shaftliner - USG Boral

---

TECHNICAL DATA

Shaftliner TECHNICAL DATA SHAFTLINER™

TM

BOR-2011 GECA 04-2011 v2 Panel Boards

PRODUCT TECHNICAL STATEMENT

Shaftliner

Shaftliner™ panels are specially manufactured Shaftliner™ panels are specially manufactured fire-stop TM fire-stop plasterboard panels, developed for use in plasterboard panels, developed for use in the Partiwall® Boral Plasterboard Cavity Shaft Wall systems to provide system. They are also suitable for for use in the USGvertical Boralducts and fire protection elevator shafts, other applications where installationfire is possible from Plasterboard Cavity Shaft Wall system to provide one side only. Shaftliner™ panel is 25mm thick, protection for elevator shafts where installation is possible 600mm wide bevelled edge fire-rated plasterboard ® ® , IntRwall and Shaft Wall systems. utilised in Partiwall from one side only.

USE

Shaftliner™ is certified by Good Environmental Choice Australia (GECA) and may contribute to Green Star points.

Shaftliner™ is suitable for use in all commercial and residential ADVANTAGES situations provided its specification and installation is in Shaftliner™ panels arethat specially manufactured • Fire resistance accordance with the USG Boral Partiwall • Lightweight construction Installation Manual – fire-stop plasterboard panels, developed for use in • Acoustic performance NZ & the USG Boral System + Manual.

• May contribute to green star points Boral Plasterboard Cavity Shaft Wall systems to provide It is suitable for installation on timber framed fire protection for elevator shafts, vertical ductswalls, andwhere the building design falls within the design scope of NZS3604, or PERFORMANCEisDETAILS other applications where installation possible from AS/NZS1170. one side only. Shaftliner™ FIRE panel is 25mm thick, • Achieves fire resistance of up to 4 hours when used in systems. is to befire-rated installed inplasterboard an existing building, the 600mmWhere wideShaftliner™ bevelled edge • Fire tested to achieve the least fire hazard Group Number for wall and ceiling materials defined by BCA BRANZ assessment installer must assure themselves that theasframing and existing ® ® utilised in Partiwall , IntRwallNo. FHand 3473. Shaft Wall systems.

building are suitable for the proposed building work.

ACOUSTIC Shaftliner™ is certified by Good Environmental Choice Shaftliner™, when used in an acoustic system can provide required CONDITIONS & LIMITATIONS levels of sound insulation to achieveStar specifiedpoints. acoustic ratings. Australia (GECA) and may contribute to Green

The specification of Shaftliner™ must be in accordance with STRUCTURAL USG Boral information. Shaftliner™ complies to the relevant deem-to-satisfy provisions of

ADVANTAGES It must be specified by an LBP, able to provide a design

BCA Specification C1.8 Structural Tests for Lightweight Construction.

• • • •

BOR-2011 GECA 04-2011 v2 Panel Boards

memorandum to the relevant Building Consent Authority Fire resistance www.usgboral.com/shaftliner (BCA),construction if RBW provisions apply. Lightweight Acoustic performance Installation must be undertaken by or supervised by an LBP (carpentry license). If RBW May contribute to green star pointsprovisions apply, this same LBP must complete the RBW memorandum.

Shaftliner™ Board should not be exposed to sustained temperaturesDETAILS exceeding 42°C or to excessive, repetitive or PERFORMANCE continuous moisture before, during or after installation. All FIRE sources of moisture should be eliminated immediately.

• Achieves fire resistance of up to 4 hours when used in systems. • Fire tested to achieve the least fire hazard Group Number for wall and ceiling materials as defined by BCA BRANZ assessment No. FH 3473.

BOARD SPECIFICATION NZBC COMPLIANCE Feature

Description

Shaftliner™ plasterboard complies with the following Thickness 25mm performance criteriaBevelled of the Edge Profiles edge NZ Building Code Sheet Size (width x length)

PERFORMANCE B1.3.1

600 x 3000mm, 600 x 3600mm [Please refer to Size & Availability Chart for more sizes]EVIDENCE CRITERIA Product availability: Certain products and sizes may only be available on order or in pack lots. In respect of building

Paper Colour B1.3.2

element

Blue/Grey

Manufactured in accordance with AS/ Mass 20.50 kg/m2 nominal NZS2588 B1.3.3 (a, b, c, f, j, I, o, r) Fire Hazard Properties

Group 1 – in accordance with BCA Panel performance Specification C1.10a Fire Hazard Properties – Floors, Walls and Ceilings.

Combustibility

Non Combustible material as defined in USG and Boral BCA Deem-to-Satisfy Provisions C1.12 have

VOC

Less than 0.5mg/m3 TVOC

B1.3.4 (a, b, c, e)

ASTM E72-80

a combined plasterboard manufacturing experience in excess of 145 years. During this time GECA Certified to GECA 04-2011 v2 B2.3.1(a), B2.3.2 USG Boral have supplied plasterboard – Panel Boards with Manufacture Manufacturedalong in Australia to the plasterboard wall and ceiling BOARD SPECIFICATION requirements systems of AS/NZS 2588:1998 for use within the residential and Gypsum plasterboard and in accordance commercial sectors. with AS/NZS ISO 9001:2008 – Quality

Feature

Description

management systems – Requirements

Material Group No 1-S

C3.4 (a) & (b)

Thickness

25mm assessment FH4435 BRANZ

Edge Profiles

Bevelled edge in accordance with Manufactured PBPD21 Aug 2014 AS/NZS2588

F2.3.1

Sheet Size (width x length)

600 x 3000mm, 600 x 3600mm [Please refer to Size & Availability Chart for more sizes] When installed Shaftliner™Product plasterboard contribute to availability:will Certain products and compliance with the following performance criteria of the sizes may only be available on order or in pack lots. NZ Building Code. Paper Colour

Blue/Grey

PERFORMANCE CRITERIA

EVIDENCE

B2.3.1(a), B2.3.2

In Service history

Mass

Fire Hazard Properties C6.2(a)

Combustibility G6.3.1

20.50 kg/m2 nominal

Group 1 – in accordance with BCA Specification C1.10a Fire Hazard CSIRO assessments Properties – Floors, Walls and Ceilings. CSIRO Measurement No TL429em (2004)

Non Combustible material as defined in

CSIRO Measurement No TL429qrs (2004) BCA Deem-to-Satisfy Provisions C1.12 CSIRO Measurement No TL469 (2006) 3

VOC

Less than 0.5mg/m TVOC

ACOUSTIC

GECA

Shaftliner™, when used in an acoustic system can provide required levels of sound insulation to achieve specified acoustic ratings.

Certified to GECA 04-2011 v2 – Panel Boards

Manufacture

Manufactured in Australia to the requirements of AS/NZS 2588:1998 Gypsum plasterboard and in accordance with AS/NZS ISO 9001:2008 – Quality management systems – Requirements

STRUCTURAL Shaftliner™ complies to the relevant deem-to-satisfy provisions of BCA Specification C1.8 Structural Tests for Lightweight Construction.

www.usgboral.com/shaftliner 1www.usgboral.com

PBPD21 Aug 2014 JUNE 2015

|

PTS209/3 1 OCTOBER 2017 DONN® SCREWFIX™ SUSPENSION SYSTEM

» PRODUCT TECHNICAL STATEMENT DESCRIPTION OF SHAFTLINER™

STORAGE & TRANSPORTATION Shaftliner™ like all plasterboards is vulnerable to in transit damage. It should be transported and stored horizontally. Ensure that it is covered, to avoid the possibility of exposure to moisture.

BOARD SPECIFICATION FEATURE

DESCRIPTION

Thickness

25mm

Edge Profiles

Bevelled edge

Sheet Size (width x length)

600 x 3000mm, 600 x 3600mm Product availability: Certain products and sizes may only be available on order or in pack lots.

Paper Colour

Grey

Mass

20.50 kg/m2 nominal

VOC

Less than 0.5mg/m TVOC

GECA

Certified to GECA 04-2011 v2 – Panel Boards

Manufacture

Manufactured in Australia to the requirements of AS/NZS 2588:1998 Gypsum plasterboard and in accordance with AS/NZS ISO 9001:2008 – Quality management systems – Requirements

3

SUSTAINABILITY Shaftliner™ has been manufactured using 100% recycled liner paper. Independently tested for VOC .

QUALITY ASSURANCE Shaftliner™ is manufactured in Australia. These manufacturing sites are ISO9001:2008 accredited. Certificate details are SAI Global Cert No. QEC0400. This certification dates from 1992.

WARRANTY For details of the USG Boral warranty refer www.usgboral.com

PERFORMANCE DETAILS

DURABILITY STATEMENT

Fire

This statement is in relation to Clause B2 Durability of the New Zealand Building Code (NZBC). USG Boral Plasterboard products and systems are designed for internal use and when installed in accordance with the installation instructions detailed within the relevant Technical Installation literature they are fully compliant with the NZBC.

Shaftliner™ is a non-combustible building product. Shaftliner™ achieves a material group 1-S depending on finished coating applied (BRANZ Assessment FH4435). Shaftliner™ achieves fire resistance ratings depending on the fire rated systems application.

Acoustic Shaftliner™ may be used in an acoustic system to provide required levels of sound insulation to achieve specified acoustic ratings.

INSTALLATION

FURTHER INFORMATION Contact USG Boral TecASSIST on 0800 USGBORAL (0800 874-267) or online at www.usgboral.com

For sales enquiries: Auckland (09) 270-2595 Wellington (05) 560-4528 Christchurch (03) 365-4245

Shaftliner™ must be installed in accordance with the USG Boral Partiwall Installation Manual - NZ or USG Boral Plasterboard Installation Manual – NZ.

MAINTENANCE Shaftliner™ does not require maintenance but USG Boral recommends that a visual check of the board be undertaken as part of normal maintenance. In the event that damage is apparent to the Shaftliner™ board then it must be removed and replaced in accordance with the USG Boral Partiwall Installation Manual – NZ & the USG Boral System + Manual.

2 www.usgboral.com

JUNE 2015

|

DONN® SCREWFIX™ SUSPENSION SYSTEM