors; Factory Mutual Research Corporation; 2001.
E.
FM P7825 - Approval Guide; Factory Mutual Research Corporation; current edition.
F.
SCAQMD 1168 - South Coast Air Quality Management District Rule No.1168; current edition; www.aqmd.gov.
G. UL (FRD) - Fire Resistance Directory; Underwriters Laboratories Inc.; current edition. 1.04 SUBMITTALS A.
See State of Oregon General Conditions for Public Improvement Contracts - Administration of the Contract, for submittal procedures.
B.
Product Data: Provide data on product characteristics, performance ratings, and limitations.
C.
Manufacturer's Installation Instructions: Indicate preparation and installation instructions.
D.
Manufacturer's Certificate: Certify that products meet or exceed specified requirements.
1.05 QUALITY ASSURANCE A.
Fire Testing: Provide firestopping assemblies of designs that provide the scheduled fire ratings when tested in accordance with methods indicated. 1. Listing in the current-year classification or certification books of UL, FM, or ITS (Warnock Hersey) will be considered as constituting an acceptable test report.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
FIRESTOPPING 078400 1
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
1.06 FIELD CONDITIONS A.
Comply with firestopping manufacturer's recommendations for temperature and conditions during and after installation. Maintain minimum temperature before, during, and for 3 days after installation of materials.
B.
Provide ventilation in areas where solvent-cured materials are being installed.
PART 2 PRODUCTS 2.01 FIRESTOPPING SYSTEMS A.
Firestopping: Any material meeting requirements. 1. Fire Ratings: Use any system listed by UL or tested in accordance with ASTM E 814 that has F Rating equal to fire rating of penetrated assembly and minimum T Rating Equal to F Rating and that meets all other specified requirements.
2.02 MATERIALS A.
Firestopping Sealants: Provide only products having lower volatile organic compound (VOC) content than required by South Coast Air Quality Management District Rule No.1168.
B.
Primers, Sleeves, Forms, Insulation, Packing, Stuffing, and Accessories: Type required for tested assembly design.
PART 3 EXECUTION 3.01 EXAMINATION A.
Verify openings are ready to receive the work of this section.
3.02 PREPARATION A.
Clean substrate surfaces of dirt, dust, grease, oil, loose material, or other matter that could adversely affect bond of firestopping material.
B.
Remove incompatible materials that could adversely affect bond.
3.03 INSTALLATION A.
Install materials in manner described in fire test report and in accordance with manufacturer's instructions, completely closing openings.
B.
Do not cover installed firestopping until inspected by authority having jurisdiction.
3.04 CLEANING A.
Clean adjacent surfaces of firestopping materials.
3.05 PROTECTION A.
Protect adjacent surfaces from damage by material installation.
END OF SECTION
Region 1 - Midwest Oregon Courts Security Systems Upgrades
FIRESTOPPING 078400 2
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 087100 DOOR HARDWARE PART 1 GENERAL 1.01
SUMMARY
A. SECTION INCLUDES 1. The work in this section includes furnishing all items of finish hardware as hereinafter specified or obviously necessary for all swinging, sliding, folding and other doors related to the Access Control systems. B. RELATED DOCUMENTS 1. Related documents, drawings and general provisions of contract, including General and Supplementary Conditions and Division 1 specification sections apply to this section. C. RELATED SECTIONS 1. 087101 – Hardware Groups 2. 281300 – Access Control 1.02
REFERENCES
A. STANDARDS 1. ANSI-A250.4 – Steel Doors and Frames Physical Endurance 2. ANSI A156.1 – Butts and Hinges 3. ANSI A156.2 – Bored Locks and Latches 4. ANSI A156.3 – Exit Devices 5. ANSI A156.4 – Door Controls – Door Closers 6. ANSI A156.5 – Auxiliary Locks and Associated Products 7. ANSI A156.6 – Architectural Door Trim 8. ANSI A156.7 – Template Hinge Dimensions 9. ANSI A156.8 – Door Controls – Overhead Holders 10. ANSI A156.13 – Mortise Locks and Latches 11. ANSI A156.15 – Closer Holder Release Devices 12. ANSI A156.16 – Auxiliary Hardware 13. ANSI A156.18 – Material and Finishes 14. UL10C – Positive Pressure Fire Tests of Door Assemblies B. CODES 1. NFPA 101 – Life Safety Code Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 1
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
2. OSSC 2014 – Oregon Structural Specialty Code 3. ANSI A117.1 (2009) – Standard for Accessible and Usable Buildings and Facilities 4. ADA – Americans with Disabilities Act 1.03
SUBMITTALS
A. GENERAL REQUIREMENTS 1. Submit copies of finish hardware schedule in accordance with General and Supplementary Conditions. B. SCHEDULES AND PRODUCT DATA 1. Schedules to be in vertical format, listing each door opening, and organized into “hardware groups” indicating complete designations of every item required for each door opening to function as intended. Hardware schedule shall be submitted within two (2) weeks from date the purchase order is received by the finish hardware supplier. Furnish four (4) copies of revised schedules after approval for field and file use. Note any special mounting instructions or requirements with the hardware schedule. Schedules to include the following information: a. Location of each hardware group cross-referenced to indications on drawings, both on floor plans and access control equipment schedule. b. Keying information. c. Type, style, function, size, and finish of each hardware item. d. Elevation drawings and operational descriptions for all electronic openings. e. Name and manufacturer of each hardware item. f. Fastenings and other pertinent information. g. Explanation of all abbreviations, symbols and codes contained in schedule h. Mounting locations for hardware when varies from standard. 2. Submit catalog cuts and/or product data sheets for all scheduled finish hardware. 3. Submit separate detailed keying schedule for approval indicating clearly how the owner’s final instructions on keying of locks has been fulfilled. C. SAMPLES 1. Upon request, samples of each type of hardware in finish indicated shall be submitted. Samples are to remain undamaged and in working condition through submittal and review process. Items will be returned to the supplier or incorporated into the work within limitations of keying coordination requirements.
Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 2
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
D. TEMPLATES 1. Furnish a complete list and suitable templates, together with finish hardware schedule to contractor, for distribution to necessary trades supplying materials to be prepped for finish hardware. E. ELECTRONIC HARDWARE SYSTEMS 1. Provide complete wiring diagrams prepared by an authorized factory employee for each opening requiring electronic hardware. Provide a copy with each hardware schedule submitted after approval. 2. Provide complete operational descriptions of electronic components listed by opening in the hardware submittals. Operational descriptions to detail how each electrical component functions within the opening incorporating all conditions of ingress and egress. Provide a copy with each hardware schedule submitted for approval. 3. Provide elevation drawings of electronic hardware and systems identifying locations of the system components with respect to their placement in the door opening. Provide a copy with each hardware schedule submitted for approval. 4. Prior to installation of electronic hardware, arrange conference between supplier, installers and related trades to review materials, procedures and coordinating related work. 5. The electrical products contained within this specification represent a complete engineered system. If alternate electrical products are submitted, it is the responsibility of the distributor to bear the cost of providing a complete and working system including re-engineering of electrical diagrams and system layout, as well as power supplies, power transfers and all required electrical components. Coordinate with electrical engineer and electrician to ensure that line voltage and low voltage wiring is coordinated to provide a complete and working system. F. OPERATIONS AND MAINTENANCE MANUALS 1. Upon completion of construction and building turnover, furnish two (2) complete maintenance manuals to the owner. Manuals to include the following items: a. Approved hardware schedule, catalog cuts and keying schedule. b. Hardware installation and adjustment instructions. c. Manufacturer’s written warranty information. d. Wiring diagrams, elevation drawings and operational descriptions for all electronic openings.
Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 3
DAS Contract Number R02331 HEA Job Number 10013
1.04
27 October 2014 Construction Documents
QUALITY ASSURANCE
A. SUBSTITUTIONS 1. All substitution requests must be submitted before bidding and within the procedures and time frame as outlined in Division 1, Product Requirements. Approval of products is at the discretion of the owner's authorized representative and their hardware consultant. B. SUPPLIER QUALIFICATIONS 1. A recognized architectural door hardware supplier who has maintained an office and has been furnishing hardware in the project’s vicinity for a period of at least two (2) years. Hardware supplier shall have office and warehouse facilities to accommodate this project and must be an authorized factory distributor of all products specified herein. Hardware supplier shall have in his employment at least one (1) Architectural Hardware Consultant (AHC) who is available at reasonable times during business hours for consultation about the project’s hardware and requirements to the owner, owner's authorized representative and contractor. 1.05
FIRE-RATED OPENINGS 1. Provide door hardware for fire-rated openings that comply with NFPA 80 and requirements of authorities having jurisdiction. Provide only items of door hardware that are listed by Underwriter’s Laboratories (UL) or Warnock Hersey (WH) for use on types and sizes of doors indicated.
1.06
DELIVERY, STORAGE AND HANDLING
A. MARKING AND PACKAGING 1. Properly package and mark items according to the approved hardware schedule, complete with necessary screws and accessories, instructions and installation templates for spotting mortising tools. Contractor shall check deliveries against accepted list and provide receipt for them, after which he is responsible for storage and care. Any shortage or damaged good shall be made without cost to the owner. 2. Packaging of door hardware is the responsibility of the supplier. As hardware supplier receives material from various manufacturers, sort and repackage in containers clearly marked with appropriate hardware set and door numbers to match the approved hardware schedule. Two or more identical sets may be packed in same container.
Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 4
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
B. DELIVERY 1. The supplier shall deliver all hardware to the project site; direct factory shipments are not allowed unless agreed upon beforehand. Hardware supplier shall coordinate delivery times and schedules with the contractor. Inventory door hardware jointly with representatives of hardware supplier and hardware installer/contractor until each is satisfied that count is correct. 2. No keys, other than construction master keys and/or temporary keys are to be packed in boxes with the locks. C. STORAGE 1. Provide secure lock-up for door hardware delivered to the Project, but not yet installed. Control handling and installation of hardware items that are not immediately replaceable so that completion of work will not be delayed by hardware losses both before and after installation. 1.07
WARRANTY
A. All items, except as noted below, shall be warranted in writing by the manufacturer against failure due to defective materials and workmanship for a minimum period of one (1) year commencing on the date of final completion and acceptance. In the event of product failure, promptly repair or replace item with no additional cost to the owner. 1. 2. 3. 4. 5.
Cylindrical locksets – Heavy Duty: Seven (7) years Mortise locksets: Seven (7) years Exit Devices: Five (5) years Door closers: Ten (10) years Electrified hardware: Unlimited Lifetime
PART II – PRODUCTS 2.01
MANUFACTURERS
A. Obtain each type of finish hardware (hinges, latch and locksets, exit devices, door closers, etc.) from a single manufacturer. 2.02
MATERIALS
A. SCREWS AND FASTENERS 1. All required screws shall be supplied as necessary for securing finish hardware in the appropriate manner. Thru-bolts shall be supplied for exit devices and door closers where required by code and the appropriate blocking or reinforcing is not present in the door to preclude their use. Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 5
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
B. HANGING DEVICES 1. HINGES a. Hinges shall conform to ANSI A156.1 and have the number of knuckles as specified, oil-impregnated bearings as specified with NRP (non-removable pin) feature, at all exterior reverse bevel doors. Unless otherwise scheduled, supply one (1) hinge for every 30” of door height. Unless otherwise specified, supply hinges 4 1/2" in height on doors up to 36” and hinges 5” in height on doors over 36” and up to 48” in width; heavy weight hinges (.180) shall be supplied at all doors where specified. 1) Specified Manufacturer: McKinney 2) Approved Substitutes: Hager, Stanley 2. ELECTRIC HINGES a. Electric hinges shall be provided with molex standardized plug connectors to accommodate up to twelve (12) wires. Plug connectors shall plug directly into molex through-door wiring harnesses for connection to electric locking devices and power supplies. Provide sufficient number of concealed wires to accommodate electric function of specified hardware. Provide a mortar guard for each electric hinge specified. 1) Specified Manufacturer: a) McKinney QC Series 2) Approved Substitutes: a) Hager ETW-QC Series b) Security Door Controls 3. MONITORING SWITCH HINGES a. Monitoring switch hinges to be magnetic reed, concealed, adjustable switch type with extra heavy magnet. 1) Specified Manufacturer: McKinney MM Series 2) Approved Substitutes: Hager EMN Series, Stanley CS Series C. FLUSH BOLTS AND ACCESSORIES 1. All manual and automatic flush bolts to be furnished as specified. a. Specified Manufacturer: Rockwood b. Approved Substitutes: McKinney, Quality, Trimco
Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 6
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
D. CYLINDERS AND KEYING 1. KEYING a. All permanent locks and cylinders will be keyed into buildings existing system by the contractor. Field verify correct keyway and system with Building Owner. Furnish the following key amounts: 1) Two (2) blank keys per lock for owners use in keying 2) If required for sequence of installation provide Fifteen (15) construction/temporary keys b. High-security or restricted keyway blanks shall be sealed in tamper-proof packaged boxes when shipped from the factory. The boxes shall be shrink wrapped and imprinted to ensure the integrity of the packaging. 2. CYLINDER INSTALLATION a. If required for sequence of installation the general contractor shall install all construction cylinders/cores, at the time of hardware installation. b. The general contractor shall remove all construction cylinders/cores, and install all permanent cylinders/cores. Coordinate with Building Owner to provide the correct keyway and system. Construction cylinders/cores are to be returned to the hardware supplier. E. LOCKSETS 1. MORTISE LOCKSETS a. All locksets shall be ANSI 156.13 Series 1000, Grade 1 Certified. All functions shall be manufactured in a single sized case formed from 12 gauge steel minimum. The lockset shall have a field-adjustable, beveled armored front, with a .125” minimum thickness and shall be reversible without opening the lock body. The lockset shall be 2 3/4” backset with a one-piece 3/4” anti-friction stainless steel latchbolt. The deadbolt shall be a full 1” throw made of stainless steel and have 2 hardened steel roller inserts. All strikes shall be non-handed with a curved lip. To insure proper alignment, all trim, shall be thru-bolted and fully interchangeable between rose and escutcheon designs and shall be the product of one manufacturer. 1) Specified Manufacturer: Sargent 8200 Series 2) Approved Substitutes: Corbin Russwin ML2000 Series, Schlage L9000 Series, Yale 8800 Series.
Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 7
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
2. CYLINDRICAL LOCKSETS – HEAVY DUTY a. All locksets shall be ANSI 156.2 Series 4000, Grade 1 Certified. Furnish with standard 2 3/4” backset. Lock housing shall be fabricated of steel zinc dichromate and stainless steel. Latchbolt shall be brass or stainless steel with a minimum 1/2” throw. Locks shall be non-handed and fully field reversible. 1) Specified Manufacturer: Sargent 10 Line 2) Approved Substitutes: Corbin Russwin CL3300 Series, Schlage ND Series, Yale 5400LN Series 3. ELECTRIFIED LOCKSETS a. Mechanical features of locksets shall conform to standards as specified above. Locksets shall be fail-secure unless otherwise specified. Where specified electrified locksets shall be provided with a switch to monitor inside or outside lever handle or signal remote location. Provide an in-line power controller with all electrified locksets. 1) Specified Manufacturers: Sargent 2) Approved Manufacturers: Corbin Russwin, Schlage, Yale F. ELECTRIC STRIKES 1. STANDARD STRIKES a. All standard electric strikes shall meet BHMA standard 501, grade 1 and be UL Listed for Burglary Resistance, category 1034. Strikes shall be all stainless steel construction for corrosion resistance, strength and durability. Strikes shall have been tested to withstand a forcing strength of a minimum 2400 lbs. before releasing and perform with a minimum of one million cycles of operation. Strikes shall be 24VDC fail-secure unless otherwise specified. Provide an in-line power controller with all electric strikes. 1) Specified Manufacturers: HES 1006 Series 2) Approved Substitutes: Folger Adams 742 Series 2. SURFACE MOUNTED STRIKES a. All surface mounted electric strikes shall meet BHMA standard 501, grade 1 and be UL Listed for Burglary Resistance, category 1034. Strikes shall have two heavy-duty, stainless steel locking mechanisms operating independently to provide tamper resistance. Optional latchbolt and latchbolt strike monitoring that indicates position of the latchbolt and locked condition of the strike shall be available. Strikes shall have been tested for a minimum of 500,000 operating cycles. Provide an in-line power controller with all electric strikes. 1) Specified Manufacturers: HES 9500 / 9600 Series 2) Approved Substitutes: NONE Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 8
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
G. ELECTROMAGNETIC LOCKS 1. MAGNALOCKS a. Magnalocks shall operate on 24VDC input and shall not consume more than three (3) watts of power (125mA @ 24VDC). The magnalock shall be capable of providing a pull-apart or tensile holding force of at least 1200 pounds. The strike plate shall be mounted using a steel sex bolt and roll pin to provide a “floating” movement to assure automatic self-alignment with the lock. Anti-tamper caps shall be provided for the exposed holes. The lock and strike shall be plated to provide corrosion proofing. The lock shall be full sealed in resin to make it tamper and weather proof. The lock shall contain a suppression circuit to prevent residual magnetism and inductive kickback. The circuit also shall provide accelerated field collapse and radiation suppression. Ten feet of jacketed stranded conductor shall be provided for electrical connection. 1) Specified Manufacturers: Securitron Model 62 2) Approved Manufacturers: Folger Adams 2. SHEAR LOCKS a. Shear locks shall be produced by an ISO 9001 certified manufacturer. The lock shall be of the self-aligning magnetic shear type suitable for mortise mounting and shall not exceed 15 cubic inches. The lock shall be “dual voltage” accepting 12 or 24VDC without the alteration of any settings at the time of the installation. The power requirements of the lock shall not exceed four Watts (160mA @ 24VDC). The lock shall be self-contained with no external circuit board and will self align into the locked position when the door closes without the need for door position sensing or timers. The lock shall not be position sensitive; it may be mounted at the top or side of the door and will operate on single or double acting doors. The lock shall be fully sealed in resin to make it tamper proof. 1) Specified Manufacturer: Securitron SAM 2) Approved Substitutes: Folger Adams 3. MAGNALOCK – CABINET a. Magnalocks shall operate on 24VDC input. The strike plate shall be mounted using a steel sex bolt and roll pin to provide a “floating” movement to assure automatic self-alignment with the lock. Ten feet of jacketed stranded conductor shall be provided for electrical connection. 1) Specified Manufacturers: Securitron Model MCL-24
Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 9
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
H. EXIT DEVICES 1. CONVENTIONAL DEVICES – PUSH RAIL a. All exit devices shall be ANSI A156.3, Grade 1 Certified and shall be listed by Underwriters Laboratories and bear the UL label for life safety in full compliance with NFPA 80 and NFPA 101. Mounting rails shall be formed from a solid single piece of stainless steel, brass or bronze no less than 0.072” thick. Push rails shall be constructed of 0.062” thick material. Lever trim shall be available in finishes and designs to match that of the specified locksets. 1) Specified Manufacturer: Sargent 80 Series 2) Approved Substitutes: Adams Rite 8800 Series, Corbin Russwin ED4000/ED5000 Series, Von Duprin 98 Series, Yale 7100/7200 Series 2. ELECTRIFIED DEVICES a. Electrified exit devices shall conform to all traditional exit device standards as specified above. All power requirements for exit devices used must utilize a continuous circuit electric hinge for clean design and no visible means of interrupting power to device. 1) Specified Manufacturer: Detex 10 Series 2) Approved Substitutes: Von Duprin CX Series b. All exit devices, both fire labeled and non-labeled devices, requiring electric dogging shall be held in the "dogged" or retracted position. All exit devices with electric latch retraction shall provide for a remote means of unlocking for momentary or maintained periods of time. c. Exit devices with electrified trim shall be fail-secure unless otherwise specified. d. Exit devices shall be provided with a switch to monitor push rail or signal remote location and latchbolt monitoring. e. Provide an in-line power controller with all electrified exit devices as required. 1) Specified Manufacturers: Sargent 2) Approved Manufacturers: Corbin Russwin, Von Duprin, Yale 3. TOUCH SENSE EXIT BARS a. Touch sense bars shall employ an anodized aluminum finish and shall activate a relay when touched (no mechanical movement) which will allow free egress or initiate the delay on an exit delay timer. Touch sense bars shall operate on either 12 or 24 VAC or VDC. 1) Specified Manufacturer: Securitron TSB 2) Approved Substitutes: Folger Adams Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 10
DAS Contract Number R02331 HEA Job Number 10013
I.
27 October 2014 Construction Documents
DOOR CLOSERS 1. SURFACE MOUNTED CLOSERS – EXTRA HEAVY DUTY a. All door closers shall be ANSI 156.4, Grade 1 Certified. All surface closers shall be of full rack and pinion construction. Closing speed, latching speed and backcheck shall be controlled by key operated valves. Closers shall be non-handed to meet a variety of door conditions and design requirements. Closers shall project no more than 2 3/4” from the surface of the door. All arms shall be finely finished with heavy duty forged steel main arm and closer covers shall be of high impact plastic material of flame retardant grade. Provide drop plates or other accessories as required for proper mounting. 1) Specified Manufacturer: Stanley QDC 100 Series 2) Approved Substitutes: Corbin Russwin DC8000 Series, Sargent 281 Series, Yale 400 Series, Norton 7700 Series
J.
ELECTRONIC PRODUCTS AND ACCESSORIES 1. KEYSWITCHES a. Keyswitches shall be furnished on a stainless steel single gang face plate with a 12/24VDC bi-color LED and an integral backing bracket that shall permit integration with any 1.25” or 1.125” mortise cylinder. Keyswitches shall be available for momentary or maintained action and in narrow stile designs. 1) Specified Manufacturers: Securitron MK Series 2) Approved Manufacturers: Folger Adams 2. POWER SUPPLIES a. Power supplies shall furnish regulated 24VDC and shall be UL class 2 listed. LED’s shall monitor zone status (voltage/no voltage) and slide switches shall be provided to connect or disconnect the load from power; 1, 4 or 8 separate output circuit breakers shall be provided to divide the load. Power supplies shall have the internal capability of charging optional 24VDC sealed lead acid batteries in addition to operating the DC load. Power supplies shall be supplied complete requiring only 120VAC to the fused input and shall be supplied in an enclosure. Power supplies shall be provided with emergency release terminals that allow the release of all devices upon activation of the fire alarm system. 1) Specified Manufacturer: Securitron BPS 2) Approved Substitutes: Folger Adams
Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 11
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
3. EMERGENCY EXIT BUTTON a. Integrated retriggerable 30 second timer, mounted on stainless steel single gang faceplate. Push button shall be 2" x 2" industrial grade button with protective cowling. Push button to be labeled 'PUSH TO EXIT' and shall be non-illuminated. The unit shall operate on 12 or 24 VDC (Must be the same voltage as the installed lock). Push button to be mounted within 5'-0" of the door at a height of 44" above finish floor. 1) Specified Manufacturers: Securitron EEB Series 4. DOOR RELEASE PUSH BUTTON a. Push button with vandal-resistant stainless button with illuminated green Halo-style button. The unit shall operate on 7 amp rated contacts. Verify mounting location with owner. 1) Specified Manufacturers: Securitron PB Series 5. ALARM SOUNDER a. Alarm sounder mounted on stainless steel single gang faceplate. Local alarm sounder (86 db) with remote annunciator connected to access control system. The unit shall operate on 12 or 24VAC or VDC. 1) Specified Manufacturers: Securitron PZ-1 6.
ELECTRIC POWER TRANSFER a. Power Transfer devices shall be provided with molex standardized plug connectors to accommodate up to twelve (12) wires. Plug connectors shall plug directly into molex through-door wiring harnesses for connection to electric locking devices and power supplies. Provide sufficient number of concealed wires to accommodate electric function of specified hardware. Install in door and frame edges. 1) Specified Manufacturer: McKinney 2) Approved Substitutes: Hager
K. MISC ACCESSORIES 1. REMODELER PLATES a. Manufactured from high quality prefinished 22 gauge steel in an approved finish appropriate for the installation. Finish shall be determined by Owner's Authorized Representative and Building Owner. 1) Specified Manufacturer: Don-Jo 2. WRAP AROUNDS a. Manufactured from high quality prefinished 22 gauge steel in an approved finish appropriate for the installation. Finish shall be determined by Owner's Authorized Representative and Building Owner. Field verification of door thickness required prior to ordering product. 1) Specified Manufacturer: Don-Jo
Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 12
DAS Contract Number R02331 HEA Job Number 10013
2.02
27 October 2014 Construction Documents
FINISHES
A. New hardware finishes should match the existing finishes of the surrounding door hardware. Where finishes vary they should match the prevailing finishes in the building. B. The designations used in schedules and elsewhere to indicate hardware finishes are those listed in ANSI/BHMA A156.18 or traditional U.S. finishes shown by certain manufacturers for their products. C. Provide quality of finish, including thickness of plating or coating (if any), composition, hardness, and other qualities complying with manufacturer's standards, but in no case less than specified by referenced standards for the applicable units of hardware. D. Where specified hardware shall have an antimicrobial coating which permanently suppresses the growth of bacteria, algae, fungus, mold and mildew applied. The finish shall control the spread and growth of bacteria, mold and mildew and shall be FDA listed for use in medical and food preparation equipment. PART III – EXECUTION 3.01
EXAMINATION
A. Contractor shall ensure that the building is secured and free from weather elements prior to installing interior door hardware. Examine hardware before installation to ensure it is free of defects. 3.02
INSTALLATION
A. Mount hardware units at heights indicated in the following applicable publications, except as specifically indicated or required to comply with the governing regulations. 1. “Recommended Locations for Builders Hardware for Standard Steel Doors and Frames” by the Door and Hardware Institute (DHI.) 2. WDMA Industry Standard I.S.1.7, “Hardware Locations for Wood Flush Doors.” 3. Provide blocking in drywall partitions where wall stops are to be located. B. All hardware shall be applied and installed in accordance with best trade practice by an experienced hardware installer. Care shall be exercised not to mar or damage adjacent work. C. Install each hardware item in compliance with the manufacturer's instructions and recommendations. Where cutting and fitting is required to install hardware onto or into surfaces that are later to be painted or finished in another way, coordinate removal, storage, Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 13
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
and reinstallation or application of surface protection with finishing work specified in the Division 1 Sections. Do not install surface-mounted items until finishes have been completed on the substrates involved. D. Provide a secure lock up for hardware delivered to the project but not yet installed. Control the handling and installation of hardware items so that the completion of the work will not be delayed by hardware losses before and after installation. 3.03
FIELD QUALITY CONTROL
A. The Contractor shall comply with AIA A201 1997 section 3.3.1 which reads as follows: “The Contractor shall be solely responsible for and have control over construction means, methods, techniques, sequences and procedures and for coordinating all portions of the Work under the Contract, unless the contract Documents give other specific instructions concerning these matters.” B. The hardware supplier shall do a final inspection prior to building completion to ensure that all hardware was correctly installed and is in proper working order. 3.04
ADJUSTING, CLEANING, AND DEMONSTRATING
A. Adjust and check each operating item of hardware and each door to ensure proper operation or function of every unit. Replace units that cannot be adjusted to operate freely and smoothly or as intended for the application made. B. Where door hardware is installed more than one month prior to acceptance or occupancy of a space or area, return to the installation during the week prior to acceptance or occupancy and make final check and adjustment of all hardware items in such space or area. Clean operating items as necessary to restore to proper function and finish of hardware and doors. Adjust door control devices to compensate for final operation of heating and ventilating equipment. C. Instruct owner's personnel in the proper adjustment and maintenance of door hardware and hardware finishes and usage of any electronic devices. 3.05
PROTECTION
A. Contractor shall protect all hardware, as it is stored on construction site in a covered and dry place. Protect exposed hardware installed on doors during the construction phase. Install any and all hardware at the latest possible time frame. 3.06
HARDWARE GROUPS
A. The hardware groups in section 087101 are furnished for whatever assistance it may afford the Contractor; do not consider it as entirely inclusive. Should any particular door item be Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 14
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
omitted in any group, provide door item with hardware same as required for similar purposes. Hardware supplier is responsible for handing and sizing all products as listed in the hardware heading. Quantities listed are for each pair of doors, or for each single door. END OF SECTION
Region 1 – Midwest Oregon Courts Security Systems Upgrades
DOOR HARDWARE 087100 15
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 087101 HARDWARE GROUPS HW GROUP: 1 1 Proximity Card Reader See Section 281300 1 Door Contact See Section 281300 1 Electric Cylindrical Lockset See Section 087100 Finish to match existing Integral Request to Exit (REX). Heavy duty, commercial, continuous duty locking hardware intended for security control. Fail Secure unless egress requires Fail Safe. 1 Power Supply; for Cylindrical Lock See Section 087100 1 120v hookup for power supply 1 Power Transfer Hinge See Section 087100 Finish to match existing 2 Remodeler Plate See Section 087100 Finish to match existing NOTE: See Electrical equipment schedule for card reader and access control system. Provide power supplies, Junction boxes, terminations any and all miscellaneous items required to make a complete and working Access Control system, as described in these specifications. Install wiring, conduit, and conductors to make a complete and working Access Control system, as described in these specifications. Remodeler plate minimum size to be 4" x 14". Plate to cover all existing/unused door hardware holes. Field verify coverage area to insure a clean appearance. Balance of hardware existing, clean and adjust to ensure proper function. HW GROUP: 2 1 Proximity Card Reader See Section 281300 1 Door Contact See Section 281300 1 Electric Cylindrical Lockset See Section 087100 Finish to match existing Integral Request to Exit (REX). Heavy duty, commercial, continuous duty locking hardware intended for security control. Fail Secure unless egress requires Fail Safe. 1 Power Supply; for Cylindrical Lock See Section 087100 1 120v hookup for power supply 1 Power Transfer Hinge See Section 087100 Finish to match existing 1 Closer See Section 087100 Finish to match existing NOTE: See Electrical equipment schedule for card reader and access control system. Provide power supplies, Junction boxes, terminations any and all miscellaneous items required to make a complete and working Access Control system, as described in these specifications. Install wiring, conduit, and conductors to make a complete and working Access Control system, as described in these specifications. Balance of hardware existing, clean and adjust to ensure proper function. Region 1 – Midwest Oregon Courts Security Systems Upgrades
HARDWARE GROUPS 087101 1
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
HW GROUP: 3 1 Proximity Card Reader See Section 281300 1 Door Contact See Section 281300 1 Cylindrical Lockset See Section 087100 Finish to match existing Heavy duty, commercial, continuous duty locking hardware intended for security control. 1 REX (Request to Exit) 1 Electric Strike See Section 087100 Finish to match existing Fail Secure unless egress requires Fail Safe. 1 Power Supply; for Electric Strike/REX See Section 087100 1 120v hookup for power supply 1 Closer See Section 087100 Finish to match existing NOTE: See Electrical equipment schedule for card reader and access control system. Provide power supplies, Junction boxes, terminations any and all miscellaneous items required to make a complete and working Access Control system, as described in these specifications. Install wiring, conduit, and conductors to make a complete and working Access Control system, as described in these specifications. Balance of hardware existing, clean and adjust to ensure proper function. HW GROUP: 4 1 Proximity Card Reader See Section 281300 1 Door Contact See Section 281300 1 Mortise Lockset See Section 087100 Finish to match existing Heavy duty, commercial, continuous duty locking hardware intended for security control. 1 REX (Request to Exit) 1 Electric Strike See Section 087100 Finish to match existing Fail Secure unless egress requires Fail Safe. 1 Power Supply; for Electric Strike/REX See Section 087100 1 120v hookup for power supply 2 Remodeler Plate See Section 087100 Finish to match existing NOTE: See Electrical equipment schedule for card reader and access control system. Provide power supplies, Junction boxes, terminations any and all miscellaneous items required to make a complete and working Access Control system, as described in these specifications. Install wiring, conduit, and conductors to make a complete and working Access Control system, as described in these specifications. Remodeler plate minimum size to be 4" x 14". Plate to cover all existing/unused door hardware holes. Field verify coverage area to insure a clean appearance. Balance of hardware existing, clean and adjust to ensure proper function. HW GROUP: 5 NOT USED
Region 1 – Midwest Oregon Courts Security Systems Upgrades
HARDWARE GROUPS 087101 2
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
HW GROUP: 6 Same as Hardware Group 2, except without closer. HW GROUP: 7 1 Proximity Card Reader See Section 281300 1 Door Contact See Section 281300 1 Electric Cylindrical Lockset See Section 087100 Finish to match existing Integral Request to Exit (REX). Heavy duty, commercial, continuous duty locking hardware intended for security control. Fail Secure unless egress requires Fail Safe. 1 Power Supply; for Cylindrical Lock See Section 087100 1 120v hookup for power supply 1 Power Transfer Hinge See Section 087100 Finish to match existing 1 Closer See Section 087100 Finish to match existing 1 Wrap Around See Section 087100 Finish to match existing NOTE: See Electrical equipment schedule for card reader and access control system. Provide power supplies, Junction boxes, terminations any and all miscellaneous items required to make a complete and working Access Control system, as described in these specifications. Install wiring, conduit, and conductors to make a complete and working Access Control system, as described in these specifications. Balance of hardware existing, clean and adjust to ensure proper function. Verify door thickness for wrap around. HW GROUP: 8 1 Proximity Card Reader See Section 281300 1 Door Contact See Section 281300 1 Electric Mortise Lockset See Section 087100 Finish to match existing Integral Request to Exit (REX). Heavy duty, commercial, continuous duty locking hardware intended for security control. Fail Secure unless egress requires Fail Safe. 1 Power Supply; for Mortise Lock See Section 087100 1 120v hookup for power supply 1 Power Transfer Hinge See Section 087100 Finish to match existing 1 Closer See Section 087100 Finish to match existing 2 Remodeler Plate See Section 087100 Finish to match existing NOTE: See Electrical equipment schedule for card reader and access control system. Provide power supplies, Junction boxes, terminations any and all miscellaneous items required to make a complete and working Access Control system, as described in these specifications. Install wiring, conduit, and conductors to make a complete and working Access Control system, as described in these specifications. Balance of hardware existing, clean and adjust to ensure proper function. Region 1 – Midwest Oregon Courts Security Systems Upgrades
HARDWARE GROUPS 087101 3
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
HW GROUP: 9 Same as Hardware Group 3, except without closer. HW GROUP: 10 1 Proximity Card Reader See Section 281300 1 Door Contact See Section 281300 1 Electric Cylindrical Lockset See Section 087100 Finish to match existing Integral Request to Exit (REX). Heavy duty, commercial, continuous duty locking hardware intended for security control. Fail Secure unless egress requires Fail Safe. 1 Power Supply; for Cylindrical Lock See Section 087100 1 120v hookup for power supply 1 Power Transfer Hinge See Section 087100 Finish to match existing 1 Closer See Section 087100 Finish to match existing NOTE: See Electrical equipment schedule for card reader and access control system. Provide power supplies, Junction boxes, terminations any and all miscellaneous items required to make a complete and working Access Control system, as described in these specifications. Install wiring, conduit, and conductors to make a complete and working Access Control system, as described in these specifications. Existing door opening is a double door with Right Hand door leaf receiving hardware as noted above. Balance of hardware existing, clean and adjust to ensure proper function. HW GROUP: 11 1 Proximity Card Reader See Section 281300 1 Door Contact See Section 281300 1 Magnetic Lock See Section 081700 1 Emergency Exit Button See Section 087100 Mount with-in 5'-0" of door at a height of 44" AFF. 1 Alarm Sounder See Section 087100 Mount at a height of 44" AFF. Alarm Sounder to interface with Access Control system. 1 Power Supply; for Exit Button/Sounder and Magnetic Lock See Section 087100 1 120v hookup for power supply NOTE: See Electrical equipment schedule for card reader and access control system. Provide power supplies, Junction boxes, terminations any and all miscellaneous items required to make a complete and working Access Control system, as described in these specifications. Install wiring, conduit, and conductors to make a complete and working Access Control system, as described in these specifications. Balance of hardware existing, clean and adjust to ensure proper function. Region 1 – Midwest Oregon Courts Security Systems Upgrades
HARDWARE GROUPS 087101 4
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
HW GROUP: 12 1 Proximity Card Reader See Section 281300 1 Door Contact See Section 281300 1 Cylindrical Lockset See Section 087100 Finish to match existing Heavy duty, commercial, continuous duty locking hardware intended for security control. 1 Magnetic Lock See Section 087100 1 Emergency Exit Button See Section 087100 Mount with-in 5'-0" of door at a height of 44" AFF. 1 Alarm Sounder See Section 087100 Mount at a height of 44" AFF. Alarm Sounder to interface with Access Control system. 1 Power Supply; for Exit Button/Sounder and Magnetic Lock See Section 087100 1 120v hookup for power supply NOTE: See Electrical equipment schedule for card reader and access control system. Provide power supplies, Junction boxes, terminations any and all miscellaneous items required to make a complete and working Access Control system, as described in these specifications. Install wiring, conduit, and conductors to make a complete and working Access Control system, as described in these specifications. Balance of hardware existing, clean and adjust to ensure proper function. HW GROUP: 13 Same as Hardware Group 8, except without closer NOTE: Existing door opening is within a concrete masonry wall. HW GROUP: 14 Polk County Courthouse – Jail Building, Second Floor Door: Courtroom #4 to Chambers. 1 Deadbolt Interchangeable core Thumbturn on inside 1 Strike 1 Dust Box Reinforcer HW GROUP: 15 1 Proximity Card Reader 1 Door Contact 1 Magnetic Cabinet Lock 1 Door Release Button 1 Power Supply; for Magnetic Lock and Door Release
See Section 281300 See Section 281300 See Section 087100 See Section 087100 See Section 087100
END OF SECTION Region 1 – Midwest Oregon Courts Security Systems Upgrades
HARDWARE GROUPS 087101 5
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
SECTION 099000 PAINT AND COATINGS PART
1
GENERAL
1.01 SECTION INCLUDES A. Surface preparation. B. Field application of paints. C. Scope: Finish surfaces of the work exposed to view. D. Do Not Paint or Finish the Following Items: 1. Items fully factory-finished unless specifically so indicated; materials and products having factory-applied primers are not considered factory finished. 2. Items indicated to receive other finishes. 3. Items indicated to remain unfinished. 4. Fire rating labels, equipment serial number and capacity labels, and operating parts of equipment. 5. Non-metallic roofing and flashing. 6. Stainless steel, anodized aluminum, bronze, and lead items. 7. Marble, granite, slate, and other natural stones. 8. Floors. 9. Ceramic and other tiles. 10. Glass. 11. Acoustical materials, unless specifically so indicated. 12. Exposed and Concealed pipes, ducts, and conduits. 13. Existing wood trusses, rafters and other wood elements, unless otherwise noted. 1.02 RELATED REQUIREMENTS A. See State of Oregon General Conditions for Public Improvement Contracts – Section F: Job Site conditions B. Section 017000 – Execution and Closeout Requirements: For cutting and patching of work. 1.03 DEFINITIONS A. Conform to ASTM D 16 for interpretation of terms used in this section. 1.04 REFERENCE STANDARDS A. ASTM D 16 - Standard Terminology for Paint, Related Coatings, Materials, and Applications; 2007. B.
ASTM D 4442 - Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials; 1992 (Reapproved 2003).
C.
GreenSeal GS-11 - Paints; 1993.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
PAINT AND COATINGS 099000- 1
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
1.05 SUBMITTALS A.
See State of Oregon General Conditions for Public Improvement Contracts - Administration of the Contract, for submittal procedures.
B.
Product Data: Provide data on all finishing products, including VOC content.
C.
Certification: By manufacturer that all paints and coatings do not contain any of the prohibited chemicals specified; GreenSeal GS-11 certification is not required but if provided shall constitute acceptable certification.
D.
Maintenance Data: Submit data on cleaning, touch-up, and repair of painted and coated surfaces.
E.
Maintenance Materials: Furnish the following for Owner's use in maintenance of project. 1. See Section 016000 - Product Requirements, for additional provisions. 2. Extra Paint and Coatings: 1 pint of each color; store where directed. 3. Label each container with color in addition to the manufacturer's label.
1.06 QUALITY ASSURANCE A.
Manufacturer Qualifications: Company specializing in manufacturing the products specified, with minimum three years documented experience.
B.
Applicator Qualifications: Company specializing in performing the type of work specified approved by manufacturer.
1.07 DELIVERY, STORAGE, AND HANDLING A.
Deliver products to site in sealed and labeled containers; inspect to verify acceptability.
B.
Container Label: Include manufacturer's name, type of paint, brand name, lot number, brand code, coverage, surface preparation, drying time, cleanup requirements, color designation, and instructions for mixing and reducing.
C.
Paint Materials: Store at minimum ambient temperature of 45 degrees F and a maximum of 90 degrees F, in ventilated area, and as required by manufacturer's instructions.
1.08 FIELD CONDITIONS A.
Do not apply materials when surface and ambient temperatures are outside the temperature ranges required by the paint product manufacturer.
B.
Follow manufacturer's recommended procedures for producing best results, including testing of substrates, moisture in substrates, and humidity and temperature limitations.
C.
Minimum Application Temperatures for Latex Paints: 45 degrees F for interiors; 50 degrees F for exterior; unless required otherwise by manufacturer's instructions.
PART 2 PRODUCTS 2.01 MANUFACTURERS A.
Provide all paint and coating products from the same manufacturer to the greatest extent possible.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
PAINT AND COATINGS 099000- 2
DAS Contract Number R02331 HEA Job Number 10013
B.
27 October 2014 Construction Documents
Approved Paints: 1. Miller Paint Company: www.millerpaint.com. 2. Duron, Inc: www.duron.com. 3. ICI Paints: www.icipaintsinna.com. 4. Benjamin Moore & Co: www.benjaminmoore.com. 5. PPG Architectural Finishes, Inc: www.ppgaf.com. 6. Or an approved substitution.
2.02 PAINTS AND COATINGS - GENERAL A.
Paints and Coatings: Ready mixed, unless intended to be a field-catalyzed coating. 1. Provide paints and coatings of a soft paste consistency, capable of being readily and uniformly dispersed to a homogeneous coating, with good flow and brushing properties, and capable of drying or curing free of streaks or sags. 2. Provide materials that are compatible with one another and the substrates indicated under conditions of service and application, as demonstrated by manufacturer based on testing and field experience. 3. For opaque finishes, tint each coat including primer coat and intermediate coats, onehalf shade lighter than succeeding coat, with final finish coat as base color. 4. Supply each coating material in quantity required to complete entire project's work from a single production run. 5. Do not reduce, thin, or dilute coatings or add materials to coatings unless such procedure is specifically described in manufacturer's product instructions.
B.
Primers: Where the manufacturer offers options on primers for a particular substrate, use primer categorized as "best" by the manufacturer.
C.
1. Provide coatings that comply with the most stringent requirements specified in the following: a. 40 CFR 59, Subpart D--National Volatile Organic Compound Emission Standards for Architectural Coatings. b. Ozone Transport Commission (OTC) Model Rule, Architectural, Industrial, and Maintenance Coatings; www.otcair.org; specifically: 1) Opaque, Flat: 50 g/L, maximum. 2) Opaque, Nonflat: 150 g/L, maximum. 3) Opaque, High Gloss: 250 g/L, maximum. 4) Varnishes: 350 g/L, maximum. c. Architectural coatings VOC limits of State in which the project is located.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
PAINT AND COATINGS 099000- 3
DAS Contract Number R02331 HEA Job Number 10013
2.
3.
27 October 2014 Construction Documents
Determination of VOC Content: Testing and calculation in accordance with 40 CFR 59, Subpart D (EPA Method 24), exclusive of colorants added to a tint base and water added at project site; or other method acceptable to authorities having jurisdiction. Evidence of Compliance: Acceptable types of evidence are: a. Report of laboratory testing performed in accordance with requirements. b. Published product data showing compliance with requirements. c. Certification by manufacturer that product complies with requirements.
D.
Chemical Content: The following compounds are prohibited: 1. Aromatic Compounds: In excess of 1.0 percent by weight of total aromatic compounds (hydrocarbon compounds containing one or more benzene rings). 2. Acrolein, acrylonitrile, antimony, benzene, butyl benzyl phthalate, cadmium, di (2ethylhexyl) phthalate, di-n-butyl phthalate, di-n-octyl phthalate, 1,2-dichlorobenzene, diethyl phthalate, dimethyl phthalate, ethylbenzene, formaldehyde, hexavalent chromium, isophorone, lead, mercury, methyl ethyl ketone, methyl isobutyl ketone, methylene chloride, naphthalene, toluene (methylbenzene), 1,1,1-trichloroethane, vinyl chloride.
E.
Flammability: Comply with applicable code for surface burning characteristics.
F.
Colors: 1. Paint to edge or natural break in surface, or as directed by Architect.
2.03 PAINT SYSTEMS A.
Paint Systems 1. Match existing painted surfaces.
2.04 ACCESSORY MATERIALS A.
Accessory Materials: Provide all primers, sealers, cleaning agents, cleaning cloths, sanding materials, and clean-up materials required to achieve the finishes specified whether specifically indicated or not; commercial quality.
B.
Patching Material: Latex filler.
C.
Fastener Head Cover Material: Latex filler.
PART 3 EXECUTION 3.01 EXAMINATION A.
Do not begin application of coatings until substrates have been properly prepared.
B.
Verify that surfaces are ready to receive work as instructed by the product manufacturer.
C.
Examine surfaces scheduled to be finished prior to commencement of work. Report any condition that may potentially affect proper application.
D.
If substrate preparation is the responsibility of another installer, notify Architect of
Region 1 - Midwest Oregon Courts Security Systems Upgrades
PAINT AND COATINGS 099000- 4
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
unsatisfactory preparation before proceeding. E.
Test shop-applied primer for compatibility with subsequent cover materials.
3.02 PREPARATION A.
Clean surfaces thoroughly and correct defects prior to coating application.
B.
Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
C.
Remove or repair existing coatings that exhibit surface defects in and around patched areas.
D.
Remove or mask surface appurtenances, including electrical plates, hardware, light fixture trim, escutcheons, and fittings, prior to preparing surfaces or finishing.
E.
Seal surfaces that might cause bleed through or staining of topcoat.
F.
Concrete and Unit Masonry Surfaces to be Painted: Surface must be clean, dry and free of grease, dust, or loose particles.
G. Gypsum Board Surfaces to be Painted: Apply primer coat over entire patched area. Cover area a minimum of 1-inch beyond patch area. Allow primer to dry for two to four hours, or according to manufacturer's recommendations. H.
Plaster Surfaces to be Painted: Allow plaster patched area to dry fully before applying primer and finish coats. Prime repair area after repair. Cover area a minimum of 1-inch beyond patch area. Allow primer to dry for two to four hours, or according to manufacturer's recommendations.
I.
Insulated Coverings to be Painted: Remove dirt, grease, and oil from canvas and cotton.
3.03 APPLICATION A.
Employ workers skilled in the application of paint products specified.
B.
Except where method of application is specifically noted, all materials shall be applied by brush or roller.
C.
Drying: Apply paints to surfaces at atmospheric temperatures of not less than 50°F and maintain this minimum temperature throughout the drying time. Ensure adequate ventilation in all painted spaces. Allow sufficient time to elapse as recommended by the manufacturer, between successive coats, to permit proper drying. Modify as necessary to suit adverse weather conditions.
D.
Interior: 1. Gypsum Board: Apply one prime coat and two finish coats of material specified above. 2. Veneer Plaster and Concrete Block: Apply one prime coat and two finish coats of material specified above.
E.
Apply products in accordance with manufacturer's instructions.
F.
Where adjacent sealant is to be painted, do not apply finish coats until sealant is applied.
Region 1 - Midwest Oregon Courts Security Systems Upgrades
PAINT AND COATINGS 099000- 5
DAS Contract Number R02331 HEA Job Number 10013
27 October 2014 Construction Documents
G. Do not apply finishes to surfaces that are not dry. Allow applied coats to dry before next coat is applied. H.
Apply each coat to uniform appearance.
I.
Dark Colors and Deep Clear Colors: Regardless of number of coats specified, apply as many coats as necessary for complete hide.
J.
Vacuum clean surfaces of loose particles. Use tack cloth to remove dust and particles just prior to applying next coat.
K.
Reinstall electrical cover plates, hardware, light fixture trim, escutcheons, and fittings removed prior to finishing.
3.05 CLEANING A.
Collect waste material that could constitute a fire hazard, place in closed metal containers, and remove daily from site.
3.05 PROTECTION A.
Protect finished coatings until completion of project.
B.
Touch-up damaged coatings after Substantial Completion.
END OF SECTION
Region 1 - Midwest Oregon Courts Security Systems Upgrades
PAINT AND COATINGS 099000- 6
SECTION 26 05 01 ELECTRICAL DEMOLITION PART 1 GENERAL 1.01 SECTION INCLUDES A.
Electrical demolition.
1.02 RELATED REQUIREMENTS A.
See State of Oregon General Conditions for Public Improvements Contracts drawings and Section 02 41 00 for additional requirements for alterations work.
PART 2 PRODUCTS 2.01 MATERIALS AND EQUIPMENT A.
Materials and equipment for patching and extending work: As specified in individual sections.
PART 3 EXECUTION 3.01 EXAMINATION A.
Verify field measurements and circuiting arrangements.
B.
Verify that abandoned wiring and equipment serve only abandoned facilities.
C.
Information given on the drawings in reference to existing features has been obtained from recent field observation and existing record documents, but cannot be guaranteed to be completely accurate in all respects. Verify all information before proceeding with any work.
D.
Report discrepancies between the drawings and actual conditions to Architect before disturbing existing installation.
E.
Beginning of demolition means installer accepts existing conditions.
3.02 PREPARATION A.
Disconnect electrical systems and remove devices in walls, floors, and ceilings to be removed.
B.
Coordinate disruption of power, access control, duress, and video surveillance systems with Owner prior to disruption of any system.
C.
Provide temporary wiring and connections to maintain existing systems, as may be required by Architect or Owner, in service during construction. When work must be performed on energized equipment or circuits, use personnel experienced in such operations.
D.
Existing Access, Video Surveillance, and Duress Cabling Systems: Maintain existing system in service until new system is complete and ready for service or new system is accepted. Disable system only to make switchovers and connections. Minimize outage duration. 1. Notify/obtain permission from Architect at least 7 days before partially or completely disabling system. 2. Make temporary connections to maintain service in areas adjacent to work area. 3. Additional expense due to scheduling or coordination will be borne by Contractor.
E.
The Contractor shall visit and become thoroughly familiar with the existing conditions prior to bidding.
F.
Coordinate work of Division 26 with that of other divisions prior to rough-in.
G.
All existing electrical systems, including but not limited to conduit and wiring, which are not to be demolished shall be protected from damage during the demolition and construction phases. Systems shall be operational in a manner consistent with the phasing plan and construction schedule.
3.03 DEMOLITION AND EXTENSION OF EXISTING ELECTRICAL WORK A.
Remove, relocate, and extend existing installations to accommodate new system components.
B.
Remove abandoned wiring to source of supply, including existing wiring that has been previously abandoned in place.
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 01 - 1
ELECTRICAL DEMOLITION
C.
Remove exposed abandoned cables and conduit, including abandoned conduit above accessible ceiling finishes. Cut conduit flush with walls and floors, and patch surfaces. Seal all abandoned conduit.
D.
Disconnect and remove electrical devices and equipment serving utilization equipment that has been removed.
E.
Repair adjacent construction and finishes damaged during demolition and extension work.
F.
Maintain access to existing electrical installations which remain active. Modify installation or provide access panels as appropriate.
G.
All labor and materials required to change the existing electrical installation as indicated shall be provided. Drawings are diagrammatic and do not show all existing interconnecting components.
H.
The Contractor shall have the option to reuse existing raceways as far as practical, provided it remains code accessible, concealed by new work, and not in conflict with demolition.
I.
All abandoned Class 2, Class 3, and PLTC cables are to be removed in accordance with Article 725 of NEC.
3.04 CLEANING AND REPAIR A.
Clean and repair existing materials and equipment that remain or that are to be reused.
B.
Owner shall have first right of salvage of any and all electrical materials and equipment intended for demolition. Items not salvaged by the Owner shall become the property of the Contractor and shall be removed from the site.
C.
Refer to Section 01 70 00 Execution and Closeout Requirements for cutting and patching requirements. END OF SECTION 26 05 01
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 01 - 2
ELECTRICAL DEMOLITION
SECTION 26 05 05 GENERAL ELECTRICAL REQUIREMENTS PART 1 GENERAL 1.01 SECTION INCLUDES A.
Design and installation requirements for electrical and low voltage systems specified in Divisions 26, 27, and 28.
B.
Design requirements for installation and connection of equipment specified in other divisions of specification.
1.02 REFERENCES A.
NECA 1 - Standard for Good Workmanship in Electrical Contracting; National Electrical Contractors Association; 2010.
B.
NETA STD ATS - Acceptance Testing Specifications for Electrical Power Distribution Equipment and Systems; International Electrical Testing Association; 2009.
1.03 SUBMITTALS A.
Design Drawings and Product Submittals: 1. Submit in accordance with State of Oregon General Conditions for Public Improvements Contracts and Section 01 30 00 on proposed materials and equipment. In addition, provide design drawings as outlined in Design Approach and Requirements below. 2. Verify that submitted equipment can be delivered and installed within the time constraints of the construction period. 3. Include conduit sleeving, wire run, and connection diagram for signal and low voltage systems. 4. Call to the attention of the Architect any deviations, discrepancies or conflicts between the design drawings, specifications and contract documents when data is submitted. 5. Design drawing submittals processed by the Architect are not change orders. The submittal process is a means to determine quality control and to demonstrate to the Architect that the Contractor understands the design concept. 6. These drawings will also be reviewed by the Owner's electrical engineer for conformance to specifications. 7. Include photos taken at pre-construction walk-through.
B.
Samples: Submit samples as requested by the Architect.
1.04 PROJECT RECORD DOCUMENTS A.
Provide record project documents in accordance with State of Oregon General Conditions for Public Improvements Contracts.
B.
Maintain one "work" set on project site. Work set is subject to inspection by the Architect.
C.
Show variation from the contract documents and exact routing of conduits and all cable associated with installation of access, video surveillance, and duress systems.
1.05 QUALITY ASSURANCE A.
Work and materials to conform to applicable local and state codes, and federal, state and other applicable laws and regulations.
B.
Provide equipment and materials labeled or listed by the Underwriters Laboratory, Inc. (U.L.) or other accepted qualified testing laboratories.
C.
Whenever the requirements of the specifications or drawings exceed those of the applicable code or standard, the requirements of the specifications or drawings to govern.
D.
The specifications and drawings are complementary. What is called for by one to be as though called for by both.
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 05 - 1
GENERAL ELECTRICAL REQUIREMENTS
PART 2 PRODUCTS 2.01 PROJECT REQUIREMENTS A.
The project includes: 1. Design, furnishing, and installation of access control, video surveillance, and duress systems. 2. Provide necessary drawings, calculations, and backup materials required to obtain permits for installation of access control, video surveillance, and duress systems.
2.02 DESIGN APPROACH AND REQUIREMENTS A.
Use this specifications and drawings as a guide for workmanship and materials or construction. The specifications and drawings are based on general observations of the existing security equipment. The Contractor shall provide detailed examination of existing security equipment and detailed design drawings based on the concepts specified herein. This approach shall be utilized through completion of the project.
B.
Visit the site of proposed construction prior to submitting proposal. Verify and inspect the existing site to determine conditions that affect this work. Only areas that are normally accessible to the public will be available during the bid.
C.
The bidders to ascertain the requirements of the service utilities, including phone and off-site monitoring agencies, and be apprised of the applicable code, rules, and regulations as enforced by authorities having jurisdiction prior to bid.
D.
Provide 120V power as required for door locks, power supplies, equipment racks, etc., as required to complete all systems.
E.
Provide rough-in and 120-volt power connections for access control, video surveillance, and duress systems. Coordinate panel locations and circuit numbers with Building Owner. Security equipment shall be connected to dedicated 20 amp, 120 volt circuits, other loads may no be connected to said circuit(s).
F.
Locate, design, and installation of power connections as noted throughout the specifications and as needed to power all new equipment.
G.
Relocate devices up to 20 feet from location shown on drawings without additional cost to Owner.
H.
Prior to preparation of design/shop drawings by Contractor, a walk-through of each facility will take place. Contractor, Owner, Building Owner, Owner's project manager, Owner's authorized representative, and Owner's hazardous materials consultant will be in attendance. Contractor shall: 1. Propose exact location of every device and control panel, and document by placing a Post-It note with the device number and room name and taking a photograph. 2. Propose general wiring routes to team (including Owner's hazardous materials consultant). 3. Obtain all field verification required to prepare design/shop drawings.
2.03 CONSTRUCTION DRAWINGS A.
Provide complete 1/8-inch scale drawings showing device layout, interconnection diagrams, and schematic diagram for access control, video surveillance, and duress systems. Refer to Sections 28 13 00, 28 16 00, and 28 23 00 for additional requirements.
B.
Electronic floor plan backgrounds will be available from the Architect.
C.
Prepare drawings with electronic drawing program.
2.04 MANUFACTURERS A.
Material to be new and bear manufacturer's name, model number, electrical characteristics, UL label and other standard manufacturer identification.
B.
Indicated brand names and catalog numbers are used to establish standards of performance and quality. The description of materials listed govern in the event that catalog numbers do not correspond to the described materials.
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 05 - 2
GENERAL ELECTRICAL REQUIREMENTS
2.05 ACCESSORIES A.
Include special features, finishes, description, or requirements indicated in the contract documents for particular items or equipment, but not included by or in the item's listed catalog number.
B.
Furnish and install as part of the contract work incidentals, not specifically mentioned herein or noted on the drawings, but required to complete the system or systems, in a safe and satisfactory working condition, provided and installed as part of the contract work.
PART 3 EXECUTION 3.01 VERIFICATION A.
Visit the construction site prior to bidding to determine the conditions that affect the work in this division. Failure to visit the site does not relieve responsibility of performing work to provide a complete and operable facility.
B.
Include costs to complete the work described in the specifications and drawings based on the actual existing conditions.
3.02 CLARIFICATION A.
Call to the attention of the Architect any conflicts or discrepancies in the drawings or specifications prior to bid date. These items will be clarified by the Architect in Addendum form.
B.
Verify the physical dimensions of electrical equipment supplied to the project to insure that adequate mounting space is available. Notify the Architect of any conflicts prior to rough-in.
3.03 INSTALLATION A.
Provide raceways and conduits for electrical system wiring unless otherwise noted. Open wiring is permitted for limited energy low voltage systems as permitted by local codes and as noted. Low voltage wiring installed in return air plenum spaces to utilize plenum rated cable. Identify plenum spaces prior to bid.
B.
Where line voltage power wiring cannot be concealed, all exposed wiring shall be installed in surface metallic raceway in finished spaces with prior appoval from architect, and in conduit in unfinished spaces.
C.
Raceways and open wiring to be concealed where practical unless otherwise approved by the architect. Devices to be flush mounted unless otherwise noted. No exposed raceways shall be installed without prior approval from architect. Limited energy low voltage cable and MC power cable may be run open where it is fished into hollow walls and in accessible ceiling or accessible attic spaces.
D.
Where limited energy cable cannot be concealed, all exposed cable shall be installed in surface metallic raceway in finished spaces with prior approval from architect, or in conduit in unfinished spaces as noted below: 1. Regardless of height, where wiring must be run exposed in mechanical rooms and similar areas where the cable is subject to damage, cable shall be run in conduit. 2. Surface metallic raceway shall be used for horizontal runs below 9 feet and for all vertical runs where wiring cannot be concealed in all other spaces. 3. Cable may be run exposed in the horizontal direction where it is above 9 feet. Cable shall be run neat and parallel and perpendicular to structural lines. Make every effort to route cable to obscure its view by routing in corners and above other existing exposed utilities where present.
E.
Provide new wiring for all new devices and existing devices that are replaced with new, except existing limited energy cabling may be reused under the following conditions: 1. Where it is in good condition and is installed per applicable code. 2. Meets the requirements of the manufacturer of the respective equipment being installed. 3. Such that it will not be required to be spliced. 4. Where it is concealed or installed in a raceway, except existing exposed cabling may be reused where it is installed on furniture/casework for duress buttons.
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 05 - 3
GENERAL ELECTRICAL REQUIREMENTS
5.
Cable is tested and warranted as new cable.
F.
Provide machine printed wire tags of contrasting color at each end of every limited energy low voltage cable.
G.
Refer to drawings for locations where wiring exposed to view is explicitly not allowed. In these areas wiring must be concealed from view. Submit detailed wiring plan for review by the design team prior to installation in these areas. END OF SECTION 26 05 05
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 05 - 4
GENERAL ELECTRICAL REQUIREMENTS
SECTION 26 05 19 BUILDING WIRE AND CABLE PART 1 GENERAL 1.01 SECTION INCLUDES A.
Wiring connectors and connections.
1.02 REFERENCE STANDARDS A.
NEC 210.4(B) - Multiwire Branch Circuits - Disconnecting Means; National Electrical Code; 2008
B.
NECA 1 - Standard for Good Workmanship in Electrical Construction; National Electrical Contractors Association; 2010.
1.03 QUALITY ASSURANCE A.
Products: Furnish products listed and classified by Underwriters Laboratories Inc. as suitable for the purpose specified and indicated.
PART 2 PRODUCTS 2.01 WIRING REQUIREMENTS A.
Concealed Dry Interior Locations: Use only building wire in raceway or metal clad cable.
B.
Above Accessible Ceilings: Use only building wire in raceway or metal clad cable.
C.
Wet or Damp Interior Locations: Use only building wire in raceway.
D.
Exterior Locations: Use only building wire in raceway.
E.
Use stranded conductors for control circuits.
F.
Use conductor not smaller than 12 AWG for power circuits.
G.
MC Cable may be used for branch circuit wiring where permitted by Code and where it can be concealed.
2.02 WIRE MANUFACTURERS A.
Cerro Wire Inc: www.cerrowire.com.
B.
American Insulated Wire: www.leviton.com.
C.
Southwire Company: www.southwire.com.
D.
General Cable; www.generalcable.com.
E.
Substitutions: See State of Oregon General Conditions for Public Improvements Contracts.
2.03 BUILDING WIRE A.
Description: Single conductor insulated wire.
2.04 METAL CLAD CABLE A.
Description: Type MC.
PART 3 EXECUTION 3.01 EXAMINATION A.
Verify that raceway installation is complete and supported.
B.
Verify that field measurements are as indicated.
3.02 PREPARATION A.
Completely and thoroughly swab raceway before installing wire.
3.03 INSTALLATION A.
Install wire and cable securely, in a neat and workmanlike manner, as specified in NECA 1. Contractor shall comply with NEC 210.4(B) by providing a separate neutral conductor for each circuit in a multi-wire branch circuit.
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 19 - 1
BUILDING WIRE AND CABLE
B.
Protect exposed cable from damage.
C.
Support cables above accessible ceiling, using spring metal clips to support cables from structure or ceiling suspension system. Do not rest cable on ceiling panels. Do not attach cables to slack wires.
D.
Use suitable cable fittings and connectors.
E.
Neatly train and lace wiring inside boxes, equipment, and racks.
F.
Identify and color code wire and cable per building standard. Identify each conductor with its circuit number or other designation indicated.
G.
Conceal building wire and cabling within finsihed walls, ceilings and flooring. Where concealment is not possiblem notify the architect for approval of exposed wire and/or cable. END OF SECTION 26 05 19
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 19 - 2
BUILDING WIRE AND CABLE
SECTION 26 05 34 CONDUIT PART 1 GENERAL 1.01 SECTION INCLUDES A.
Conduit, fittings and conduit bodies for electrical systems.
B.
Conduit, fittings and conduit bodies for telecommunications systems.
1.02 REFERENCE STANDARDS A.
ANSI C80.3 - American National Standard for Steel Electrical Metallic Tubing (EMT); 2005.
B.
ANSI C80.6 - American National Standard for Electrical Intermediate Metal Conduit (EIMC); 2005.
C.
NECA 1 - Standard for Good Workmanship in Electrical Construction; National Electrical Contractors Association; 2010.
D.
NECA 101 - Standard for Installing Steel Conduits (Rigid, IMC, EMT); National Electrical Contractors Association; 2006.
E.
NEMA FB 1 - Fittings, Cast Metal Boxes, and Conduit Bodies for Conduit, Electrical Metallic Tubing, and Cable; National Electrical Manufacturers Association; 2012 (ANSI/NEMA FB 1).
1.03 SUBMITTALS A.
See State of Oregon General Conditions for Public Improvements Contracts for submittals procedures.
B.
Product Data: Provide for fittings and conduit bodies.
C.
Project Record Documents: Accurately record actual routing of all conduits.
1.04 QUALITY ASSURANCE A.
Products: Listed and classified by Underwriters Laboratories Inc. as suitable for purpose specified and shown.
1.05 DELIVERY, STORAGE, AND HANDLING A.
Accept conduit on site. Inspect for damage.
B.
Protect conduit from corrosion and entrance of debris by storing above grade. Provide appropriate covering.
PART 2 PRODUCTS 2.01 CONDUIT REQUIREMENTS A.
Conduit Size: 1. Minimum Size: 3/4 inch unless otherwise specified.
B.
Wet and Damp Locations: Use rigid steel conduit or intermediate metal conduit.
C.
Dry Locations: 1. Concealed: Use electrical metallic tubing. 2. Exposed where not subject to damage: Use electrical metallic tubing. 3. Exposed where subject to damage: Use rigid steel conduit or intermediate metal conduit.
D.
Maximum conduit fill for telecommunications systems cabling shall not exceed 40 percent.
2.02 METAL CONDUIT A.
Manufacturers: 1. Allied Tube & Conduit: www.alliedtube.com. 2. Wheatland Tube Company: www.wheatland.com. 3. Republic Conduit: www.republic-conduit.com.
B.
Intermediate Metal Conduit (IMC): Rigid steel, ANSI C80.6.
C.
Fittings and Conduit Bodies:
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 34 - 1
CONDUIT
1. 2. 3.
IMC shall be coupled and terminated with steel threaded fittings. Provide with nylon insulated bushings. Materials per NEMA FB 1.
2.03 FLEXIBLE METAL CONDUIT A.
Manufacturers: 1. AFC Cable Systems, Inc: www.afcweb.com. 2. International Metal Hose: www.metalhose.com. 3. KAF-TECH: www.kaf-tech.com.
B.
Description: Interlocked steel construction.
C.
Fittings: 1. Steel screw-in type connectors. 2. Couplings and set screw type connectors shall not be used. 3. Materials per NEMA FB 1.
2.04 ELECTRICAL METALLIC TUBING (EMT) A.
Manufacturers: 1. Allied Tube & Conduit: www.alliedeg.com. 2. Beck Manufacturing, Inc: www.beckmfg.com. 3. Wheatland Tube Company: www.wheatland.com. 4. Republic Conduit: www.republic-conduit.com.
B.
Description: ANSI C80.3; galvanized tubing.
C.
Fittings and Conduit Bodies: 1. Steel set screw type. 2. Provide with nylon insulated bushings. 3. Materials per NEMA FB 1.
PART 3 EXECUTION 3.01 EXAMINATION A.
Verify that field measurements are as shown on drawings.
B.
Verify routing and termination locations of conduit prior to rough-in.
C.
Conduit routing is shown on drawings in approximate locations unless dimensioned. Route as required to complete wiring system.
3.02 INSTALLATION A.
Provide raceways and conduits for access control, video surveillance, and duress systems. Open wiring is permitted for low voltage systems as permitted by local codes and where it can be concealed. Low voltage wiring installed in return air plenum spaces to utilize plenum rated cable.
B.
Install conduit securely, in a neat and workmanlike manner, as specified in NECA 1.
C.
Install steel conduit as specified in NECA 101.
D.
Install nonmetallic conduit in accordance with manufacturer's instructions.
E.
Arrange supports to prevent misalignment during wiring installation.
F.
Support conduit using coated steel or malleable iron straps, lay-in adjustable hangers, clevis hangers, and split hangers.
G.
Fasten conduit supports to building structure and surfaces.
H.
Do not support conduit with wire or perforated pipe straps. Remove wire used for temporary supports.
I.
Do not attach conduit to ceiling support wires.
J.
Arrange conduit to maintain headroom and present neat appearance.
K.
Route all above grade conduit parallel and perpendicular to walls.
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 34 - 2
CONDUIT
L.
Maintain adequate clearance between conduit and piping.
M. Maintain 12 inch clearance between conduit and surfaces with temperatures exceeding 104 degrees F. Maintain 12 inch clearance between non-metallic conduit with low voltage cable and power conductors. N.
Cut conduit square using saw or pipecutter; de-burr cut ends.
O.
Bring conduit to shoulder of fittings; fasten securely.
P.
Provide suitable fittings to accommodate expansion and deflection where conduit crosses seismic, control, and expansion joints.
Q.
Ground and bond conduit per NEC.
R.
Where conduit is shown stubbed into a telephone, computer or communication terminal area, conduit shall be stubbed up 6 inches below ceiling and terminated with insulating bushings.
S.
Communications system conduit run above the ceiling shall not be installed within 12 inches of a parallel run of current carrying conductors, transformers, feeder cables, motors, or lighting ballasts.
T.
All conduits after installation shall be doweled to insure that no debris or imperfections are within the run. All conduits shall be left clean, dry and unobstructed.
U.
Penetrations of Drywall Constructions: 1. Ensure that the sound control performance of structures be maintained in accordance with the drawings and specifications. All penetrations shall be installed in a manner that results in complete air tightness through structure. If a condition occurs where penetration of the structure by a conduit is not shown clearly on the drawings (or described in the specifications), the Contractor shall ask immediately for clarification of the method necessary to install the particular item.
3.03 INTERFACE WITH OTHER PRODUCTS A.
Install conduit to preserve fire resistance rating of partitions and other elements, using materials and methods specified in Section 07 84 00.
B.
To attenuate objectionable EMI and RFI signals, the audio and video system raceway groups shall maintain a specified minimum distance separation whenever possible within the constraints of the building's architecture. System conduit groups that run parallel with each other shall adhere to the following table of minimum distance separation:
Audio/Video Sub-System Microphone Line Speaker Video
Microphone Adjacent 6 inches 12 inches 12 inches
Line 6 inches Adjacent 6 inches 6 inches
Speaker 12 inches 12 inches Adjacent 6 inches
Video 12 inches 6 inches 6 inches Adjacent
C.
Video system conduit that runs parallel with AC power conduit shall be separated by at least 3 feet minimum.
D.
Video system conduit that runs across or perpendicular to AC power conduit shall be separated by at least 1 foot minimum.
E.
To attenuate objectionable EMI and RFI signals, the telecommunications system raceway and cable shall maintain a specified minimum distance separation whenever possible within the constraints of the building's architecture. Condition
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 34 - 3
Minimum Separation Distance
CONDUIT
Unshielded power lines or electrical equipment in proximity to open or nonmetal telecommunication pathways Unshielded power lines or electrical equipment in proximity to a grounded metal telecommunication conduit pathway Power lines enclosed in a grounded metal conduit (or equivalent shielding) in proximity to a grounded metal telecommunication conduit pathway Electrical motors, transformers, generators, frequency converters, and UPS systems
24 inches 12 inches 12 inches 47 inches
END OF SECTION 26 05 34
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 34 - 4
CONDUIT
SECTION 26 05 35 SURFACE RACEWAYS PART 1 GENERAL 1.01 SECTION INCLUDES 1.02 REFERENCE STANDARDS A.
NECA 1 - Standard for Good Workmanship in Electrical Construction; National Electrical Contractors Association; 2010.
B.
NFPA 70 - National Electrical Code; National Fire Protection Association; Most Recent Edition Adopted by Authority Having Jurisdiction, Including All Applicable Amendments and Supplements.
1.03 SUBMITTALS A.
See State of Oregon General Conditions for Public Improvements Contracts for submittal procedures.
B.
Product Data: Provide dimensions, knockout sizes and locations, materials, fabrication details, finishes, and accessories.
C.
Manufacturer's Instructions: Indicate application conditions and limitations of use stipulated by product testing agency specified under Quality Assurance. Include instructions for storage, handling, protection, examination, preparation, and installation of product.
D.
Project Record Documents: Accurately record actual routing of all surface metallic raceways.
1.04 QUALITY ASSURANCE A.
Maintain one copy of document on site.
B.
Manufacturer Qualifications: Company specializing in manufacturing products specified in this Section with minimum three years experience.
C.
Products: Furnish products listed and classified by Underwriters Laboratories Inc. as suitable for purpose specified and shown.
PART 2 PRODUCTS 2.01 MANUFACTURERS A.
Metal raceway: 1. The Wiremold Company: www.wiremold.com. 2. Hubbell: www.hubbell-premise.com. 3. Substitutions: See State of Oregon General Conditions for Public Improvements Contracts.
PART 3 EXECUTION 3.01 INSTALLATION A.
Install in accordance with manufacturer's instructions.
B.
Install raceways securely, in a neat and workmanlike manner, as specified in NECA 1.
C.
Use flat-head screws, clips, and straps to fasten raceway channel to surfaces. Mount plumb and level.
D.
Wireway Supports: Provide steel channel.
E.
Close ends of wireway and unused conduit openings.
F.
Ground and bond raceway per NEC.
G.
Use of surface metallic raceway is limited. Refer to Section 26 05 05 for description of where it is permitted. END OF SECTION 26 05 35
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 35 - 1
SURFACE RACEWAYS
SECTION 26 05 37 BOXES PART 1 GENERAL 1.01 SECTION INCLUDES 1.02 REFERENCE STANDARDS 1.03 SUBMITTALS A.
See State of Oregon General Conditions for Public Improvements Contracts for submittal procedures.
B.
Project Record Documents: Record actual locations and mounting heights of outlet, pull, and junction boxes on project record documents.
1.04 QUALITY ASSURANCE PART 2 PRODUCTS 2.01 MANUFACTURERS A.
Appleton Electric: www.appletonelec.com.
B.
Arc-Co./Division of Arcade Technology: www.arc-co.com.
C.
Raco: www.hubbell-raco.com.
D.
Bell: www.hubbell-bell.com.
E.
T&B: www.tnb.com.
F.
Cooper: www.cooperindustries.com.
G.
Hoffman: www.hoffmanonline.com.
H.
Substitutions: See State of Oregon General Conditions for Public Improvements Contracts.
PART 3 EXECUTION 3.01 EXAMINATION A.
Verify locations of floor boxes and outlets in offices and work areas prior to rough-in.
3.02 INSTALLATION A.
Install in locations as shown on Drawings and as required for splices, taps, wire pulling, and equipment connections.
B.
Coordinate installation of outlet boxes for connected equipment.
C.
Electrical boxes are shown on Drawings in approximate locations unless dimensioned. 1. Adjust box locations up to 10 feet if required to accommodate intended purpose and to conceal all raceways.
D.
Orient boxes to accommodate wiring device orientation.
E.
Install boxes to preserve fire resistance rating of partitions and other elements, using materials and methods specified in Section 07 84 00.
F.
Use flush mounting outlet box in finished areas.
G.
Provide separate boxes for emergency power and normal power systems.
H.
Provide separate boxes for line voltage and low voltage systems.
I.
Locate outlet boxes so that wall plates do not span different building finishes.
J.
Locate outlet boxes so that wall plates do not cross masonry joints.
K.
Do not install flush mounting box back-to-back in walls; provide minimum 6 inches separation and not in the same stud cavity.. 1. Provide minimum 24 inches separation in acoustic rated walls. 2. Provide minimum 24 inches separation in fire rated walls.
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 37 - 1
BOXES
L.
Secure flush mounting box to interior wall and partition studs. Accurately position to allow for surface finish thickness.
M. Install flush mounting box without damaging wall insulation or reducing its effectiveness. N.
Use adjustable steel channel fasteners for hung ceiling outlet box.
O.
Do not fasten boxes to ceiling support wires.
3.03 ADJUSTING A.
Adjust flush-mounting devices to make front flush with finished wall material.
B.
Install knockout closures in unused box openings.
3.04 CLEANING A.
Clean interior of boxes to remove dust, debris, and other material.
3.05 INTERFACE WITH OTHER PRODUCTS A.
Coordinate installation of outlet box with products furnished under other sections of these specifications.
B.
Coordinate locations and sizes of required access doors. END OF SECTION 26 05 37
DAS Courts Sec Systems Reg 1 / HE-3206.6 26 05 37 - 2
BOXES
SECTION 27 10 05 LOW-VOLTAGE CABLING PATHWAYS PART 1 GENERAL 1.01 SECTION INCLUDES A.
Pathways inside building(s).
B.
Enclosures, backboards, and outlet boxes.
C.
Grounding and bonding the access control, video surveillance, and duress distribution systems.
1.02 RELATED REQUIREMENTS A.
Section 26 05 34 - Conduit.
B.
Section 26 05 37 - Boxes.
1.03 REFERENCE STANDARDS A.
EIA-310 - Cabinets, Racks, Panels, and Associated Equipment; Electronic Industries Association; Revision D, 1992.
B.
CEA-310 - Cabinets, Racks, Panels, and Associated Equipment; Consumer Electronics Association; Revision E, 2005.
C.
NFPA 70 - National Electrical Code; Most Recent Edition Adopted by Authority Having Jurisdiction, Including All Applicable Amendments and Supplements.
D.
TIA-568-C.1 - Commercial Building Telecommunications Cabling Standard; Telecommunications Industry Association; Rev C, 2009 (with Addenda; 2012).
E.
TIA-568-C.2 - Commercial Building Telecommunications Cabling Standard - Part 2: Balanced Twisted Pair Cabling Components; Telecommunications Industry Association; Rev C, 2009.
F.
TIA-569-C - Telecommunications Pathways and Spaces; Telecommunications Industry Association; Rev C, 2012 (with Addenda; 2013).
G.
TIA-606-B - Administration Standard for the Telecommunications Infrastructure; Telecommunications Industry Association; Rev B, 2012.
H.
ANSI/J-STD-607 - Commercial Building Grounding (Earthing) and Bonding Requirements for Telecommunications; Rev A, 2002.
I.
UL 514C - Nonmetallic Outlet Boxes, Flush-Device Boxes, and Covers; Current Edition, Including All Revisions.
1.04 DELIVERY, STORAGE, AND HANDLING A.
Store products in manufacturer's unopened packaging until ready for installation.
B.
Keep stored products clean and dry.
1.05 WARRANTY A.
See State of Oregon General Conditions for Public Improvements Contracts for additional warranty requirements.
B.
Correct defective Work within a 1 year period after Date of Substantial Completion.
PART 2 PRODUCTS 2.01 SYSTEM DESIGN A.
Provide a complete permanent system of cable pathways for voice and data communications, including conduits and wireways, pull wires, support structures, enclosures and cabinets, rough-in boxes, and conduit sleeves. 1. Comply with TIA/EIA-568 and TIA/EIA-569, latest editions. 2. Provide pathways that comply with ANSI/J-STD-607 and are UL listed or third party independent testing laboratory certified. 3. In this project, the term plenum is defined as return air spaces above ceilings, inside ducts, under raised floors, and other air-handling spaces.
DAS Courts Sec Systems Reg 1 / HE-3206.6 27 10 05 - 1
LOW-VOLTAGE CABLING PATHWAYS
4.
Conduit fill shall not exceed 30% of cross-sectional area of conduit.
2.02 PATHWAYS A.
Conduit: As specified in Section 26 05 34; provide pull cords in all conduit.
2.03 OUTLET BOXES A.
For flush mounting in walls; depth as required to accommodate cable manufacturer's recommended minimum conductor bend radius. 1. Size, Unless Otherwise Indicated: 4 inches square by 2-1/8 inches deep. 2. Wall-Mounted Telephones: 4 inches high by 2 inches wide by 2-1/8 inches deep. 3. Wall Plates: High impact thermoplastic, color to be selected, complying with system design standards and UL 514C.
PART 3 EXECUTION 3.01 INSTALLATION - GENERAL A.
Comply with latest editions and addenda of TIA/EIA-568, TIA/EIA-569, ANSI/J-STD-607, and SYSTEM DESIGN as specified in PART 2.
3.02 PATHWAYS A.
Install with minimum clearances per Section 26 05 34.
B.
Conduit: 1. Do not install more than three (3) 90 degree bends in a single horizontal cable run. 2. Leave pull cords in place where cables are not initially installed. 3. Conceal conduit within finished walls, ceilings, and floors except where concealment is not possible. a. Conduit may remain exposed to view in mechanical rooms, electrical rooms, and telecommunications rooms. b. Where exposed to view, install parallel with or at right angles to ceilings, walls, and structural members. Architect must approve exposed raceway prior to installation.
C.
Outlet Boxes: 1. Coordinate locations of outlet boxes provided under Section 26 05 37 as required for installation of access control, video surveillance, and duress device locations provided under this section. a. Orient outlet boxes for vertical installation of wiring devices unless otherwise indicated. b. Provide minimum of 24 inches horizontal separation between flush mounted outlet boxes installed on opposite sides of fire rated walls. c. Unless otherwise indicated, provide separate outlet boxes for line voltage and low voltage devices. d. Locate outlet boxes so that wall plate does not span different building finishes. e. Locate outlet boxes so that wall plate does not cross masonry joints.
D.
Grounding and Bonding: Perform in accordance with NEC and ANSI/J-STD-607.
E.
Firestopping: Seal openings around pathway penetrations through fire-rated walls, partitions, floors, and ceilings in accordance with Section 07 84 00. END OF SECTION 27 10 05
DAS Courts Sec Systems Reg 1 / HE-3206.6 27 10 05 - 2
LOW-VOLTAGE CABLING PATHWAYS
SECTION 28 13 00 ACCESS CONTROL PART 1 GENERAL 1.01 SECTION INCLUDES A.
Access control devices.
B.
Access control panel.
C.
Access control software.
1.02 RELATED REQUIREMENTS A.
Section 08 71 00 - Door Hardware.
B.
Section 26 05 19 - Low-Voltage Electrical Power Conductors and Cables (600 V and Less).
1.03 SCOPE OF WORK A.
All controllers, control boards, housings, backup batteries, power supplies, mounts, wiring, servers, pc's, monitors, software programing and any other required hardware to be provided by Contractor.
B.
120 volt power sources to be provided by Contractor.
1.04 REFERENCES A.
NFPA 70 - National Electrical Code; National Fire Protection Association; Most Recent Edition Adopted by Authority Having Jurisdiction, Including All Applicable Amendments and Supplements.
1.05 SUBMITTALS A.
See State of Oregon General Conditions for Public Improvements Contracts for submittal procedures.
B.
Shop Drawings: Provide system wiring diagram showing each device and wiring connection required. Provide sequence of operation for each access door. See Section 26 05 05.
C.
Product Data: Provide electrical characteristics and connection requirements.
D.
Test Reports: Indicate satisfactory completion of required tests and inspections.
E.
Manufacturer's Installation Instructions: Indicate application conditions and limitations of use stipulated by product testing agency. Include instructions for storage, handling, protection, examination, preparation, installation, and starting of product.
F.
Project Record Documents: Record actual locations of access authorization equipment. See Section 26 05 05.
G.
Operation Data: Operating instructions.
H.
Maintenance Data: Maintenance and repair procedures.
I.
Maintenance Materials: Furnish the following for Owner's use in maintenance of project. 1. See State of Oregon General Conditions for Public Improvements Contracts for additional provisions. 2. Deliver keys/cards not used in initial installation to Owner as directed.
1.06 QUALITY ASSURANCE A.
Conform to requirements of NFPA 70.
B.
Manufacturer Qualifications: Company specializing in manufacturing the products specified in this section.
C.
Installer Qualifications: Company specializing in installing the products specified in this section with minimum three years documented experience.
D.
Products: Furnish products listed and classified by Underwriters Laboratories Inc. or testing firm acceptable to authority having jurisdiction as suitable for purpose specified and indicated.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 1
ACCESS CONTROL
PART 2 PRODUCTS 2.01 MANUFACTURERS A.
Access Control System Software, Controllers, and Input Devices: 1. Honeywell; www.security.honeywell.com. 2. Substitutions: See State of Oregon General Conditions for Public Improvements Contracts.
2.02 ACCESS CONTROL SOFTWARE A.
The access control software shall be the human interface with the control and configuration for all access points, monitor input points, and relay controlled outputs as indicated on the drawings and further described in this technical specification.
B.
The access control software shall interface and operate fully with database distributed control processors. Control processor specifications are further described in the technical specification herein.
C.
The basic access control system software shall meet the following minimum, design and performance specifications as a fully integrated Alarm and Access Control Management System: 1. Software shall be designed to provide an intuitive and self identifying flow of operation, providing a more User friendly interface between an operator and the software during daily activity processing and training. 2. Software shall be designed as a single platform allowing the User to establish a single server application and when it is desired upgrade to an enterprise (multi-server) application to manage and control multiple properties using multiple servers with few if any changes to the User's installation. 3. Software shall support optional multiple third party product NVR/DVR integration modules. These modules shall be fully integrated into the system allowing the User to define views and camera selections based on the third party product functionality. 4. Software shall provide and utilize “wizard” style interactive guidance to allow the system administrators or operators to perform standard configuration tasks in a step-by-step training process. 5. User Groups defined specific privileges to access, view or modify software application functions for the User. Passwords for Users may be linked with the User's active directory for internal management if desired. 6. Software shall support unlimited User-defined Macros to allow HOST generated system activities and events to trigger pre-configured actions system wide. 7. HOST generated Macros shall incorporate processor level Tasks and Tasks shall incorporate Macros providing a fluid interactive processing of system and field level commands. Tasks shall be stored in each system processor as part of the distributed database allowing total self supported and local control at the processor level as defined by the User. 8. Software shall support a Macro base scheduler allowing the User to schedule system wide actions based on separately scheduled periods rather than on pre-determined time zones. 9. Software shall support a non-proprietary Serial Enabled Auto-Dialer Solution that allows a User to define any input within the system as an alarm for local response and pre-defined reporting or to a remote central station for reporting and response or both within the same system. 10. Software shall support all of the setup files and processing to allow central station reporting as a User defined operation without the need for additional software modules or software options. 11. Software shall be capable of both remote burg panel integration with access input I/O interface and serial enabled auto-dial solution remote reporting of all access inputs and events without I/O interface. 12. Software shall identify any change to an inputs status as an alarm or event as defined by the User and managed with automated or manual actions.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 2
ACCESS CONTROL
13. Software monitoring and control of all alarm and status points shall be managed and reported as defined by the User through a real-time display or displays in the Users proprietary monitoring location(s) or in remote central station(s) also defined by the User. 14. Software shall support the control of elevator floor selection, where required through the associated field hardware without special processors or separate hardware panels. 15. Software shall support output control relays with automated control configuration processing to control external devices and interface with other systems as required. 16. Software shall archive all events, alarms, control activations and restorals in a system archive file and retain all current events until an archive is performed. 17. Software shall support alarm and event filtering to allow User-defined exceptions to normal alarm and event displays to system operators. 18. Software shall support routing of individual alarm events to specific workstations. Alarm routing instructions may be associated with time zones in order to allow automatic changes in alarm destinations based on time of day. 19. Software shall provide and support an automatic backup utility. This utility shall allow for automatic, scheduled backups of both database and archive files. 20. Software shall provide multiple, pre-configured database and transaction history report formats. These reports shall utilize reusable report selection criteria and structured for presentation to the User in a Wizard format. 21. Software shall support precision access to allow each cardholder to be provided access privileges to specific doors in addition to any doors included in their assigned access levels. 22. Software shall allow the User to assign holiday groups within time zone definitions and time zones to specific access levels providing control for all site wide card holder authorizations and access, input and output points. 23. Software shall support User selection of communications media and protocol. The minimum communication methods are RS-232, RS-485, Dialup (industry standard dial modem) and network standard TCP/IP or PoE. Alternate (backup) communications shall be supported as required. 24. Software shall allow system operators to monitor operator-selected doors in order to perform cardholder verification. With each card transaction, the stored image associated with that card shall be displayed on the selecting operator workstation. 25. Software shall allow search and display operations on all data fields providing the User a friendly report management and display capability without requiring the use of third party report writer software. 26. Software shall report changes in status for all I/O points in real-time on any operator display terminal for view and response. The real-time operator display shall allow the operator to select a video view of pre-assigned locations. 27. Software shall allow an operator to manage output control relays at selected areas, as shown on the drawings, to control external devices and interface with other systems manually or through define control point automation by time, event, field processing Tasks, and/or within HOST Macros. The real-time operator display shall allow the operator to select a video view of pre-assigned locations. 28. Software shall provide a utility to create and assign card groups. Card groups shall allow the User to pre-assign automation (macro or task) to a card group and apply the automation to a card holder's activity at all or specific readers and/or keypads. Card group shall be assignable to a specific cardholder or group to perform commands. Card groups shall be area or system wide and used for such functions as manually set lockdowns, area opens and closes, or first access, etc. 29. Software shall support a hierarchical device tree with active status icons. The device tree shall show the pre-programmed forms per device and a complete listing of all control processors, sub-controller modules and the individual devices, readers, inputs, outputs and optional third party products installed and active in the system. 30. Software shall support interactive graphical maps displayed on selected system workstations to indicate the location of alarms and system field devices on site specific maps. The graphics window shall be un-dock able.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 3
ACCESS CONTROL
31. Software shall allow the User to assign graphics or icons to specific points and field devices to allow interactive controls from a map display by authorized system operators. 32. Software shall support multi-state map icons to indicate alarm or pending alarm states to the workstation operator such as door open or door closed, etc. 33. Software shall provide interactive controls specific to each icon using Microsoft key functionality for select, display and command. An operator shall have the ability to view the status of a point (icon) displayed on a User defined map by placing the system cursor over the icon (alarm). This display shall detail all points associated with the status of the specific icon type; such as an access reader showing the door contact, the egress point and the lock control. 34. Alarm zones shall be displayed on graphical maps to provide, at a glance, area armed and disarmed status. Alarm zone arming and disarming shall be an interactive graphical map function. 35. Software shall support event filtering to allow User-defined exceptions to be displayed to pre-defined system operators by event type or event location. 36. Software shall be able to receive device status changes and display such changes in 1 to 3 seconds of the change. 37. Software shall manage high level system services on the HOST server allowing the server client to be shut down or minimized without effecting normal system operation of any of the field devices. 38. Software shall maintain a system level status display screen showing the operating status of all accumulated events and general system activity for the system operator's review on a single screen. 39. Software communication between the HOST and the control processors shall be a high level interrogation-response protocol allowing the HOST to identify the status of all control processors, all sub-controller modules and the associated field devices managed and controlled by these modules. Systems that do not support a real-time interrogation-response protocol shall be considered non-complaint and unacceptable. 40. Software shall support Dial-up protocol between the HOST and a control processor. The interconnection shall use industry standard modems allowing the field control processor to report to the HOST at specific intervals, at any time when the HOST connects to the control processor or the control processor is reporting an event or alarm. 41. Software configurations downloaded to the control processor are locally stored in a distributed processing manner allowing the processor to determine access request validly and grant or deny access to a cardholder, at a sub-controller in less than 1 second without HOST intervention. 2.03 COMPUTER HARDWARE A.
All computer hardware components required to support the access, alarm and device control system, described within this specification, will be provided by the specified system vendor.
B.
Server(s) - any computer described as a server, and as indicated on the drawings, will meet the following, minimum design and performance specifications. 1. Processor: Core i7 Processor, or greater. 2. Operating system: Windows 2012 Server or higher 3. Database management system: SQL Server 2008 Express Edition or SQL Server 2008 or higher. 4. Memory: 4GB of RAM, or larger 5. DVD/DVD-RW/CD-RW drive 6. 750GB Hard disk drive 7. At least one serial port, at least two USB 2.0 ports, and one parallel port 8. Keyboard and mouse 9. Display monitor (LCD), minimum 21 inch display size
C.
Workstation(s) - any computer described as a workstation, and as indicated on the drawings, will meet the following, minimum, design and performance specifications: 1. Processor: Core i7 Processor, or greater.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 4
ACCESS CONTROL
2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Operating system: Windows 7 Business or higher. SQL Server 2008 Client Access License (CAL) or higher. Microsoft Office 2007, 2010, or 2013 with MS Word and MS Excel Memory: 4GB of RAM, or larger DVD/DVD-RW/CD-RW drive 200GB Hard disk drive At least one serial port, at least two USB 2.0 ports, and one parallel port Keyboard and mouse Display monitor (LCD), minimum 21 inch display size The system provider will be responsible for ensuring that each computer hardware component also includes any and all interfaces, expansion boards, and peripherals that will be necessary to allow the system to operate as described within this specification.
2.04 SYSTEM CONTROL PROCESSOR (SCP) A.
Where required by design and indicated on the drawings, an EP system control processor (SCP) shall be a 32-bit micro-controller utilized as the enhanced management processor between additional down line access reader, input monitor and relay output modules and the HOST system and software as specified herein.
B.
The SCP shall meet the following, minimum, design and performance specifications. 1. SCP internal memory shall be a minimum of 32 Mbytes with a minimum of 12 Mbytes of memory set aside for User configuration. 2. SCP shall provide support for up to thirty-two (32) I/O module addresses, as required by design and indicated on the drawings. 3. SCP shall provide capacity for up to, and in any combination, minimum of 16 readers, 512 input monitoring points, and 512 relay output points; as required by design and indicated on the drawings. 4. SCP shall provide User selection of serial, dial-up and/or Ethernet (TCP/IP) communications to the host computer with the specified system software. No external network card or attachment device shall be required for the SCP to connect with a conventional Ethernet. The User shall have the ability to connect with the SCP using static IP or DHCP conventions supported in the EP SCP. 5. The SCP on board Network Interface Circuit (NIC) shall support 10/100-BaseT automation. 6. SCP shall maintain a distributed database independent from the host computer so that local processing, within the SCP and I/O modules, shall not rely on the host computer to process card access attempts or defined site control events. Site control events shall be special User configured process tasks and shall occur as defined with or without HOST connectivity. 7. SCP shall internally support up to 32 access levels per card holder, holidays and group holidays, precision access, and multiple time zone assignments. 8. Each SCP in the access system shall support a minimum of eight (8) active card formats per processor. 9. SCP shall report the entire card number reported on invalid reads 10. SCP shall support 19 digit (64-bit) UserId and up to 15 digit PIN numbers per card record. 11. SCP shall internally support anti-passback functions including free pass, exempt flags, last area accessed, last reader accessed and time and date of last access. 12. SCP shall internally support area management functions including two man rules, two card rules, multiple occupancy, maximum occupancy, and nested areas. Area management functions shall be defined in a minimum of up to 32 Access Area assignments per SCP. Access Areas shall be treated within the system as a single logical point and any controls applied manually or by automation will apply to all of the access points assigned within the Access Area. Access Area processing shall be fully distributed allowing operations assigned to tasks to be processed with or without HOST connectivity. 13. SCP shall internally support alarm management functions incorporating inputs and reader events into Alarm Zones allowing the zones to be armed and disarmed creating various
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 5
ACCESS CONTROL
14.
15.
16.
17.
18.
19. 20. 21. 22. 23.
User definable events that are supported in SCP tasks and HOST macro processing. The SCP shall support a minimum of 64 fully User configurable Alarm Zones per processor. Alarm Zone processing shall be fully distributed allowing operations assigned to tasks to be processed with or without HOST connectivity. SCP alarm management shall provide task as well as arm / disarm functionality using a standard keypad/display terminal/card reader with features for User command and key selection. The SCP shall support down loads to the display of the keypad for date and time, zone status, error messages and special text messaging defined by the User. An SCP shall provide direct reporting of all events and status to the HOST system as well as communication support to an optional third party remote reporting product for unattended hour's operation. SCP remote event and status reporting shall use standard POTS telephone lines to communicate with an independent central station provider using security industry standard SIA protocol to communicate User pre defined site alarm and access events. The User shall have full management and control of all access/PIN functionality as well as full management and control of all transmitted event and status information passed to the central station. This reporting module shall be installed in the same enclosure as the SCP and linked directly to an RS-232 communication port on the EP. SCP shall internally support up to two hundred fifty six (256) User definable tasks configured to execute pre-defined process operations in response to manual User commands, input or event changes, time zone activations, automated commands or Macro operations. SCP shall internally support up to two hundred fifty six (256) User definable User commands configured to execute pre-defined process commands in response to manual User commands, input or event changes, time zone activations, automated commands or Macro operations. The SCP shall support a serial data output function that allows the User to link to any event or status change received by the SCP with an ACSII data file communicated through an assigned serial data port to other control equipment. ACSII messages shall be standard format and allow up to 90 characters to be send per message not including required CR or CRLF requirements. Port assignment, data channel and data append information shall be User defined. The data port provided on the SCP shall be IEEE standard RS-485 connectivity. SCP shall allow variable transaction storage from 1,000 to 100,000 events per SCP. The SCP shall allow variable local card database storage from 5,000 to 350,000 records per SCP. The SCP operational programming shall be stored in non-volatile Flash Memory allowing for on-line program upgrades. SCP shall provide on board memory battery backup to retain all database information during a complete power loss for up to sixty (60) days, per manufacturer's specifications. SCP shall provide (2) two-wire RS-485 down line communication ports for conventional SIO communication and a DHCP server type communication protocol for network connected IP based SIO devices for access, alarm and control operations. The minimum data rate shall be 38,400KBps. Up to 32 SIO devices shall be connected on any RS-485 down-line loop at up to 4,000' and/or through a network switching and IP standard connectivity.
C.
The SCP shall meet or exceed the following standards or compatibility requirements. 1. SCP shall be UL294 recognized and CE compliant. 2. SCP shall be FCC Part 15 Class A 3. SCP shall utilized AES 128-bit NIST certified encryption. 4. SCP shall be PIV-II, CAC, & TWIC card compatible. 5. SCP shall be HSPD-12/FIPS201 compliant.
D.
Each SCP shall be installed either in a dedicated enclosure or share an enclosure with other associated access, input or output system modules and/or an afterhours reporting module for central station reporting.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 6
ACCESS CONTROL
1. 2. 3.
E.
SCP shall have a dedicated cabinet tamper monitor input. SCP shall have a dedicated power fail monitor input. When sharing an enclosure with other associated access reader, input monitor and relay output modules, only one of the modules will be required to monitor cabinet tamper and power fail inputs.
The SCP shall meet the following physical specifications, excluding the required enclosure: 1. Input voltage: 12-24 Vdc, +/- 10%, 300mA 2. Primary HOST Port: 10/100 Ethernet 3. Secondary HOST Port 1: Serial RS-232, 2-wire RS-485, Modem or Ethernet adaptor. 4. Down line Port 2: 2-Wire RS-485 5. Down-line Port 3: 2-wire RS-485 6. Inputs: Two dedicated unsupervised tamper and power monitor 7. Temperature requirements: 0 degrees F to 70 degrees F, operating 8. Relative humidity: 0 percent to 95 percent, non-condensing
2.05 SYSTEM CONTROL PROCESSOR (SCP) DUAL READER INTERFACE A.
Where required by design and indicated on the drawings, the system control processor (SCP) Dual Reader Interface shall be a 32-bit micro-controller utilized as the enhanced management processor between additional down line access reader, input monitor and relay output modules and the HOST system and software as specified herein.
B.
The SCP Dual Reader Interface shall support up to two (2) security industry standard reader communication and control ports. Each port shall terminate with industry standard access control readers and/or data entry/display terminals (keypad with display) for authorized access and egress management. Each SCP access port shall have supervised portal monitoring (door status), request to exit monitoring (manual or automated inputs) as well as electrified lock output control. Each reader port shall support TTL, Wiegand, RS-485 and OSDP protocol.
C.
The SCP shall meet the following, minimum, design and performance specifications. 1. SCP internal memory shall be a minimum of 16 Mbytes with a minimum of 6 Mbytes of memory set aside for User configuration. 2. SCP shall provide support for up to thirty-two (32) I/O module addresses, as required by design and indicated on the drawings. 3. SCP shall provide capacity for up to, and in any combination, 64 reader locations including status / position monitoring, egress request automation and electric lock control, 512 monitoring points, and 512 relay output points; as required by design and indicated on the drawings. 4. SCP shall provide User selection of serial, dial-up and/or Ethernet (TCP/IP) communications to the host computer with the specified system software. No external network card or attachment device shall be required for the SCP to connect to the HOST system on a conventional Ethernet. The User shall have the ability to connect with the SCP using static IP or DHCP conventions. 5. The SCP on board Network Interface Circuit (NIC) shall support 10/100-BaseT automation. 6. SCP shall maintain a distributed database independent from the host computer so that local processing, within the SCP and I/O modules, shall not rely on the host computer to process card access attempts or defined site control events. Site control events shall be special User configured process tasks and shall occur as defined with or without HOST connectivity. 7. SCP shall internally support multiple access levels per card holder, holidays and group holidays, precision access, and multiple time zone assignments. 8. Each SCP in the access system shall support a minimum of eight (8) active card formats per processor. 9. SCP shall internally support anti-passback functions including free pass, exempt flags, last area accessed, last reader accessed and time and date of last access. 10. SCP shall internally support area management functions including two man rules, two card rules, multiple occupancy, maximum occupancy, and nested areas. Area management
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 7
ACCESS CONTROL
11.
12.
13.
14.
15.
16.
17.
18. 19. 20. 21. 22.
functions shall be defined in a minimum of 32 Access Area assignments per SCP. Access Areas shall be treated within the system as a single logical point and any controls applied manually or by automation will apply to all of the access points assigned within the Access Area. Access Area processing shall be fully distributed allowing operations assigned to tasks to be processed with or without HOST connectivity. SCP shall internally support alarm management functions incorporating inputs and reader events into Alarm Zones allowing the zones to be armed and disarmed creating various User definable events that are supported in SCP tasks and HOST macro processing. The SCP shall support a minimum of 64 fully User configurable Alarm Zones per processor. Alarm Zone processing shall be fully distributed allowing operations assigned to tasks to be processed with or without HOST connectivity. SCP alarm management shall provide task as well as arm / disarm functionality using a standard keypad/display terminal/card reader with features for User command and key selection. The SCP shall support down loads to the display of the keypad for date and time, zone status, error messages and special text messaging defined by the User. An SCP with shall provide direct reporting of all events and status to the HOST system as well as communication support to an optional third party remote reporting product for unattended hour's operation. SCP remote event and status reporting shall use standard POTS telephone lines to communicate with an independent central station provider using security industry standard SIA protocol to communicate User pre defined site alarm and access events. The User shall have full management and control of all access/PIN functionality as well as full management and control of all transmitted event and status information passed to the central station. This reporting module shall be installed in the same enclosure as the SCP and linked directly to an RS-232 communication port on the EP. SCP shall internally support alarm management functions incorporating inputs and reader events into Alarm Zones allowing the zones to be armed and disarmed creating various User definable events that are supported in SCP tasks and HOST macro processing. The SCP shall support a minimum of 64 fully User configurable Alarm Zones per processor. Alarm Zone processing shall be fully distributed allowing operations assigned to tasks to be processed with or without HOST connectivity. SCP alarm management shall provide task as well as arm / disarm functionality using a standard keypad/display terminal/card reader with features for User command and key selection. The SCP shall support down loads to the display of the keypad for date and time, zone status, error messages and special text messaging defined by the User. SCP shall internally support up to two hundred fifty six (256) User definable tasks configured to execute pre-defined process commands in response to manual User commands, input or event changes, time zone activations, automated commands or Macro operations. SCP shall internally support up to two hundred fifty six (256) User definable User commands configured to execute pre-defined process commands in response to manual User commands, input or event changes, time zone activations, automated commands or Macro operations. SCP shall allow variable stored transaction storage from 1,000 to 100,000 events per SCP. The SCP shall allow variable local card database storage from a minimum of 5,000 to 250,000 records per SCP. The SCP operational programming shall be stored in non-volatile Flash Memory allowing for on-line program upgrades. SCP shall provide on board memory battery backup to retain all database information during a complete power loss for up to sixty (60) days, per manufacturer's specifications. SCP shall provide (1) two-wire RS-485 down line communication ports for conventional SIO communication and a DHCP server type communication protocol for network connected IP based SIO devices for access, alarm and control operations. The minimum data rate shall be 38,400KBps. Up to 32 SIO devices shall be connected on any RS-485 down-line loop at up to 4,000' and/or through a network switching and IP standard connectivity.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 8
ACCESS CONTROL
D.
The SCP Dual Reader Interface shall support the following: 1. SCP shall support up to two (2) security industry standard readers' (Wiegand, Mag-swipe or RS-485. This shall also support OSDP protocol for RS-485 readers and/or data entry/display terminals (keypad with display) for access or egress authorizations. 2. SCP reader ports shall provide up to 150 mA of unregulated 12 Vdc power for each reader. At a minimum card/data input support shall be Wiegand, TTL or RS-485 and OSDP formats. Single and dual wire LED output shall be provided supporting bicolor display. Reader buzzer support shall also be provided. 3. SCP shall provide eight (8) on board fully supervised monitoring points (inputs). These monitoring points shall be configured as follows: (2) Monitoring points shall be dedicated for access portal status (door contact inputs) one per reader port. (2) Monitoring points shall be dedicated for exit request inputs (manual or automated egress) one per reader port. (4) Monitoring points shall be auxiliary and fully User defined for monitoring other devices or points within the site as required by design and indicated on the drawings. 4. SCP input monitoring point settings shall be User defined as normally open, normally closed or supervised normally open or normally closed. At a minimum input supervision shall be a series parallel 1/4W, 1%, 1K by 1K Ohm resistor circuit. 5. The SCP shall provide four (4) on board output relays for controlling electrified devices or switching inputs. These relays shall be configured as follows: (2) Relays shall be dedicated for electric portal locking device control one per reader port. (2) Relays shall be auxiliary and fully User defined for controlling or switching other devices or points within the site as required by design and indicated on the drawings. 6. All SCP output relays shall be Form-C, 5A@30 Vdc, resistive relays. 7. All SCP output relays shall allow configuration for fail safe or fail secure operation and shall support ON, OFF, and PULSE, command states.
E.
The SCP shall meet or exceed the following standards or compatibility requirements. 1. SCP shall be UL294 recognized and CE compliant. 2. SCP shall utilized AES 128-bit NIST certified encryption. 3. SCP shall be PIV-II, CAC, & TWIC card compatible. 4. SCP shall be HSPD-12/FIPS201 compliant.
F.
Each SCP shall be installed either in a dedicated enclosure or share an enclosure with other associated access, input or output system modules. 1. SCP shall have a dedicated cabinet tamper monitor input. 2. SCP shall have a dedicated power fail monitor input. 3. When sharing an enclosure with other associated access reader, input monitor and relay output modules, only one of the modules will be required to monitor cabinet tamper and power fail inputs.
G.
The SCP shall meet the following physical specifications, excluding the required enclosure. 1. Input voltage: 12-24 Vdc, +/- 10%, 500mA 2. Primary Port: 10/100 Ethernet 3. Secondary Port 1: Serial RS-232, 2-wire RS-485, Modem or Ethernet adaptor. 4. Down line Port 2: 2-Wire RS-485 5. Reader Ports: 2, TTL, Wiegand & RS-485, bi-color LED/Buzzer Cntl. 6. Inputs:8 fully supervised 7. Output Relays: 4, Form-C 5 Amp 30 VDC 8. Inputs: Two dedicated unsupervised tamper and power monitor 9. Temperature requirements: 0 degrees F to 70 degrees F, operating 10. Relative humidity: 0 percent to 95 percent, non-condensing
2.06 SINGLE PORTAL (PAIRED READER) IP ADDRESSABLE SYSTEM CONTROL PROCESSOR (SCP) A.
The Single Portal IP Addressable SCP shall provide distributed processing and management for Single Portal IP/PoE sub-controller Modules and conventional serial sub-controller modules. Up to 8 Single Portal IP/PoE modules can be connected to a Single Portal IP/PoE SCP.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 9
ACCESS CONTROL
B.
The Single Portal IP/PoE SCP shall meet the following, minimum, design and performance specifications. 1. Single portal IP/PoE SCP shall support security industry standard TTL, Wiegand, RS-485 and OSDP protocol, primary port only, for all reader ports. 2. Single portal IP/PoE SCP shall support two (2) reader ports used on a single portal as and access and egress for the assigned portal. 3. Single portal IP/PoE SCP shall support keypads and integrated keypad readers. 4. Single portal IP/PoE SCP shall support connectivity and interface with a system arm / disarm functionality using a standard OSDP protocol keypad/display terminal/card reader with features for User command and key selection. 5. The Single portal IP/PoE SCP shall support all database configurations for down loads Single portal IP/PoE modules as well as conventional serial sub-controller modules connected to the SCP from an on-board TTL (RS-485 protocol) down line. Maximum serial port distance 1,000 feet from the SCP to the last sub-controller. 6. Network connection to the Single portal IP/PoE SCP shall be via a powered network switch or conventional network switch. The maximum power available from a powered network switch is 650ma, maximum. 7. All hardware operation and data settings shall be loaded through software commands at the HOST system software and down loaded to sub-controller modules using network and serial (RS-485) communication protocols. 8. The Single portal IP/PoE SCP shall provide two (2) on board supervised monitoring points (inputs). These monitoring points shall be configured as follows: (1) Input dedicated for access portal status (contact inputs). (1) Input dedicated for exit request inputs (manual or automated egress). 9. Single portal IP/PoE SCP input monitoring point settings shall be User defined as normally open normally closed or supervised normally open or normally closed for the pre-defined portal. At a minimum input supervision shall be a series parallel 1/4W, 1%, 1K by 1K Ohm resistor circuit. 10. The Single portal IP/PoE SCP shall provide two (2) on board output relays for controlling electrified devices or switching inputs. These relays shall be configured as follows: (1) Relay dedicated to the electric portal locking device. (1) Relay auxiliary and fully User defined for other relay control devices. 11. Single portal IP/POE SCP output relays shall allow configuration for fail safe or fail secure operation and shall support ON, OFF, and PULSE, command states. 12. In the event of a communication failure with the HOST system, the Single portal IP/POE SCP shall be fully capable of verification and event processing as configured from its on-board configuration memory (distributed processing). 13. The Single portal IP/POE SCP operational programming shall be stored in non-volatile Flash Memory allowing for on-line program upgrades. 14. The Single portal IP/POE SCP supports AES 128-bit NIST Certified Encryption to the HOST providing secure data communications. 15. Single portal IP/POE SCP shall utilize IEEE standard CAT5 or CAT6 communication cable connection with data rates up to 38,400KBps up to an IEEE standard of 100 meters (approximately 300 feet), standard IP network cabling from installed switch locations.
C.
Each Single portal IP/POE SCP shall be installed in an 8" x 8" x 4" NEMA 1 enclosure. The module may also be installed in a conventional enclosure with other associated access, input and output control modules and local battery backed up 12 Vdc module power. 1. Single portal IP/POE SCP shall be connected to the HOST system through a network switch, POE or conventional and only at a single network switch level. 2. Single portal IP/POE SCP shall have a dedicated power monitor input. 3. Connectivity: Primary Port: 10/100 Ethernet 4. Door Control: One physical barrier can be controlled using single or paired readers. 5. Access Control:
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 10
ACCESS CONTROL
a. 6.
7.
D.
240,000 Cardholder capacity, 50,000 Transaction buffer, 32 Access Levels per cardholder, 19 digit (64-bit) User ID and 15 digit PIN numbers maximum, Activation and Deactivation dates, If/Then Macro capability Card Formats: a. Eight active card formats per intelligent controller b. 19 digit (64-bit) User ID and 15 digit PIN numbers maximum c. PIV-II, CAC, TWIC card compatible NOTE: When sharing an enclosure with other associated access control system modules, only one of the modules in the enclosure shall be required to monitor cabinet tamper and power fail inputs.
The Single portal IP/POE SCP shall meet the following physical specifications, excluding the required enclosure. 1. Input voltage: 12VDC ±10% 900 mA maximum power supply, 200 mA minimum power. Power over Ethernet (PoE) power input 12.95 watts, compliant to IEEE 802.3af 2. Power Output:12 Volts DC at 650mA including reader and AUX output. 3. Primary Port: RJ45 conventional Network connection 4. Reader Ports:2, TTL, Wiegand or RS-485, bi-color LED and Buzzer support, keypad multiplexed with card data and OSDP protocol. 5. Reader Power:via PoE, 12VDC ±10% regulated or local power supply (12VDC). PTC limited to 150mA maximum 6. Reader Ports:2, one transistor-transistor logic (TTL) reader port and one TTL or 2-wire RS-485 reader port. PLUS 1,000 foot down line for remote sub-controller communication. 7. Keypad:Multiplexed with card data 8. LED:TTL, 2 wire or 1 wire bi-color support 9. Buzzer:One-wire LED mode 10. Inputs: 2 fully supervised (2 Portal Contact and Request to Exit. 11. Un-supervised 1 Cabinet Tamper 12. Outputs: 2 General Purpose Relays, 1 lock power, 1 AUX 13. Lock Relay:1 Lock Control - Form-C, 2 Amp 30 VDC 14. Auxiliary Relay: Form-C, 2 Amp 30 VDC 15. Temperature: 0 to 77 degrees Centigrade operational, -55 to 85 degrees Centigrade storage 16. Relative humidity: 10 to 95 percent, non-condensing (RHNC)
2.07 SINGLE PORTAL (PAIRED READER) IP ADDRESSABLE MODULE (SUB-CONTROLLER) A.
The System Control Processor (SCP) shall provide distributed processing and management for each Single Portal IP/PoE Module incorporated in the system. Up to 32 Single Portal IP/PoE modules can be connected to an SCP.
B.
The single portal IP/PoE module shall meet the following, minimum, design and performance specifications. 1. Single portal IP/PoE module shall support security industry standard TTL, Wiegand, RS-485 and OSDP protocol, primary port only, for all reader ports. 2. Single portal IP/PoE module shall support two (2) reader ports used on a single portal as and access and egress for the assigned portal. 3. Single portal IP/PoE module shall support keypads and integrated keypad readers. 4. Single portal IP/PoE module shall support connectivity and interface with a system arm / disarm functionality using a standard OSDP protocol keypad/display terminal/card reader with features for User command and key selection. 5. The Single portal IP/PoE module shall support down loads from the SCP to the display of the keypad for date and time, zone status, error messages and User defined special text messaging through a DHCP like network link with the EP SCP. 6. Network connection to the Single portal IP/PoE module shall be via a powered network switch or conventional network switch. The maximum power available from a powered network switch is 700ma, maximum.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 11
ACCESS CONTROL
7. 8.
9.
10.
11. 12. 13. 14. 15.
All hardware interface and card format settings shall be loaded through software commands from the specified system software to associated SCP modules to each Single portal IP/PoE module. The Single portal IP/PoE module shall provide four (4) on board fully supervised monitoring points (inputs). Two of these monitoring points shall be configured as follows: (1) Monitoring point dedicated for access portal status (contact inputs). (1) Monitoring point dedicated for exit request inputs (manual or automated egress). The remaining two (2) are AUX inputs to be assigned by the User for any event or alarm point. Single portal IP/PoE module input monitoring point settings shall be User defined as normally open, normally closed or supervised normally open or normally closed. At a minimum input supervision shall be a series parallel 1/4W, 1%, 1K by 1K Ohm resistor circuit. The Single portal IP/PoE module shall provide two (2) on board output relays for controlling electrified devices or switching inputs. These relays shall be configured as follows: (1) Relay dedicated to the electric portal locking device. (1) Relay auxiliary and fully User defined for other relay control devices. Single portal IP/POE module output relays shall allow configuration for fail safe or fail secure operation and shall support ON, OFF, and PULSE, command states. In the event of a communication failure with the EP System Control Processor (SCP), the Single portal IP/POE module shall be capable of locally processing access requests based on up to 8 facility codes at the portal for verification. The Single portal IP/POE modules operational programming shall be stored in non-volatile Flash Memory allowing for on-line program upgrades. The Single portal IP/POE module allows AES 128-bit NIST Certified Encryption to the EP SCP providing a secure reader termination. Single portal IP/POE module shall utilize IEEE standard CAT5 or CAT6 communication cable connection with data rates up to 38,400KBps up to an IEEE standard of approximately 300 feet, standard IP network cabling from installed switch locations.
C.
Each Single portal IP/POE module shall be installed in an 8" x 8" x 4" NEMA 1 enclosure. The module may also be installed in a conventional enclosure with other associated access, input and output control modules and local battery backed up 12 Vdc module power. 1. Single portal IP/POE module shall be connected to the system control processor through a network switch, POE or conventional and only at a single network switch level. 2. Single portal IP/POE module shall have a dedicated power monitor input. 3. Connectivity: Primary Port: 10/100 Ethernet 4. Door Control: One physical barrier can be controlled using single or paired readers. 5. Access Control: a. SCP on line - 19 digit (64-bit) User ID and 15 digit PIN numbers maximum b. SCP User configured - Locked, Unlocked or Facility Code 6. Card Formats: a. Eight active card formats per intelligent controller b. 19 digit (64-bit) User ID and 15 digit PIN numbers maximum c. PIV-II, CAC, TWIC card compatible 7. NOTE: When sharing an enclosure with other associated access control system modules, only one of the modules in the enclosure shall be required to monitor cabinet tamper and power fail inputs.
D.
The Single portal IP/POE module shall meet the following physical specifications, excluding the required enclosure. 1. Input voltage: 12VDC ±10% 900 mA maximum power supply, 200 mA minimum power. Power over Ethernet (PoE) power input 12.95 watts, compliant to IEEE 802.3af 2. Power Output:12 Volts DC at 700mA including reader and AUX output. 3. Primary Port: RJ45 conventional Network connection, Ethernet, 10BaseT/100BaseTX, AES 128 bit encrypted 4. Reader Ports:2, TTL, Wiegand or RS-485, bi-color LED and Buzzer support, keypad multiplexed with card data and OSDP protocol.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 12
ACCESS CONTROL
5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
Reader Power:via PoE, 12VDC ±10% regulated or local power supply (12VDC). PTC limited to 150mA maximum Keypad:Multiplexed with card data LED:TTL, 2 wire or 1 wire bi-color support Buzzer:One-wire LED mode Inputs: 4 fully supervised (2 Portal Contact and Request to Exit, 2 (AUX). Un-supervised 1 Cabinet Tamper Outputs: 2 General Purpose Relays, 1 lock power, 1 (AUX) Lock Relay:1 Lock Control - Form-C, 5 Amp 28 VDC Auxiliary Relay: 1 Form-C, 5 Amp 28 VDC Temperature: 0 to 77 degrees Centigrade operational, -55 to 85 degrees Centigrade storage Relative humidity: 10 to 95 percent, non-condensing (RHNC)
2.08 ACCESS CONTROL SINGLE READER I/O MODULE (RS-485 NETWORK) A.
The System Control Processor (SCP) shall provide distributed processing and management for each Single Reader I/O Module incorporated in the system.
B.
The single reader I/O module shall meet the following, minimum, design and performance specifications. 1. Single Reader I/O Module shall support security industry standard TTL, Wiegand, RS-485 and OSDP protocol. 2. Single Reader I/O Module shall support keypads and integrated keypad readers. 3. Single Reader I/O Module shall support connectivity and interface with a system arm / disarm functionality using a standard keypad/display terminal/card reader with features for User command and key selection. The Single Reader I/O Module shall support down loads from the SCP to the display of the keypad for date and time, zone status, error messages and User defined special text messaging. 4. All hardware interface and card format settings shall be loaded through software commands from the specified system software to associated SCP modules to each Single Reader I/O Module. 5. The Single Reader I/O Module shall provide two (2) on board fully supervised monitoring points (inputs). These monitoring points shall be configured as follows: (1) Monitoring point shall be dedicated for access portal status (contact inputs). (1) Monitoring points shall be dedicated for exit request inputs (manual or automated egress). 6. Single Reader I/O Module input monitoring point settings shall be User defined as normally open, normally closed or supervised normally open or normally closed. At a minimum input supervision shall be a series parallel 1/4W, 1%, 1K by 1K Ohm resistor circuit. 7. The Single Reader I/O Module shall provide two (2) on board output relays for controlling electrified devices or switching inputs. These relays shall be configured as follows: (1) Relay shall be dedicated for the electric portal locking device. (1) Relay shall be auxiliary and fully User defined for controlling or switching other devices or points within the site as required by design and indicated on the drawings. 8. Single Reader I/O Module output relays shall allow configuration for fail safe or fail secure operation and shall support ON, OFF, and PULSE, command states. 9. In the event of a communication failure with a System Control Processor (SCP), the Single Reader I/O Module shall be capable of locally processing access requests based on facility code verification. 10. The Single Reader I/O Modules operational programming shall be stored in non-volatile Flash Memory allowing for on-line program upgrades. 11. Single Reader I/O Module shall utilize IEEE standard two-wire RS-485 communications with data rates up to 38,400KBps up to an IEEE standard of 4000 feet.
C.
Each Single Reader I/O Module shall be installed either in a dedicated enclosure or share an enclosure with other associated access, input and output control modules. 1. Single Reader I/O Module shall have a dedicated cabinet tamper input. 2. Single Reader I/O Module shall have a dedicated power monitor input.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 13
ACCESS CONTROL
3. 4. D.
When sharing an enclosure with other associated access control system modules, only one of the modules in the enclosure shall be required to monitor cabinet tamper and power fail inputs. Up to 32 Single Reader I/O Modules shall be allowed to connect with any SCP within the system.
The Single Reader I/O Module shall meet the following physical specifications, excluding the required enclosure. 1. Input voltage: 12-24 Vdc, +/- 10%, 150 mA 2. Primary Port: 2-wire RS-485 3. Reader Port: 1, TTL, Wiegand and RS-485, bi-color LED and Buzzer Support, keypad multiplexed with card data 4. Inputs: 2 fully supervised (Portal Contact and Request to Exit) a. 2 un-supervised (Cabinet Tamper / Power Monitor) 5. Outputs: 2 General Purpose Relays a. 1 Lock Control - Form-C, 5 Amp 28 VDC b. 1 Auxiliary - Form-C, 1Amp 28 VDC 6. Temperature:0 degrees F to 70 degrees F, operating 7. Relative humidity:0 percent to 95 percent, non-condensing
2.09 ACCESS CONTROL DUAL READER I/O MODULE (RS-485 NETWORK) A.
The System Control Processor (SCP) shall provide distributed processing and management for each Dual Reader I/O Module incorporated in the system.
B.
The Dual Reader I/O Module shall meet the following, minimum, design and performance specifications. 1. Dual Reader I/O Module shall support security industry standard TTL, Wiegand, RS-485 and OSDP protocol. 2. Dual Reader I/O Module shall support keypads and integrated keypad readers. 3. Dual Reader I/O Module shall support connectivity and interface with a system arm / disarm functionality using a standard keypad/display terminal/card reader with features for User command and key selection. The Dual Reader I/O Module shall support down loads from the SCP to the display of the keypad for date and time, zone status, error messages and User defined special text messaging. 4. All hardware interface and card format settings shall be loaded through software commands from the specified system software to associated SCP modules to each Dual Reader I/O Module. 5. Dual Reader I/O Module shall support up to two (2) security industry standard readers and/or data entry/display terminals (keypad with display) for access or egress authorizations. 6. Dual Reader I/O Module shall support different reader technologies on the same module, User defined. 7. Dual Reader I/O Module reader ports shall provide up to 150 mA of unregulated 12 Vdc power for each reader. At a minimum card/data input support shall be Wiegand, TTL or RS-485 format. Single and dual wire LED output shall be provided supporting bicolor display. Reader buzzer support shall also be provided. 8. Dual Reader I/O Module shall provide eight (8) on board fully supervised monitoring points (inputs). These monitoring points shall be configured as follows: (2) Monitoring points shall be dedicated for access portal status (door contact inputs) one per reader port. (2) Monitoring points shall be dedicated for exit request inputs (manual or automated egress) one per reader port. (4) Monitoring points shall be auxiliary and fully User defined for monitoring other devices or points within the site as required by design and indicated on the drawings. 9. Dual Reader I/O Module input monitoring point settings shall be User defined as normally open, normally closed or supervised normally open or normally closed. At a minimum input supervision shall be a series parallel 1/4W, 1%, 1K by 1K Ohm resistor circuit.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 14
ACCESS CONTROL
10. Dual Reader I/O Module shall provide six (6) on board output relays for controlling electrified devices or switching inputs. These relays shall be configured as follows: (2) Relays shall be dedicated for electric portal locking device control one per reader port. (4) Relays shall be auxiliary and fully User defined for controlling or switching other devices or points within the site as required by design and indicated on the drawings. 11. All Dual Reader I/O Module output relays shall be Form-C, 5A@28 Vdc, resistive relays. 12. All Dual Reader I/O Module output relays shall allow configuration for fail safe or fail secure operation and shall support ON, OFF, and PULSE, command states. 13. In the event of a communication failure with a System Control Processor (SCP), the Dual Reader I/O Module shall be capable of locally processing access requests based on facility code verification. 14. The Dual Reader I/O Modules operational programming shall be stored in non-volatile Flash Memory allowing for on-line program upgrades. 15. Dual Reader I/O Module shall utilize IEEE standard two-wire RS-485 communications with data rates up to 38,400KBps up to an IEEE standard of 4000 feet. C.
Each Dual Reader I/O Module shall be installed either in a dedicated enclosure or share an enclosure with other associated access control system modules. 1. Dual Reader I/O Module shall have a dedicated cabinet tamper input. 2. Dual Reader I/O Module shall have a dedicated power monitor input. 3. When sharing an enclosure with other associated access, input and output control modules, only one of the modules shall be required to monitor cabinet tamper and power fail inputs. 4. Up to 32 Dual Reader I/O Modules shall be allowed to connect with any SCP within the system.
D.
The Dual Reader I/O Module shall meet the following physical specifications, excluding the required enclosure. 1. Input voltage: 12-24 Vdc, +/- 10%, 550 mA 2. Primary Port: 1 Down/Up line 2-wire RS-485 3. Reader Ports: 2, TTL, Wiegand & RS-485, bi-color LED & Buzzer Support 4. Inputs:8 fully supervised 5. Output Relays:6 Form-C 5 Amp 30 VDC 6. Inputs: Two dedicated unsupervised tamper and power monitor 7. Temperature: 0 degrees F to 70 degrees F, operating 8. Relative humidity: 0 percent to 95 percent, non-condensing
2.10 ACCESS CONTROL SIXTEEN CHANNEL INPUT MODULE (RS-485 NETWORK) A.
The Sixteen Channel Input Module shall interface sixteen (16) auxiliary general purpose fully supervised input monitor points and two (2) control relays for security monitoring and device control through the (SCP) and HOST software.
B.
The Sixteen Channel Input Module shall meet the following, minimum, design and performance specifications. 1. Sixteen Channel Input Module input point settings shall be User defined as normally open, normally closed or supervised normally open or normally closed. At a minimum input supervision shall be a series parallel 1/4W, 1%, 1K by 1K Ohm resistor circuit. 2. The Sixteen Channel Input Module shall provide two (2) User defined relays for controlling electrified devices or switching inputs. These relays shall support ON, OFF and PULSE command states. 3. The Sixteen Channel Input Module output relays shall be Form-C, 5A@30 Vdc, resistive relays. 4. The Sixteen Channel Input Module operational programming shall be stored in non-volatile Flash Memory allowing for on-line program upgrades. 5. The Sixteen Channel Input Module shall utilize IEEE standard two-wire RS-485 communications with data rates up to 38,400KBps up to an IEEE standard of 4000 feet.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 15
ACCESS CONTROL
C.
Each Sixteen Channel Input Module shall be installed either in a dedicated enclosure or share an enclosure with other associated access control system modules. 1. The Sixteen Channel Input Module shall have a dedicated cabinet tamper. 2. The Sixteen Channel Input Module shall have a dedicated power monitor. 3. When sharing an enclosure with other SIO modules, only one of the modules shall be required to monitor cabinet tamper and power fail inputs.
D.
The Sixteen Channel Input Module shall meet the following physical specifications, excluding the required enclosure. 1. Input voltage: 12-24 Vdc, +/- 10%, 350 mA 2. Primary Port 1: Down/Up line 2-wire RS-485 3. Inputs: 16 supervised, 2 unsupervised (tamper/power monitor) 4. Output Relays: 2 Form-C 5 Amp @ 28 VDC 5. Down-line: 2-wire RS-485 6. Temperature:0 degrees F to 70 degrees F, operating 7. Relative humidity:0 percent to 95 percent, non-condensing
2.11 ACCESS CONTROL SIXTEEN CHANNEL RELAY MODULE (RS-485 NETWORK) A.
The Sixteen Channel Relay Module shall interface sixteen (16) auxiliary general purpose control relays for device control through the (SCP) and HOST software.
B.
The Sixteen Channel Relay Module shall meet the following, minimum, design and performance specifications. 1. The Sixteen Channel Relay Module shall provide sixteen (16) on board output relays for controlling electrified devices or switching inputs. These relays shall be auxiliary and fully User defined for controlling or switching other devices or points within the site. 2. The Sixteen Channel Relay Module output relays shall be Form-C, 5A@30 Vdc, resistive relays. 3. The Sixteen Channel Relay Module output relays shall allow configuration for fail safe or fail secure operation and shall support ON, OFF, and PULSE, command states. 4. The Sixteen Channel Relay Module operational programming shall be stored in non-volatile Flash Memory allowing for on-line program upgrades. 5. The Sixteen Channel Relay Module shall utilize IEEE standard two-wire RS-485 communications with data rates up to 38,400KBps up to an IEEE standard of 4000 feet.
C.
Each Sixteen Channel Relay Module shall be installed either in a dedicated enclosure or share an enclosure with other associated access control system modules. 1. The Sixteen Channel Relay Module shall have a dedicated cabinet tamper. 2. The Sixteen Channel Relay Module shall have a dedicated power monitor. 3. When sharing an enclosure with other associated access, input and output control modules, only one of the modules shall be required to monitor cabinet tamper and power fail inputs.
D.
The Sixteen Channel Relay Module shall meet the following physical specifications, excluding the required enclosure. 1. Input voltage: 12-24 Vdc, +/- 10%, 1100 mA 2. Primary Port 1: Down/Up line 2-wire RS-485 3. Output Relays: 16 Form-C 5 Amp @ 30 VDC 4. Inputs: Two dedicated unsupervised tamper and power monitor 5. Temperature:0 degrees F to 70 degrees F, operating 6. Relative humidity:0 percent to 95 percent, non-condensing
2.12 ACCESS CONTROL EIGHT CHANNEL MULTIPLEXER (RS-485 NETWORK) A.
The Eight Channel Multiplexer (ECM) shall provide additional IEEE RS-485 communications channels for use between the (SCP) and associated SIO sub-control modules.
B.
The ECM shall meet the following, minimum, design and performance specifications. 1. ECM shall provide eight two-wire RS-485 communication channels from a single RS-232 or RS-485 data input channel.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 16
ACCESS CONTROL
2. 3.
ECM shall have automatic fault port partitioning in order to protect the integrity of the communication bus. ECM shall provide for both star and home-run configurations with operating distances, on each channel, of up to the IEEE standard of 4000 feet.
C.
Each ECM shall be installed either in a dedicated enclosure or share an enclosure with other associated SCP, access, input and output system modules.
D.
The ECM shall meet the following physical specifications, excluding the required enclosure. 1. Primary Port: RS-485 or RS-232 2. Down-line Ports:3, 5, 7, 9 RS-485 Transmit/Receive 3. Down-line Ports:2, 4, 6, 8 RS-485 Transmit/Receive or Receive only 4. Input voltage:12 Vdc, +/- 10%, 250 mA 5. Temperature:0 degrees F to 70 degrees F, operating 6. Relative humidity:0 percent to 95 percent, non-condensing
2.13 ACCESS CONTROL CARD READER A.
The access control card readers shall interface with the access control reader modules and the door control hardware, as specified in other applicable sections of this specification.
B.
The card reader shall meet the following, minimum, design and performance specifications. 1. Reader technology shall be proximity technology as required by Owner. 2. Reader shall be weatherproof type when installed in exterior or other wet environments. 3. Reader shall communicate with the reader I/O modules using the industry standard Wiegand interface or RS-485 OSDP protocols. 4. Reader shall operate on 12VDC or 5VDC power from the reader I/O modules at a maximum current rating of 150 mA per reader.
C.
The card reader type and model shall be provided to meet the exact needs of each entry point by design and indicated on the drawings.
D.
The system vendor shall supply a reader application schedule indicating each reader, as referenced on the drawings, and specifying type and model. This schedule shall be supplied with the submittal package as required in the submittal section of this technical specification.
E.
Submit reader cut sheets as required in the submittal section of this technical specification.
2.14 SERIAL ENABLES AUTO-DIAL SOLUTION MODULE (SEADS) A.
SEADS shall provide the following functions: 1. SEADS shall provide an industry standard IEEE RS-232 communication link between a local SCP and a non-proprietary SEADS module, a field-programmable, seven-zone, alarm digital communicator transmitter. 2. SEADS shall provides four supervised hardwired alarm zones used to monitor general alarm or event singles per defined by the User as site conditions. SEADS shall provide output relays for power failure and trouble conditions that can be linked to other I/O monitoring devices. 3. SEADS shall use the widely available public switched telephone network (PSTN) for efficient reporting of alarms and events to a central monitoring location or multiple locations. 4. SEADS shall facilitate point-specific alarm reporting enabling highly accurate responses through off-site annunciation. Local reporting and response shall be standard with full operator management and control of all SEADS reporting. 5. SEADS shall be provided with default settings to minimize the setup / configuration. 6. SEADS provides general alarm and general trouble contact outputs. The alarm output shall indicate serial port-derived events that are pending transmission, and input zone activations. The trouble output shall indicate telephone line faults, communicator faults, serial port faults as well as input zone and power faults. These SEADS outputs may be monitored or simply provide local fault indications.
B.
SEADS shall provide the following features:
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 17
ACCESS CONTROL
1.
SEADS shall be a non-proprietary alarm microprocessor and incorporate an ASCII data-to-SIA converter as well as seven hardwire zones operated as a digital communicator. 2. SEADS shall include a programming utility that requires only a PC with a serial port and an appropriate cable to setup and configure the module. 3. SEADS shall use standard SIA event code protocol for communication to any User selected central station using an industry standard alarm receiver. 4. SEADS primary alarm reporting shall be accomplished through the SCP serial connection. Secondary alarm reporting shall be available using the four EOL-resistor supervised zone inputs 1 through 4 and three unsupervised zones 5-6 and 7 on the SEADS module. Unsupervised zones shall be AC power fail and no/low battery output contacts from the external power supply. 5. SEADS zone reporting shall use standard SIA event codes. 6. SEADS shall provide test code call-in cycles may be programmed for either 4 or 24 hours and transmit both normal and off-normal condition test codes. 7. SEADS shall provide telephone line(s) supervision and faults are reported using standard SIA event codes. 8. SEADS shall provide for alternate trouble reporting using separate telephone numbers and in addition shall provide distinct audible sounds for trouble and alarm, with 24-hour trouble resounding as required by UL 864. 9. SEADS shall provide line seizure for use with shared phone lines. 10. SEADS shall provide for a manual test button, a silence pushbutton to deactivate audible signals, a program pushbutton to invoke a programming session and a CPU reset button. 11. SEADS local LED's and audible tones shall clearly indicate module status. 12. SEADS alarm and event codes for the hardwired zone inputs may be programmed by the User. C.
The SCP shall meet the following physical specifications, excluding the required enclosure. 1. Phone lines: 2 each RJ-45 receptacles 2. Hardwired zone inputs: 7 (4-EOL resistor supervised) 3. EOL resistor value: 10K Ohms 4. Maximum Line Resistance: 2K Ohms 5. Relays: a. 2 SPDT 2A @ 30Vdc or 1A @120Vac b. 1 Common Alarm c. 1 Common Trouble 6. LED Indicators: a. 1 Green 24Vdc Power Indicator b. 1 Yellow External Power Trouble c. 4 Red Zone Alarm for Supervised Inputs d. 4 Yellow Zone Trouble for Each Input e. 1 Red Serial Port Pending Transmission f. 1 Yellow Serial Port Fault Alert g. 2 Yellow Trouble for Telephone Lines h. 1 Red Active Telephone Lines i. 1 Red Relay Active for Each Relay 7. Audible device: Rated at 92 DB 8. Ringer Equivalence: 0.1 9. FCC registration # US:YES 10. Power Requirements:16-32 Vdc Filtered, Reg. or Un-reg. 11. Current requirements:Idle and Alarm: 100mA, 250mA 12. Circuit Board Size:6” H x 10.5” W 13. Weight: 11 oz 14. Optional Enclosure:14” H x 17” W x 4” D - Gray 15. Pushbuttons: Reset, Manual Test, Silence & Program
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 18
ACCESS CONTROL
16. User controls:Jumpers (8 total): a. J1 & J2: Configure RS-232 port handshake lines. b. J3: Audible device disconnect jumper physically disconnects power from the device c. J4: Removed Disables supervision of serial port. d. J5-J7: Set the normal condition of auxiliary power monitor (zones 5-7 respectively) e. J8: Installed - Sets 2 hour transmission delay for zone 5 (AC power fail), Uninstalled No delay 17. User-programmable items: a. Number of Telephone Lines Installed b. Primary telephone number c. Secondary telephone number d. Sends Trouble signals to secondary phone# e. Primary account number f. Secondary account number g. Daily test time-of-day h. Daily test check-in interval i. Event codes for all zones j. Real time clock 18. SIA transmitter: Transmits all events that are in the SIA transmit queue (multiple events per call), per SIA Digital Communication Standard of November 1991. Transmissions will be in accordance with the requirements of a Level 1 transmitter as defined in Section 5 (compatibility), Table 3 (SIA digital compatibility levels) - (SIA20). 19. Temperature requirements: 0 degrees F to 70 degrees F, operating 20. Relative humidity: 0 percent to 95 percent, non-condensing 2.15 ACCESS CONTROL DATA ENTRY/DISPLAY TERMINAL (RS-485 NETWORK-READER / SIO) A.
The access control data entry/display terminal shall interface with a Single or Dual Reader I/O Module, as specified by design and indicated on the drawings.
B.
The data entry/display terminal shall meet the following, minimum design and performance specifications. 1. Entry/Display Terminal shall have a two (2) line backlit display supporting sixteen (16), 7.5mm high characters per line. 2. Entry/Display Terminal shall have a sixteen (16) button backlit keypad supporting both standard numeric keys and four (4) programmable function keys. The programmable function keys shall be User configurable for up to 8 separate command functions. 3. Entry/Display Terminal shall display time in 12- or 24-hour format. 4. Entry/Display Terminal firmware shall be FLASH memory. 5. Data entry/display terminal shall be either surface mounted or mount over a 3-gang box. 6. Entry/Display Terminal shall utilize two-wire RS-485 communications with speeds up to 38,400KBps up to 4000 feet.
C.
Entry/Display Terminal shall support one (1) internal or external reader. 1. Entry/Display Terminal reader port shall provide up to 150 mA of unregulated 12 Vdc power for a card reader, a card/data input supporting Wiegand or RS-485 format, two-wire or one-wire LED output with bicolor support, and buzzer output.
D.
The data entry/display terminal shall meet the following, physical specifications. 1. Input voltage:12 Vdc, +/- 15%, 175 mA 2. Keypad Port:TTL, RS-485 3. Reader Port:Wiegand, Clock and Data 4. Temperature:0 degrees F to 70 degrees F, operating 5. Relative humidity:0 percent to 95 percent, non-condensing
2.16 ACCESS CONTROL SYSTEM SOFTWARE OPTIONS A.
The system shall provide the following software options for User incorporating into the system as required. A list of the optional applications requires are as follows:
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 19
ACCESS CONTROL
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
Single software license for adding client workstation to the system for administration, management and response. Single software license for integrating third party CCTV matrix product. Single software license for integrating third party DVR/NVR product. Single software license for integrating third party Intercom product. Single software license for integrating multiple bar code fonts for badging. Single software license for integrating third party burg panel. System wide Software License for integrating personnel ID photo badging. System wide software license for integrating biometrics readers. System wide software license for integrating WiFi IP Locksets. System wide software license for integrating smart card encoding. System wide software license for Importing and Exporting of user database. System wide software license for Time and Attendance electronic reporting feature. System wide software license for terminal services support of remote terminal. Thin client support (User pre-authorized access) System wide software license for web browser operator access into the system software (User pre-authorized access). System wide software license for User report development and management. (Recommended for DBA only) System wide software license for User defined software data base segregation.
2.17 WIRELESS KEYPAD / PROXIMITY LOCKS A.
Reader Lock/Trim 1. Integrated smart locking device with its own database. 2. Capability to make all decisions at the door. 3. Reader / Lock/ Trim to be installed within the existing door ANSI cut out. There shall be no need to rout out the door to drive additional power through any electric transfer hinge. All requirements will be met within the reader / lock itself. 4. Wireless Reader shall use an AA battery pack; no AC power shall be required at the door. 5. The doors with monitor status only will transmit a wireless signal from the door contact to the WAC to monitor door status. No Card access is possible thru these doors. 6. Wireless Locks will communicate on an 802.15.4 frequency allocated so as not to be affected by standard traffic on 802.11 systems. 7. The reader / lock shall also be able to operate as a fully stand alone intelligent device making all the decisions in real time. In the unlikely event that the reader/lock is offline from the host, it shall continue to operate, storing and recording accesses until it is re-connected and back online to the host. The wireless reader/ lock shall be offered in one of four modes. 8. As a supplemental exit device trim to be added to an existing exit devices. 9. As a wireless access controller interfaced to a hardwired reader and ancillary door devices such as an electric locking device, Request to Exit (RQE) switch, a Door Switch Monitor and a Door lock sense input. 10. For exit device applications the wireless reader shall provide support for an integral Request to Exit (RQE) switch, Door Position switch (DS) and Latchbolt Position switch (LS). 11. The reader Trim / lock shall support as a minimum the following “reader” technologies: a. Support for 125 KHz. HID and Indala compatible Proximity cards with variable bit formats such that multiple user defined bit formats can be supported at the reader b. As standard, the reader shall support exterior applications c. Each reader / lock shall have battery power to meet 100,000 lock / transactions d. Each reader lock shall come with a minimum of 2,000 ID capacity, and be able to store locally, if offline, up to 10,000 transactions
B.
Reader Trim/ Lock database 1. The reader shall support 2,000 unique ID’s in its standard configuration and be expandable to 65,000. Expansion shall not require a field upgrade at the reader but rather a software
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 20
ACCESS CONTROL
2. 3. 4. 5. 6. 7.
key shall be downloaded from the host that shall increase the database size and support up to 65,000 cardholders. The reader shall support up to 8,000 transactions in the event the lock cannot communicate to the portal gateway. Up to 512 Time Zones per user group with up to 6 time intervals per time code. Up to 32 types of unique user defined holidays shall be supported. Each holiday shall be capable of supporting a different time code. A unique set of Access privileges shall be available for each cardholder per reader / lock The memory allocation on the reader / lock shall be dynamic such that the user may maximize the size of the available memory to meet their requirements for either ID’s or transaction storage Time zones shall be able to cross midnight such that a shift beginning at 10:00 PM and ending at 9:00 AM the next morning, will be considered as a single time zone The reader/lock shall be able to support an auto-enroll mode where the user may select a reader to be used to enroll a large group of cardholders. This shall be achieved by either bulk loading card ID numbers between a specific range or by presenting a card to a reader that then reads the card data and enrolls the card into the database.
C.
Reader Trim/ Lock Operation Modes 1. The reader will support Access control for a single door with one reader and free egress on the same door 2. The reader will monitor a door position status such that it is able to detect door open and door locked and secure. In no event will a separate contact be required to be mounted to the frame of the door and wired back to a separate contact monitoring device. All alarm monitoring at the door / portal will be monitored by the reader / lock itself and shall not require any additional controller support 3. The reader shall report any access transaction with the date and time of the event in Hours: Minutes and Seconds 4. The reader locks database shall support up to 7 unique shunt times for specific groups of individuals and meet ADA compatibility requirements for extended shunt times for any single or groups of physically impaired cardholders 5. The reader will support an RQE (Request to Exit) status that will be reported separately as a separate auditable transaction. In the event that an attempt to exit is made, but the door /portal remains closed (secure), then the transaction will not be recorded as a valid RQE and will time out after the shunt time has expired 6. The reader/ lock shall support and transmit a signal if the power to the reader / lock drops below 10% 7. The reader shall support different operation modes based on time zones. Thus a reader may be in a Card only mode in the daytime, but require Card plus PIN after hours. This shall be fully user programmable from the host 8. The reader / lock shall be able to operate in a fully stand alone mode or as a distributed fully intelligent reader/ lock holding the transactions until they are polled 9. The reader / lock shall communicate via spread spectrum radio transmission at 2.4 GHZ 10. The reader / lock shall use as a standard, AES 128 bit encryption between to the nearest non-dedicated Portal Gateway. Portal Gateways shall provide redundant communications capability so that a wireless reader can report to another Portal Gateway if primary reporting path is lost 11. The reader / lock shall report multiple incorrect PIN attempts (greater than 3) as an alarm attempt 12. The proximity reader / lock shall be able to detect the presence of a proximity card, such that the cardholder shall not be required to orient their card in a specific manner to wake up the reader 13. The readers read / response time to an access request shall not exceed 250 Milliseconds worse case 14. Each reader lock shall have its own unique MAC address
D.
Wireless Access Controller
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 21
ACCESS CONTROL
1.
The reader will support Access control for a single door with one reader and free egress on the same door 2. A wireless access controller shall be capable of interfacing with a token reader utilizing a standard Wigand protocol to unlock various electrified locking hardware such as electric strikes, exit device trim, electro-magnetic locks and other low voltage applications. It shall also serve as a retrofit kit to replace an existing wired infrastructure with a local wireless reader PCB that has the ability to slave to a wired reader and local peripherals at the door 3. Support an existing Request to Exit switch (RQE), Door Position switch and Latchbolt Position switch (LS). 4. Support a locally powered locking device rated up to 4 AMPS at 12/24V DC 5. Auxiliary relay output will be available to drive other door related outputs. This relay shall be rated at 2 AMPS 12/24 V DC 6. The wireless access controller will also have the same feature set of software capabilities as the standard wireless reader for up to 65,000 ID’s, 144 Time Zones, variable shunt times for different staff groups, and ADA compliance 7. The wireless access controller will be able to support any Wigand card format from 16 to 128 bits and shall be able to serve as a log on or enrollment reader where an individual or group of individuals may “badge” into the system and the system will identify their card data so the card can be auto-enrolled 8. The wireless access controller shall provide wireless communications back to a Portal Gateway such that no separate controllers will be required for decision making. All door related decisions will be made at the wireless access controller local to the reader(s) it serves 9. All terminations to the wireless access controller shall be through plug in wired block terminals - no special tools will be required to install the unit(s) 10. The reader shall be able to operate in different modes such that it is able to serve as a smart I/O module supporting I/O functions either as ancillary services to it’s primary role as an access control device or as it’s sole role. In this mode the wireless access controller shall be able to provide the following: a. As a wireless reader module with support for a dedicated Door Position switch (DS), Latchbolt Position switch (LS), Request to Exit (RQE), and key by pass override with two onboard relays, one rated at 4 Amps for 12/24V DC operation, the other at 2 Amps for 12/24V DC operation b. Wireless module with 4 supervised inputs, 4 non-supervised inputs, two onboard relays with one rated at 4 Amps for 12/24V DC operation, the other at 2 Amps for 12/24V DC operation c. As a wireless module with 4 supervised inputs, two onboard relays with one rated at 4 Amps for 12/24V DC operation, the other at 2 Amps 12/24V DC operation plus 4 additional logic driven outputs. In this mode no wireless readers would be supported. 11. Wireless Access Controller shall come standard with half wave dipole antennas and a ceiling mount omni directional antenna with 20’ of cable and all required connectors 12. Portal Gateways: The portal gateways shall operate in a non-dedicated mode such that any reader / lock shall be able to report to and through any portal gateway. The portal gateways shall accept data from any of the addressed readers and transmit bi-directional encrypted data to the host for archiving and data management. Each portal gateway shall have the following capabilities. a. Each portal gateway, in base configuration, shall support a minimum of 16 reader / locks in it’s antenna range and via system options, be able to support up to 128 reader / locks in a maximum system configuration b. Each portal gateway shall have it’s own unique MAC address such that, on boot up, the host will find and identify those portal gateways that belong to the system c. Every portal gateway shall encrypt the data using 128 BIT AES encryption and send and receive data via spread spectrum RF transmission to and from the host d. Nominal transmissions distances between the reader / locks and the portal gateway(s) shall be 250 feet line of sight. Extended ranges exceeding 1000’ shall be
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 22
ACCESS CONTROL
e. f.
g. h. i.
available, if required, using standard commercially available high security RF transport sub-systems Each portal gateway shall, as an option, have the support of a stand-by power supply Each portal gateway shall support three transmission paths to the host. The user may elect to use standard Ethernet cabling between the portal gateway and the host using a cross over cable. Standard Ethernet using local hubs and routers, or they may elect to use a wireless (MESH) network infrastructure to provide a wireless, redundant communications backbone Each portal will have its own static IP address The portal Gateway shall support secure socket communications between the host(s) / server and any associated Portal Gateway. This shall be user selectable The portal gateway shall come standard with half wave dipole antennas and a ceiling mount omni directional antenna with 20’ of cable and all required connectors.
2.18 PROXIMITY CARD READERS FOR NEW SYSTEMS A.
Provide ADA compliant reader with bicolor LED which is illuminated red or green to indicate operational status.
B.
Reader may be located up to 500 feet away from main controller.
C.
Proximity reader will allow access by presenting a card within 4 inches of the reader.
D.
Manufacturer HID or approved.
E.
Model Numbers: RP40 or RP15 Multiclass Reader
2.19 PROXIMITY CARD READERS FOR EXISTING SYSTEMS A.
Provide ADA compliant reader with bicolor LED which is illuminated red or green to indicate operational status.
B.
Reader may be located up to 500 feet away from main controller.
C.
Proximity reader will allow access by presenting a card within 4 inches of the reader.
D.
Provide Reader that is compatible with existing readers and proximity cards on existing system.
E.
Verifiy exsiting card and reader type with owner.
2.20 REQUEST TO EXIT DEVICE A.
Provide a passive infrared sensor or door hardware for unalarmed egress.
B.
REX device shall be programmed to shunt alarm only and shall not physically unlock door, Activation of REX device shall not be recorded in event log.
C.
Manufacturer: Detection Systems, Kantech, GE or approved.
2.21 MAGNETIC DOOR CONTACTS A.
Provide ¾-inch diameter self-locking magnetic contacts.
B.
Coordinate with architectural door hardware requirements.
C.
Manufacturer: Sentrol 1078 Series, or approved.
2.22 MAGNETIC DOOR CONTACTS A.
Use only for Marion County Courthouse Half Doors
B.
Provide Surface Mount Door Contact
C.
Coordinate with architectural door hardware requirements.
D.
Manufacturer: Sentrol 1082 or 1085 Series, or approved.
2.23 BACKUP BATTERY A.
Provide Backup Battery capable of powering system for a minimum of 72 hours with out power.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 23
ACCESS CONTROL
PART 3 EXECUTION 3.01 INSTALLATION A.
Install in accordance with manufacturer's instructions.
B.
Limited energy low-voltage cabling, per manufacturer's recommendation.
C.
Make conduit and wiring connections to door hardware devices furnished and installed under Section 08 71 00.
D.
Supervision for all field devices to be located at the end of the line and not in the head end panels.
3.02 FIELD QUALITY CONTROL A.
Perform field inspection and testing in accordance with State of Oregon General Conditions for Public Improvements Contracts.
B.
Manufacturer Services: Furnish services of technician to supervise installation, adjustments, final connections, system testing, and to train Owner personnel.
3.03 CLOSEOUT ACTIVITIES A.
Demonstrate normal and abnormal modes of operation, and required response to each.
B.
For New Systems Provide (50) HID 1326 Prox Card II Clamshell Cards and (50) HID 1324 Adhesive Labels.
C.
For Existing Systems Provide (50) Prox Cards or Fobs that are compatible with existing readers and cards or fobs. Verify typoe with owner.
D.
Provide the following instruction to designated Owner personnel: 1. Hands-On Instruction: On-site, using operational system. 2. Classroom Instruction: Owner furnished classroom, on-site or at other local facility.
E.
Provide 6 hours of training at each facility to designated Owner personnel covering issues for the topics below. Duration of individual training sessions as determined by Owner, not to exceed total number of required hours. 1. Administrative: Issues necessary for non-technical staff. 2. Basic/Detailed Operation: Issues necessary for attendant personnel, security officers. 3. Maintenance Technicians: Issues necessary for electrical technicians on programming, maintaining, repairing, and modifying.
F.
Furnish the services of instructors and teaching aids; have copies of operation and maintenance data available during instruction.
G.
Provide sign-in sheet and means of evaluation of trainees suitable to type of training given; report results to Owner.
3.04 PROGRAMING A.
Coordinate all programmable system functions with Owner prior to execution, including but not limited to: scheduling, card input and access levels, zoning, logging, client setup, authorization levels, etc. Provide all programing and startup services as required to satisfy the Owner.
3.05 MAINTENANCE A.
See State of Oregon General Conditions for Public Improvements Contracts for additional requirements relating to maintenance service.
B.
Provide a separate maintenance contract for specified maintenance service.
C.
Furnish service and maintenance of security access system for one year from Date of Substantial Completion. END OF SECTION 28 13 00
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 13 00 - 24
ACCESS CONTROL
SECTION 28 16 00 DURESS ALARM SYSTEM PART 1 GENERAL 1.01 SECTION INCLUDES A.
Duress devices.
B.
Alarm control panel.
C.
Signaling devices.
1.02 RELATED REQUIREMENTS A.
Section 26 05 19 - Low-Voltage Electrical Power Conductors and Cables (600 V and Less).
1.03 SCOPE OF WORK A.
All controllers, control boards, housings, mounts, keypads, duress buttons, wiring, software, programing and any other required hardware to be supplied by Contractor.
B.
120 volt power sources to be provided by Contractor.
1.04 REFERENCE STANDARDS A.
NFPA 70 - National Electrical Code; National Fire Protection Association; Most Recent Edition Adopted by Authority Having Jurisdiction, Including All Applicable Amendments and Supplements.
B.
NFPA 72 - National Fire Alarm Code and Signaling Code; National Fire Protection Association; 2010.
C.
UL 365 - Police Connect Burglar.
D.
UL 609 - Local Burglar.
E.
UL 1610 - Central Station Burglar Alarm Units.
F.
UL 1635 - Digital Burglar Alarm Communicator System Units.
1.05 SYSTEM DESCRIPTION A.
Duress Alarm System: Notify a Central Station and local annunciation if duress button is activated. Annunciate alpha numeric description of each duress button both locally and to the Central Station.
1.06 SUBMITTALS A.
See State of Oregon General Conditions for Public Improvements Contracts for submittal procedures.
B.
Shop Drawings: Indicate system wiring diagram showing each device location and wiring connection required. Document all proposed exposed wiring and associated wiring method. See Section 26 05 05.
C.
Product Data: Provide electrical characteristics and connection requirements.
D.
Test Reports: Indicate satisfactory completion of required tests and inspections.
E.
Manufacturer's Installation Instructions: Indicate application conditions and limitations of use stipulated by product testing agency. Include instructions for storage, handling, protection, examination, preparation, installation, and starting of product.
F.
Project Record Documents: Record actual locations of initiating devices, signaling appliances, and end-of-line devices. See Section 26 05 05.
G.
Operation Data: Operating instructions.
H.
Maintenance Data: Maintenance and repair procedures.
1.07 QUALITY ASSURANCE A.
Conform to requirements of NFPA 70.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 16 00 - 1
DURESS ALARM SYSTEM
B.
Manufacturer Qualifications: Company specializing in manufacturing the products specified in this section.
C.
Products: Furnish products listed and classified by Underwriters Laboratories Inc. as suitable for purpose specified and indicated.
PART 2 PRODUCTS 2.01 MANUFACTURERS A.
Duress System: 1. Digital Monitoring Products, Inc. (DMP); Product: XR500 series www.dmp.com. 2. Bosch Security Systems; www.boschsecurity.us. 3. DSC; www.dsc.com. 4. Substitutions: See State of Oregon General Conditions for Public Improvements Contracts.
2.02 DURESS ALARM CONTROL PANEL A.
Control Panel: Modular construction with surface wall-mounted enclosure. Where exposed pins, the hinges shall be of the tight pin type or the ends of hinge pins shall be tack welded to prevent ready removal. Doors having a latch edge length of less than 24 inches shall be provided with a single lock. Where the hinged door latch edge is 24 inches or more in length, doors shall be provided with three-point latching device with lock; or alternatively with two locks, one located near each end.
B.
Power supply: Adequate to serve control panel modules, remote detectors, and alarm signaling devices. Include battery-operated emergency power supply with capacity for operating system in standby mode for 24 hours.
C.
Electronic Components: All system electronic components shall be solid-state type, mounted on printed circuit boards. Light duty relays and similar switching devices shall be solid-state type or electromechanical. The panel shall have an over current notification LED that lights when devices connected to the Keypad Bus and LX-Bus(es) draw more current than the panel is rated for. When the over current LED lights, the LX-Bus (es) and Keypad bus are shut down.
D.
Remote Annuciators: The system shall support a maximum of sixteen (16) supervised remote annunciators with the identical capabilities, functions and display layout. Operation of the remote annunciators shall be limited to authorized users by the use of a code or key. The remote annunciators shall be capable of operating at a maximum wiring distance of 15,000 feet from the control unit on unshielded, non-twisted cable.
E.
Serial Interface: The control panel shall be capable of a serial interface to output information to a standard serial printer or serial interface to a communication port on a standard computer. Through control panel programming the system shall include a provision to allow the selection of which reports are to be output.
F.
Software: 1. The system shall interface with computer software with the capability to fully program the panel by connecting to the panel through: a. Direct cable connection interface card b. Receiver phone line connection c. Standard phone line connection d. Ethernet network connection e. Network connection across the Internet 2. The system shall interface with computer software capable of monitoring and logging all events. 3. The system shall interface with computer software capable of exporting reports in the following file formats: a. Excel spreadsheet (*.xls) b. Rich Text (*.rtf) c. Windows Metafile (*.wmf)
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 16 00 - 2
DURESS ALARM SYSTEM
4.
d. QuickReport (*.qrp) e. Text (*.txt) f. Comma-separated (*.csv) g. HTML document (*.htm) The system shall interface with computer software capable of printing custom, filtered reports including: a. All Events b. Zone Action c. Arming/Disarming d. Area Late to Close e. User Code Changes f. Door Access Granted g. Door Access Denied h. Opening/Closing Schedule Changes i. System Monitors j. System Events
G.
System Supervision: Provide electrically-supervised system, with supervised alarm initiating and alarm signaling circuits. Component or power supply failure places system in alarm mode.
H.
Initiating Circuits: Supervised zone module with alarm and trouble indication.
I.
Signal Circuits: Supervised zone coded signal module, sufficient for signal devices connected to system; occurrence of single ground or open condition places circuit in trouble mode and does not disable that circuit from transmitting alarm.
J.
Remote Station Signal Transmitter: Electrically supervised, capable of transmitting alarm and trouble signals over telephone lines to central station receiver.
K.
Auxiliary Relays: Provide sufficient SPDT auxiliary relay contacts for each detection zone to provide accessory functions specified.
L.
Trouble Sequence of Operation: Transmit non-coded signal to Central Station and remote annunciator panel.
M. Alarm Sequence of Operation: Actuation of duress device places system in alarm mode, which causes the following operations: 1. Sound and display local alarm signaling devices with non-coded signal. 2. Transmit non-coded signal to Central Station and remote annunciator panel. 3. Indicate location of actuated device on control panel and on remote annunciator panel. 4. Alarm Reset: Key-accessible reset function resets alarm system out of alarm if alarm initiating circuits have cleared. 5. Lamp Test: Manual lamp test function causes alarm indication at each zone at control panel and at annunciator panel. N.
Test Modes: 1. The system shall include a provision that permits testing from any alphanumeric keypad. The test shall include standby battery, alarm bell or siren, and communication to the central station. 2. The system shall include a provision for an automatic, daily, weekly, thirty (30) day, or up to sixty (60) day communication link test from the control panel installation site to the central station. 3. The system shall include a provision for displaying the internal system power and wiring conditions. Internal monitors shall include the bell circuit, AC power, battery voltage level, charging voltage, panel box tamper, phone trouble line 1, phone trouble line 2, transmit trouble, and network trouble.
O.
Communication: 1. The system shall be capable of signaling to as many as 8 remote monitoring station receivers. Seven (7) of the eight (8) paths shall be capable of being assigned as either a “primary” or “backup” path. In such a manor the system shall have multiple primary paths
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 16 00 - 3
DURESS ALARM SYSTEM
2.
3.
4. 5.
P.
to multiple remote monitoring stations as well as multiple backup paths to multiple monitoring stations. The system shall employ Adaptive Technology that allows a Backup communication path programmed for Network or Cellular to automatically ADAPT to the faster check-in rate of the Primary path should the Primary path become unavailable. This creates a seamless transition for communication. The system shall be capable of dialing up to (2) remote monitoring station receivers, four telephone numbers of 32 digits each using two separate switched telephone network lines such that if two unsuccessful attempts are made on the first line to the first number, the system shall make two attempts on first line to the second number. If these two attempts are unsuccessful, the system shall make two further attempts on the first line of the first number. After the tenth unsuccessful attempt, dialing shall stop and the alphanumeric keypad shall display trouble. Should another event occur that requires a report to be transmitted, the dialing sequence shall be repeated. The system shall have a programmable option to dial a second set of telephone numbers after the first ten attempts using the same sequence. The system shall be capable of communication using the IBM Synchronous Data Link Control format, and at least one other standard industry format. The system shall be capable of supporting Network communication with digital dialer backup, existing Ethernet data networks, satellite communication, fiber optic networks, local area networks, wide area networks, cellular communication, and retail data networks.
Network Communication: 1. The control panel shall be capable of asynchronous network communication with a retry time between 3 and 15 seconds for a total of one (1) minute. If communication is unsuccessful the control panel shall be capable of attempting backup communication through any of the available communication methods to the same receiver or a backup receiver. 2. The control panel shall employee adaptive communication technology. Adaptive Technology allows a Backup communication path programmed to use Network or Cellular to automatically ADAPT to the faster check-in rate of the Primary path should the Primary path become unavailable, creating a seamless transition for communication of messages. Select Adapt when programming the Checkin option. This allows a system to be fully supervised even if a path fails, while also keeping wireless charges low when the network is good. 3. Network communication between the control panel and the receiver shall be in a proprietary communication format. 4. The control panel shall be capable of supporting Dynamic Host Communication Protocol (DHCP) Internet Protocol (IP) addressing. 5. Underwriters Laboratories (UL) shall list network communication by the control panel for Grade AA High-Line Security. 6. The control panel shall be capable of two-way network communication using standard Ethernet 10BaseT in a LAN, WAN, or Internet configuration. 7. The control panel shall be capable of communication by means of a 128 Bit AES Rijndael Encryption process certified by NIST (National Institute of Standards and Technology) to an SCS-1R receiver with a built-in Encryption Alarm Router. 8. The control panel shall be capable of meeting DCID 6/9 and UL 2050 standards. 9. The control panel shall be capable of sending E-mail messaging to up to three E-mail accounts over network communications. 10. The control panel shall be capable of sending the following E-mail messages: a. Zone Alarms by Zone Name b. Zone Troubles by Zone Name c. Zone Bypass by User d. Arming (Closings) by User e. Disarming (Openings) by User f. Late to Close
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 16 00 - 4
DURESS ALARM SYSTEM
g. h. i. j. k. Q.
AC Power Trouble and Restoral System Low Battery Ambush Abort, Cancel and Alarm Verified by User Check-in by user
Panic Button Summary Test: 1. The system shall have the ability to test panic buttons without sending a panic alarm to the Central Station Receiver. 2. The system shall also have the ability to send panic zone test verification and failure results to the Central Station Receiver. 3. During the test, each time a panic zone trips, the display number shall increment and the keypad buzzer sound for two seconds. 4. The number of panic zones tripped shall constantly display until the test ends or no panic zone activity has occurred for 20 minutes. 5. When the Panic Zone Test ends and a zone failed (did not trip) during the test, the keypad shall be able to display the zone name and number and have the buzzer sounds for one second. Additional zone failed zones shall display when a button is pressed.
2.03 INITIATING DEVICES A.
Hard Wired Duress Switches: 1. Product: Sentrol 3040. 2. Product: USC HUB 2 Series 3. Substitutions: See State of Oregon General Conditions for Public Improvements Contracts.
B.
Wireless Duress Switches: 1. Product: Inovonics EN1235SF. 2. Single-button fixed position transmitter. 3. Wireless receiver: Inovonics EN7472DMP. 4. Substitutions: See State of Oregon General Conditions for Public Improvements Contracts.
2.04 SIGNAL DEVICES A.
Remote Annunciator: Provide supervised remote annunciator including audible and visual indication of intrusion by zone, and audible and visual indication of system trouble, in flush wall-mounted enclosure. Keypad will have a 32-character alphanumeric LCD, color backlit keyboard, self-test diagnostics, alert sounder, armed and AC LED. Keypad turns red in alarm condition. The keypad alphanumeric display shall provide complete prompt messages during all stages of operation and system programming and display all relevant operating and test data. The keypad shall provide an easy-to-read English text display. The text shall exactly match the text seen in all software reports, keypad displays, and central station reports. The keypad user interface shall be a simple-to-use, menu-driven help system that is completely user friendly. 1. Product: DMP 7060AN. 2. Substitutions: See State of Oregon General Conditions for Public Improvements Contracts.
PART 3 EXECUTION 3.01 INSTALLATION A.
Install in accordance with manufacturer's instructions.
B.
Wire in accordance with manufacturer's instructions for detection and signal circuit conductors. Refer to 26 05 05 for wiring installation requirements.
C.
Make conduit and wiring connections to door hardware devices furnished and installed under Section 08 71 00.
D.
Supervision for all field devices to be located at the end of line and not the head end panels.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 16 00 - 5
DURESS ALARM SYSTEM
E.
System shall be programmed with Alpha numeric door identifications for display on keypad and at central station.
F.
Facilities with existing central monitoring of the duress system: Coordinate compatibility of new system and associated dialer with the central monitoring. Provide verification that the monitoring company receives signals from each duress button in the system.
G.
Facilities with new central monitoring of the duress system: Obtain new monitoring company information from Owner. Coordinate compatibility of new system and associated dialer with the central monitoring company. Provide verification that the monitoring company receives signals from each duress button in the system.
3.02 FIELD QUALITY CONTROL A.
Perform field inspection and testing in accordance with State of Oregon General Conditions for Public Improvements Contracts.
B.
Test in accordance with NFPA 72.
3.03 MANUFACTURER SERVICES A.
Provide the services of the manufacturer's technical representative to prepare and start systems. 1. Include services of technician to supervise installation, adjustments, final connections, system testing, and Owner training.
3.04 CLOSEOUT ACTIVITIES A.
Demonstrate normal and abnormal modes of operation, and required responses to each.
B.
Provide the following instruction to designated Owner personnel: 1. Hands-On Instruction: On-site, using operational system. 2. Classroom Instruction: Owner furnished classroom, on-site or at other local facility.
C.
Provide 6 hours of training at each facility to designated Owner personnel covering issues for the topics below. Duration of individual training sessions as determined by Owner, not to exceed total number of required hours. 1. Administrative: Issues necessary for non-technical staff. 2. Basic/Detailed Operation: Issues necessary for attendant personnel, security officers. 3. Maintenance Technicians: Issues necessary for electrical technicians on programming, maintaining, repairing, and modifying.
D.
Furnish the services of instructors and teaching aids; have copies of operation and maintenance data available during instruction.
E.
Provide sign-in sheet and means of evaluation of trainees suitable to type of training given; report results to Owner.
3.05 PROGRAMING A.
Coordinate all programmable system functions with Owner prior to execution, including but not limited to: button ID's, zoning, access levels, logging, central station notification, authorization levels, etc. Provide all programing and startup services as required to satisfy the Owner.
3.06 MAINTENANCE A.
See State of Oregon General Conditions for Public Improvements Contracts for additional requirements relating to maintenance service.
B.
Provide a separate maintenance contract for specified maintenance service.
C.
Provide service and maintenance of intrusion detection system for one year from Date of Substantial Completion. END OF SECTION 28 16 00
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 16 00 - 6
DURESS ALARM SYSTEM
SECTION 28 23 00 VIDEO SURVEILLANCE PART 1 GENERAL 1.01 SYSTEM DESCRIPTION A.
A complete Video Camera System including Cameras, Power Supplies, NVR, video servers, client worksations, external storage devices, PoE (Power Over Ethernet) Network Switches, Category 6 Cabling, Category 6 Patch Panels, housings and mounts.
B.
NVR shall be located in existing server room; coordinate exact location with Owner.
C.
Monitors shall be LCD screens coordinate exact location with Owner.
1.02 REFERENCES A.
NFPA 70 - National Electrical Code.
B.
Products shall be listed by UL and shall bear the UL label.
C.
BICSI TDM Manual - Telecommunications Distribution Methods Manual; Building Industry Consulting Service International, Inc.; 2009.
D.
EIA-310 - Cabinets, Racks, Panels, and Associated Equipment; Electronic Industries Association; Revision D, 1992.
E.
TIA/EIA-568-B.1 -Commercial Building Telecommunications Cabling Standard - Part 1: General Requirements; Rev B, 2001; Addenda 1-7.
F.
TIA/EIA-568-B.2 - Commercial Building Telecommunications Cabling Standard - Part 2: Balanced Twisted Pair Cabling Components; Rev B, 2001; Addenda 1-11.
G.
TIA/EIA-568-B.3 -Commercial Building Telecommunications Cabling Standard - Part 3: Optical Fiber Cabling Components Standard, and Addendum 1 - Additional Transmission Performance Specifications for 50/125 um Optical Fiber Cables; Rev B, 2000; Addendum 1.
H.
TIA-569 -Commercial Building Standard for Telecommunications Pathways and Spaces; Rev B, 2004.
I.
TIA/EIA-606 - Administration Standard for the Telecommunications Infrastructure; Rev A, 2002.
J.
ANSI/J-STD-607 - Commercial Building Grounding (Earthing) and Bonding Requirements for Telecommunications; Rev A, 2002.
K.
UL 444 - Communications Cables; 2002.
L.
UL 497 - Standard for Protectors for Paired-Conductor Communications Circuits; 2001.
M. UL 514C - Standard for Nonmetallic Outlet Boxes, Flush-Device Boxes, and Covers; 1996. N.
UL 1581 - Reference Standard for Electrical Wires, Cables, and Flexible Cords; 2001.
O.
UL 1863 - Standard for Communications-Circuit Accessories; 2004.
1.03 SCOPE OF WORK A.
All NVR (Network Video Recorder), external storage devices, network switches, software, licenses, programming, cameras, housing, power supplies, mounts and any other required hardware to be provided by Contractor.
B.
120 volt power sources shall be provided by Contractor.
C.
All Category 6 Patch Panels & Category 6 Cabling to camera locations to be provided by Contractor.
1.04 SYSTEM COMPONENTS A.
NVR (Network Video Recorder).
B.
IP Video Cameras.
C.
External Storage Devices.
D.
PoE (Power Over Ethernet) Network Switches.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 23 00 - 1
VIDEO SURVEILLANCE
E.
Monitors.
F.
Video Review Software
G.
Racks & Mounts.
H.
Fiber Optic Cable.
I.
Category 6 Cabling.
J.
Category 6 Patch Panels and Patch Cords.
1.05 DESIGN/SHOP DRAWINGS A.
Submit design drawings with device layouts, cable routing, mounting and wiring details, including any required wiring for servers and client computers. See Section 26 05 05.
B.
Data sheets shall be provided on all equipment being provided.
C.
Minimum 1/16” scale drawings showing camera locations and associated wiring shall be provided.
D.
Details for camera mountings and housing shall be provided.
E.
Labeling and programming shall be as directed by Owner.
F.
Comprehensive list of all components and services provided.
1.06 RECORD DRAWINGS A.
Submit under provisions of Division 1.
B.
Record drawings of locations of initiating devices, signaling applications, end-of-line devices, conduit and cable routing. See Section 26 05 05.
C.
Programming device names and numbers.
1.07 QUALITY ASSURANCE A.
The Contractor shall be a local installation and service organization, currently recognized as a factory authorized representative by the manufacturer of the specified system.
B.
Installer Qualifications: A company having at least 3 years experience in the installation and testing of the type of system specified, and Supervisors and installers factory certified by manufacturers of products to be installed.
C.
At time of bid, the Contractor shall be licensed by the state or local jurisdiction to perform security work within the state. Contractors who have security licenses or permits pending shall not be considered acceptable for bidding on this project.
1.08 CATEGORY 6 CABLING WARRANTY A.
See Section 01 78 00 - Closeout Submittals, for additional warranty requirements.
B.
The Contractor shall provide a system warranty covering the installed cabling system against defects in workmanship, components, and performance, and follow-on support after project completion.
C.
The Contractor shall warrant the cabling system against defects in workmanship for a period of one year from the date of system acceptance. The warranty shall cover all labor and materials necessary to correct a failed portion of the system and to demonstrate performance within the original installation specifications after repairs are accomplished. This warranty shall be provided at no additional cost to the Owner.
1.09 DELIVERY, STORAGE, AND HANDLING A.
Store products in manufacturer's unopened packaging until ready for installation. In addition, cable must be stored in a location protected from vandalism and weather. If products stored outside, it must be covered with opaque plastic or canvas with provision for ventilation to prevent condensation and for protection from weather. If air temperature at product storage location will be below 40 degrees F, the cable to be moved to a heated (50 degrees F minimum) location.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 23 00 - 2
VIDEO SURVEILLANCE
B.
Keep stored products clean and dry. If necessary, products to be stored off site at the Contractor's expense.
PART 2 PRODUCTS 2.01 PRODUCTS FOR BENTON CO. COURTHOUSE A.
CAMERAS 1. 1 MP Fixed Dome a. Provide New Fixed Dome 1 megapixel IP Cameras: Axis P3354, Vicon, Honeywell, IQINVISION, Sony or approved equal. b. Image Sensor: Progressive Scan RGB CMOS 1/3” c. Lns: Varifocal with remote zoom and focus,P-Iris Contol, IR corrected, megapixel resolution. 1) 2.5-6 mm: 105°-49° view, F1.4, d. Automatically removable infrared-cut filter e. Min. Illumination: Color: 0.15 lux, F1.4, B/W: 0.03 lux, F1.4 f. Camera Angle Adjustment: Pan 360°, tilt 170°, rotation 340° g. Tamper-resistant polycarbonate casing h. Provide housings and mounts. i. Provide smoked domes.
B.
EXISTING VIDEO SERVERS 1. Add storage as needed to existing ONSSI video servers to provide a minimum of thirty (30) days of digital video storage for all new and existing cameras. Calculate storage based on 14 hours of room activity per day.
C.
POE (POWER OVER ETHERNET) NETWORK SWITCHES 1. Provide New 1000Mbps PoE Network Switches: Brocade FastIron WS Series or approved equal. 2. Provide PoE Switches that fully power all Network Ports on each Switch. 3. Locate Switches in Existing Telecom Rooms. Coordinate exact location with Owner. 4. Provide minimum of 20% spare network ports.
D.
CATEGORY 6 CABLING 1. TIA/EIA-568 Category 6 solid conductor unshielded twisted pair (UTP), 24 AWG, individually twisted pairs; covered with white jacket. AMP: Model #219560-2 or approved equal. 2. In locations other than in plenums, provide NFPA 70 type CMG general purpose, CMR riser-rated, or type CMP plenum-rated cable. 3. In plenums, provide NFPA 70 type CMP plenum-rated cable. 4. Provide sufficient Category 6 Patch Cords to connect all cameras. AMP: Model#1933121-4 or approved equal.
E.
CATEGORY 6 PATCH PANELS 1. Provide New Category 6 Patch Panels for Camera Cabling: Sized to fit EIA standard 19 inch wide equipment racks, 0.09 inch thick aluminum; cabling terminated on Type 110 insulation displacement connectors; printed circuit board interface. 2. Jacks: Non-keyed RJ-45, suitable for and complying with same standard as cable to be terminated; maximum 48 ports per standard width panel. 3. Capacity: Provide ports sufficient to connect all camera cables to be terminated plus 20 percent spare. 4. Labels: Factory installed laminated plastic nameplates above each port, numbered consecutively; comply with TIA/EIA-606-A using encoded identifiers. 5. Coordinate exact locations in racks with Owner. 6. AMP Model #13750114-2 or approved equal.
2.02 PRODUCTS FOR LINN CO. COURTHOUSE A.
CAMERAS 1. 1 MP Fixed Dome
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 23 00 - 3
VIDEO SURVEILLANCE
a. b. c. d. e. f. g. h. i.
Provide New Fixed Dome 1 megapixel IP Cameras: Axis P3354, Vicon, Honeywell, IQINVISION, Sony or approved equal. Image Sensor: Progressive Scan RGB CMOS 1/3” Lns: Varifocal with remote zoom and focus,P-Iris Contol, IR corrected, megapixel resolution. 1) 2.5-6 mm: 105°-49° view, F1.4, Automatically removable infrared-cut filter Min. Illumination: Color: 0.15 lux, F1.4, B/W: 0.03 lux, F1.4 Camera Angle Adjustment: Pan 360°, tilt 170°, rotation 340° Tamper-resistant polycarbonate casing Provide housings and mounts. Provide smoked domes.
B.
EXISTING NVR (NETWORK VIDEO RECORDER) 1. Add storage as needed to existing Digital Sentry DS RealVue Xpress to provide a minimum of thirty (30) days of digital video storage for all new and existing cameras. Calculate storage based on 14 hours of room activity per day.
C.
POE (POWER OVER ETHERNET) NETWORK SWITCHES 1. Provide New 1000Mbps PoE Network Switches: Brocade FastIron WS Series or approved equal. 2. Provide PoE Switches that fully power all Network Ports on each Switch. 3. Locate Switches in Existing Telecom Rooms. Coordinate exact location with Owner. 4. Provide minimum of 20% spare network ports.
D.
CATEGORY 6 CABLING 1. TIA/EIA-568 Category 6 solid conductor unshielded twisted pair (UTP), 24 AWG, individually twisted pairs; covered with white jacket. AMP: Model #219560-2 or approved equal. 2. In locations other than in plenums, provide NFPA 70 type CMG general purpose, CMR riser-rated, or type CMP plenum-rated cable. 3. In plenums, provide NFPA 70 type CMP plenum-rated cable. 4. Provide sufficient Category 6 Patch Cords to connect all cameras. AMP: Model#1933121-4 or approved equal.
E.
CATEGORY 6 PATCH PANELS 1. Provide New Category 6 Patch Panels for Camera Cabling: Sized to fit EIA standard 19 inch wide equipment racks, 0.09 inch thick aluminum; cabling terminated on Type 110 insulation displacement connectors; printed circuit board interface. 2. Jacks: Non-keyed RJ-45, suitable for and complying with same standard as cable to be terminated; maximum 48 ports per standard width panel. 3. Capacity: Provide ports sufficient to connect all camera cables to be terminated plus 20 percent spare. 4. Labels: Factory installed laminated plastic nameplates above each port, numbered consecutively; comply with TIA/EIA-606-A using encoded identifiers. 5. Coordinate exact locations in racks with Owner. 6. AMP Model #13750114-2 or approved equal.
2.03 PRODUCTS FOR MARION CO. ANNEX A.
CAMERAS 1. 1 MP Fixed Dome a. Provide New Fixed Dome 1 megapixel IP Cameras: Axis P3354, Vicon, Honeywell, IQINVISION, Sony or approved equal. b. Image Sensor: Progressive Scan RGB CMOS 1/3” c. Lns: Varifocal with remote zoom and focus,P-Iris Contol, IR corrected, megapixel resolution. 1) 2.5-6 mm: 105°-49° view, F1.4, d. Automatically removable infrared-cut filter
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 23 00 - 4
VIDEO SURVEILLANCE
e. f. g. h. i.
Min. Illumination: Color: 0.15 lux, F1.4, B/W: 0.03 lux, F1.4 Camera Angle Adjustment: Pan 360°, tilt 170°, rotation 340° Tamper-resistant polycarbonate casing Provide housings and mounts. Provide smoked domes.
B.
EXISTING NVR (NETWORK VIDEO RECORDER) 1. Add storage as needed to existing Bosch Divar 700 to provide a minimum of thirty (30) days of digital video storage for all new and existing cameras. Calculate storage based on 14 hours of room activity per day.
C.
POE (POWER OVER ETHERNET) NETWORK SWITCHES 1. Provide New 1000Mbps PoE Network Switches: Brocade FastIron WS Series or approved equal. 2. Provide PoE Switches that fully power all Network Ports on each Switch. 3. Locate Switches in Existing Telecom Rooms. Coordinate exact location with Owner. 4. Provide minimum of 20% spare network ports.
D.
CATEGORY 6 CABLING 1. TIA/EIA-568 Category 6 solid conductor unshielded twisted pair (UTP), 24 AWG, individually twisted pairs; covered with white jacket. AMP: Model #219560-2 or approved equal. 2. In locations other than in plenums, provide NFPA 70 type CMG general purpose, CMR riser-rated, or type CMP plenum-rated cable. 3. In plenums, provide NFPA 70 type CMP plenum-rated cable. 4. Provide sufficient Category 6 Patch Cords to connect all cameras. AMP: Model#1933121-4 or approved equal.
E.
CATEGORY 6 PATCH PANELS 1. Provide New Category 6 Patch Panels for Camera Cabling: Sized to fit EIA standard 19 inch wide equipment racks, 0.09 inch thick aluminum; cabling terminated on Type 110 insulation displacement connectors; printed circuit board interface. 2. Jacks: Non-keyed RJ-45, suitable for and complying with same standard as cable to be terminated; maximum 48 ports per standard width panel. 3. Capacity: Provide ports sufficient to connect all camera cables to be terminated plus 20 percent spare. 4. Labels: Factory installed laminated plastic nameplates above each port, numbered consecutively; comply with TIA/EIA-606-A using encoded identifiers. 5. Coordinate exact locations in racks with Owner. 6. AMP Model #13750114-2 or approved equal.
2.04 PRODUCTS FOR MARION CO. COURTHOUSE A.
CAMERAS 1. 1 MP Fixed Dome a. Provide New Fixed Dome 1 megapixel IP Cameras: Axis P3354, Vicon, Honeywell, IQINVISION, Sony or approved equal. b. Image Sensor: Progressive Scan RGB CMOS 1/3” c. Lns: Varifocal with remote zoom and focus,P-Iris Contol, IR corrected, megapixel resolution. 1) 2.5-6 mm: 105°-49° view, F1.4, d. Automatically removable infrared-cut filter e. Min. Illumination: Color: 0.15 lux, F1.4, B/W: 0.03 lux, F1.4 f. Camera Angle Adjustment: Pan 360°, tilt 170°, rotation 340° g. Tamper-resistant polycarbonate casing h. Provide housings and mounts. i. Provide smoked domes.
B.
EXISTING NVR's (NETWORK VIDEO RECORDER)
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 23 00 - 5
VIDEO SURVEILLANCE
1.
Add storage as needed to existing Pelco NVR's to provide a minimum of thirty (30) days of digital video storage for all new and existing cameras. Calculate storage based on 14 hours of room activity per day.
C.
POE (POWER OVER ETHERNET) NETWORK SWITCHES 1. Provide New 1000Mbps PoE Network Switches: Brocade FastIron WS Series or approved equal. 2. Provide PoE Switches that fully power all Network Ports on each Switch. 3. Locate Switches in Existing Telecom Rooms. Coordinate exact location with Owner. 4. Provide minimum of 20% spare network ports.
D.
CATEGORY 6 CABLING 1. TIA/EIA-568 Category 6 solid conductor unshielded twisted pair (UTP), 24 AWG, individually twisted pairs; covered with white jacket. AMP: Model #219560-2 or approved equal. 2. In locations other than in plenums, provide NFPA 70 type CMG general purpose, CMR riser-rated, or type CMP plenum-rated cable. 3. In plenums, provide NFPA 70 type CMP plenum-rated cable. 4. Provide sufficient Category 6 Patch Cords to connect all cameras. AMP: Model#1933121-4 or approved equal.
E.
CATEGORY 6 PATCH PANELS 1. Provide New Category 6 Patch Panels for Camera Cabling: Sized to fit EIA standard 19 inch wide equipment racks, 0.09 inch thick aluminum; cabling terminated on Type 110 insulation displacement connectors; printed circuit board interface. 2. Jacks: Non-keyed RJ-45, suitable for and complying with same standard as cable to be terminated; maximum 48 ports per standard width panel. 3. Capacity: Provide ports sufficient to connect all camera cables to be terminated plus 20 percent spare. 4. Labels: Factory installed laminated plastic nameplates above each port, numbered consecutively; comply with TIA/EIA-606-A using encoded identifiers. 5. Coordinate exact locations in racks with Owner. 6. AMP Model #13750114-2 or approved equal.
2.05 PRODUCTS FOR MARION CO. JUVENILE CENTER (NEW) A.
CAMERAS 1. 1 MP Fixed Dome a. Provide New Fixed Dome 1 megapixel IP Cameras: Axis P3354, Vicon, Honeywell, IQINVISION, Sony or approved equal. b. Image Sensor: Progressive Scan RGB CMOS 1/3” c. Lns: Varifocal with remote zoom and focus,P-Iris Contol, IR corrected, megapixel resolution. 1) 2.5-6 mm: 105°-49° view, F1.4, d. Automatically removable infrared-cut filter e. Min. Illumination: Color: 0.15 lux, F1.4, B/W: 0.03 lux, F1.4 f. Camera Angle Adjustment: Pan 360°, tilt 170°, rotation 340° g. Tamper-resistant polycarbonate casing h. Provide housings and mounts. i. Provide smoked domes.
B.
EXISTING NVR's (NETWORK VIDEO RECORDER) 1. Add storage as needed to existing Aventura NVR to provide a minimum of thirty (30) days of digital video storage for all new and existing cameras. Calculate storage based on 14 hours of room activity per day.
C.
POE (POWER OVER ETHERNET) NETWORK SWITCHES 1. Provide New 1000Mbps PoE Network Switches: Brocade FastIron WS Series or approved equal. 2. Provide PoE Switches that fully power all Network Ports on each Switch.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 23 00 - 6
VIDEO SURVEILLANCE
3. 4.
Locate Switches in Existing Telecom Rooms. Coordinate exact location with Owner. Provide minimum of 20% spare network ports.
D.
CATEGORY 6 CABLING 1. TIA/EIA-568 Category 6 solid conductor unshielded twisted pair (UTP), 24 AWG, individually twisted pairs; covered with white jacket. AMP: Model #219560-2 or approved equal. 2. In locations other than in plenums, provide NFPA 70 type CMG general purpose, CMR riser-rated, or type CMP plenum-rated cable. 3. In plenums, provide NFPA 70 type CMP plenum-rated cable. 4. Provide sufficient Category 6 Patch Cords to connect all cameras. AMP: Model#1933121-4 or approved equal.
E.
CATEGORY 6 PATCH PANELS 1. Provide New Category 6 Patch Panels for Camera Cabling: Sized to fit EIA standard 19 inch wide equipment racks, 0.09 inch thick aluminum; cabling terminated on Type 110 insulation displacement connectors; printed circuit board interface. 2. Jacks: Non-keyed RJ-45, suitable for and complying with same standard as cable to be terminated; maximum 48 ports per standard width panel. 3. Capacity: Provide ports sufficient to connect all camera cables to be terminated plus 20 percent spare. 4. Labels: Factory installed laminated plastic nameplates above each port, numbered consecutively; comply with TIA/EIA-606-A using encoded identifiers. 5. Coordinate exact locations in racks with Owner. 6. AMP Model #13750114-2 or approved equal.
2.06 PRODUCTS FOR MARION CO. JUVENILE CENTER (OLD) A.
CAMERAS 1. 1 MP Fixed Dome a. Provide New Fixed Dome 1 megapixel IP Cameras: Axis P3354, Vicon, Honeywell, IQINVISION, Sony or approved equal. b. Image Sensor: Progressive Scan RGB CMOS 1/3” c. Lns: Varifocal with remote zoom and focus,P-Iris Contol, IR corrected, megapixel resolution. 1) 2.5-6 mm: 105°-49° view, F1.4, d. Automatically removable infrared-cut filter e. Min. Illumination: Color: 0.15 lux, F1.4, B/W: 0.03 lux, F1.4 f. Camera Angle Adjustment: Pan 360°, tilt 170°, rotation 340° g. Tamper-resistant polycarbonate casing h. Provide housings and mounts. i. Provide smoked domes.
B.
NVR (NETWORK VIDEO RECORDER) 1. Install & Program Owner Provided Honeywell Fusion IV NVR: Coordinate exact location with Owner. 2. Provide Monitor at NVR location. 21" LCD, 1280 x 1024 minimum resolution. 3. Provide Remote Viewing Software. Install on client workstation. Coordinate with owner which workstation to install software on. 4. Record and store images with a minimum of 3.5 frames per second (fps) and 1 megapixel resolutions. Do not utilize compression schemes that compromise the stored video images to below these standards. 5. Provide a minimum of thirty (30) days of digital video storage for all cameras. Calculate storage based on 14 hours of room activity per day.
C.
POE (POWER OVER ETHERNET) NETWORK SWITCHES 1. Provide New 100/1000Mbps PoE Network Switches: Brocade FastIron WS Series, Comnet or approved equal. 2. Provide PoE Switches that fully power all Network Ports on each Switch.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 23 00 - 7
VIDEO SURVEILLANCE
3. 4.
Locate Switches in Existing Telecom Rooms. Coordinate exact location with Owner. Provide minimum of 20% spare network ports.
D.
CATEGORY 6 CABLING 1. TIA/EIA-568 Category 6 solid conductor unshielded twisted pair (UTP), 24 AWG, individually twisted pairs; covered with white jacket. AMP: Model #219560-2 or approved equal. 2. In locations other than in plenums, provide NFPA 70 type CMG general purpose, CMR riser-rated, or type CMP plenum-rated cable. 3. In plenums, provide NFPA 70 type CMP plenum-rated cable. 4. Provide sufficient Category 6 Patch Cords to connect all cameras. AMP: Model#1933121-4 or approved equal.
E.
CATEGORY 6 PATCH PANELS 1. Provide New Category 6 Patch Panels for Camera Cabling: Sized to fit EIA standard 19 inch wide equipment racks, 0.09 inch thick aluminum; cabling terminated on Type 110 insulation displacement connectors; printed circuit board interface. 2. Jacks: Non-keyed RJ-45, suitable for and complying with same standard as cable to be terminated; maximum 48 ports per standard width panel. 3. Capacity: Provide ports sufficient to connect all camera cables to be terminated plus 20 percent spare. 4. Labels: Factory installed laminated plastic nameplates above each port, numbered consecutively; comply with TIA/EIA-606-A using encoded identifiers. 5. Coordinate exact locations in racks with Owner. 6. AMP Model #13750114-2 or approved equal.
F.
4 CHANNEL DIGITAL VIDEO ENCODER 1. Provide New 4 Channel Digital Video Encoder: Axis 241QA or approved equal. 2. Min Video Resolution 4CIF 3. Motion JPEG and MPEG-4 Compression.
2.07 PRODUCTS FOR POLK CO. COURTHOUSE A.
CAMERAS 1. Provide New Fixed Dome Analog Cameras: TruVision 6100 Series or approved equal. 2. Provide housings and mounts. 3. Provide smoked domes. 4. Connect all cameras with Cat 6 UTP Cable.
B.
EXISTING DVR'S (DIGITAL VIDEO RECORDER) 1. Add storage as needed to existing GE DVR's to provide a minimum of thirty (30) days of digital video storage for all new and existing cameras. Calculate storage based on 14 hours of room activity per day.
C.
CATEGORY 6 CABLING 1. TIA/EIA-568 Category 6 solid conductor unshielded twisted pair (UTP), 24 AWG, individually twisted pairs; covered with white jacket. AMP: Model #219560-2 or approved equal. 2. In locations other than in plenums, provide NFPA 70 type CMG general purpose, CMR riser-rated, or type CMP plenum-rated cable. 3. In plenums, provide NFPA 70 type CMP plenum-rated cable. 4. Provide sufficient Category 6 Patch Cords to connect all cameras. AMP: Model#1933121-4 or approved equal.
2.08 PRODUCTS FOR YAMHILL CO. COURTHOUSE A.
CAMERAS 1. 1 MP Fixed Dome a. Provide New Fixed Dome 1 megapixel IP Cameras: Axis P3354, Vicon, Honeywell, IQINVISION, Sony or approved equal. b. Image Sensor: Progressive Scan RGB CMOS 1/3”
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 23 00 - 8
VIDEO SURVEILLANCE
c. d. e. f. g. h. i. j.
Lns: Varifocal with remote zoom and focus,P-Iris Contol, IR corrected, megapixel resolution. 1) 2.5-6 mm: 105°-49° view, F1.4, Automatically removable infrared-cut filter Min. Illumination: Color: 0.15 lux, F1.4, B/W: 0.03 lux, F1.4 Camera Angle Adjustment: Pan 360°, tilt 170°, rotation 340° Tamper-resistant polycarbonate casing Provide housings and mounts. Provide smoked domes. ONVIF Compliant
B.
EXISTING NVR's (NETWORK VIDEO RECORDER) 1. Add storage as needed to existing Bosch NVR's to provide a minimum of thirty (30) days of digital video storage for all new and existing cameras. Calculate storage based on 14 hours of room activity per day.
C.
POE (POWER OVER ETHERNET) NETWORK SWITCHES 1. Provide New 1000Mbps PoE Network Switches: Brocade FastIron WS Series or approved equal. 2. Provide PoE Switches that fully power all Network Ports on each Switch. 3. Locate Switches in Existing Telecom Rooms. Coordinate exact location with Owner. 4. Provide minimum of 20% spare network ports.
D.
CATEGORY 6 CABLING 1. TIA/EIA-568 Category 6 solid conductor unshielded twisted pair (UTP), 24 AWG, individually twisted pairs; covered with white jacket. AMP: Model #219560-2 or approved equal. 2. In locations other than in plenums, provide NFPA 70 type CMG general purpose, CMR riser-rated, or type CMP plenum-rated cable. 3. In plenums, provide NFPA 70 type CMP plenum-rated cable. 4. Provide sufficient Category 6 Patch Cords to connect all cameras. AMP: Model#1933121-4 or approved equal.
E.
CATEGORY 6 PATCH PANELS 1. Provide New Category 6 Patch Panels for Camera Cabling: Sized to fit EIA standard 19 inch wide equipment racks, 0.09 inch thick aluminum; cabling terminated on Type 110 insulation displacement connectors; printed circuit board interface. 2. Jacks: Non-keyed RJ-45, suitable for and complying with same standard as cable to be terminated; maximum 48 ports per standard width panel. 3. Capacity: Provide ports sufficient to connect all camera cables to be terminated plus 20 percent spare. 4. Labels: Factory installed laminated plastic nameplates above each port, numbered consecutively; comply with TIA/EIA-606-A using encoded identifiers. 5. Coordinate exact locations in racks with Owner. 6. AMP Model #13750114-2 or approved equal.
2.09 FIBER OPTIC CABLE PRODUCTS A.
Fiber Optic Cable: 1. 4-Strand multimode cable covered with an orange cable jacket. a. In locations other than plenums, provide NFPA 70 type OFNR nonconductive-riser-rated or type OFNP nonconductive-plenum-rated cable. b. In plenums, provide NFPA 70 type OFNP nonconductive-plenum-rated cable. c. Match cable diameter to existing onsite Fiber. d. Match existing fiber optic connector type. e. If there is no existing fiber use mutlimode 50/125 um fiber and LC connectors. f. Provide fiber optic patch panels and enclousures as needed. g. Manufacturer: Amp or approved equal.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 23 00 - 9
VIDEO SURVEILLANCE
PART 3 EXECUTION 3.01 INSTALLATION - DVR, NVR, EXTERNAL STORAGE DEVICES, & CAMERAS A.
Install in accordance with manufacturer's instructions.
B.
Provide manufacturer's field services.
C.
Include services of technician to supervise installation, adjustments, final connections, system testing, and training Owner's personnel.
3.02 INSTALLATION - CATEGORY 6 CABLING A.
Comply with latest editions and addenda of TIA/EIA-568, TIA/EIA-569, ANSI/J-STD-607, NFPA 70, and SYSTEM DESIGN as specified in PART 2.
B.
Cabling - General Requirements: 1. Do not install cable into conduits until conduit installation is complete. 2. Do not over-cinch or crush cables. 3. Do not exceed manufacturer's recommended cable pull tension and minimum bend radii. 4. When installing in conduit, use only lubricants approved by cable manufacturer and do not chafe or damage outer jacket. 5. Cable raceways shall not be filled greater than the NEC maximum fill for the particular raceway type. 6. Cables shall be installed in continuous lengths from origin to destination (no splices) unless specifically addressed in this document where cable splices are not allowed. 7. Cable shall be supported in conduit or cable tray where applicable. If a J-hook or trapeze system is used to support cable bundles, all horizontal cables shall be supported at a maximum of four-foot intervals. At no point shall cable(s) rest on acoustic ceiling grids or panels. 8. Cable shall be installed above fire-sprinkler and systems and shall not be attached to the system or any ancillary equipment or hardware. The cabling system and support hardware shall be installed so that it does not obscure any valves, fire alarm conduit, boxes, or other control devices. 9. Cables shall not be attached to ceiling grid or lighting support wires. Where light support for drop cable legs is required, the contractor shall install clips to support the cabling. 10. Any cable damaged or exceeding recommended installation parameters during installation shall be replaced by the contractor prior to final acceptance at no cost to the Owner.
C.
Copper Cabling: 1. All outlets shall be installed in the following manner: Cables shall be coiled in the in-wall or surface-mount boxes if adequate space is present to house the cable coil without exceeding the manufacturer's bend radius. In hollow wall installations where box-eliminators are used, excess wire can be stored in the wall. No more than 12 inches of slack shall be stored in an in-wall box, modular furniture raceway, or insulated walls. Excess slack may be neatly coiled and stored in the ceiling above each drop location when there is not enough space present in the outlet box to store slack cable. 2. Enough slack shall be stored in ceiling space for outlet to be relocated to furthest location in the room from the feeding IDF. 3. In addition, each cable type shall be terminated as indicated below: a. Cables shall be dressed and terminated to match existing cabling. b. Pair untwist at the termination shall not exceed 0.25 inch for Category 6 connecting hardware. c. The cable jacket shall be maintained as close as possible to the termination point. 4. Horizontal distribution cables shall be bundled in groups of not greater than 40 cables. Cable bundle quantities in excess of 40 cables may cause deformation of the bottom cables within the bundle. 5. UTP cable shall be installed so that there are no bends less than four times the outside diameter (4 x cable O.D.) at any point in the run. FTP cable shall be installed so that there
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 23 00 - 10
VIDEO SURVEILLANCE
are no bends less than 8 times the outside diameter (8 x cable O.D.) at any point in the run. D.
Field-Installed Labels: Comply with TIA/EIA-606-A using encoded identifiers. 1. Contractor shall submit for approval by Owner a proposed labeling system based on the above standard.
3.03 TESTING - CATEGORY 6 CABLING A.
Visual Inspection: 1. Inspect cable jackets for certification markings. 2. Inspect cable terminations for color coded labels of proper type. 3. Inspect outlet plates and patch panels for complete labels. 4. Inspect patch cords for complete labels. 5. Inspect cable termination to validate that cables were dressed and terminated in accordance with ANSI/TIA/EIA specifications for jacket removal and pair untwist, compliance with manufacturer's minimum bend radius, and that cable ends are dressed in a neat and orderly fashion.
B.
Testing - Copper Cabling and Associated Equipment: 1. Testing will be completed per Industry Standard for cable type to be tested. TIA/EIA-568-B.2-1 (Category 6), ISO/IEC 11801:2002 2nd Edition (classes D, E and F). 2. Category 6 Links: Perform tests for wire map, length, attenuation, NEXT, and propagation delay.
C.
Testing - Documentation: 1. The Contractor shall compile test results into forms that contain all applicable test data. All forms shall be neatly completed and legible when submitted. Hard copy optical traces shall be neatly and securely attached to the test results where indicated. Computer disks containing trace files will be submitted at the same time.
D.
Test Verification: 1. Upon receipt of the test documentation, The Owner reserves the right to perform spot testing of a representative sample of the cabling system to validate test results provided in the test document. Owner testing will use the same method employed by the Contractor, and minor variations will be allowed to account for differences in test equipment. If significant discrepancies are found, the Contractor will be notified for resolution.
E.
Final Inspection: 1. Upon completion of the project, The Owner's Technical Representative will perform a final inspection of the installed cabling system with the Contractor's Project Foreman. The final inspection will be performed to validate that all horizontal and backbone cables were installed as defined in the drawing package, and that the installation meets the aesthetic expectations of the Owner.
3.04 DEMONSTRATION A.
Provide systems demonstration and testing under provisions of this section, in addition to training to check and test operation of the systems in the presence of an Owner's representative.
B.
Demonstrate normal and abnormal modes of operation, and required response to each.
3.05 IN SERVICE TRAINING A.
Provide the following instruction to designated Owner personnel: 1. Hands-On Instruction: On-site, using operational system. 2. Classroom Instruction: Owner furnished classroom, on-site or at other local facility.
B.
Provide 6 hours of training at each facility to designated Owner personnel covering issues for the topics below. Duration of individual training sessions as determined by Owner, not to exceed total number of required hours. 1. Administrative: Issues necessary for non-technical staff. 2. Basic/Detailed Operation: Issues necessary for attendant personnel, security officers.
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 23 00 - 11
VIDEO SURVEILLANCE
3.
Maintenance Technicians: Issues necessary for electrical technicians on programming, maintaining, repairing, and modifying.
C.
Furnish the services of instructors and teaching aids; have copies of operation and maintenance data available during instruction.
D.
Provide sign-in sheet and means of evaluation of trainees suitable to type of training given; report results to Owner.
3.06 PROGRAMMING A.
Coordinate all programmable system functions with the Owner prior to execution, including but not limited to: time delay settings, zoning, authorization levels, update viewer with new cameras, etc. Provide all programming and start up services as required to satisfy the Owner. END OF SECTION
DAS Courts Sec Systems Reg 1 / HE-3206.6 28 23 00 - 12
VIDEO SURVEILLANCE
