Installation Instructions

---

QUINCE™

2

Installation Instructions

BLUE STRIPE

RED STRIPE

Turn off hot and cold water supplies before beginning.

4433.350

SINGLE LEVER SEMI-PROFESSIONAL KITCHEN FAUCET

5

MAKE WATER SUPPLY CONNECTIONS

Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply (Marked with a Red Stripe) to Hot and right supply (Marked with Blue Stripe) to Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten.

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

COLD

Recommended Tools

3

M915628-YYY0A SPOUT SPRING

Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).

HOT

M964177-YYY0A SPRAY ARM

Place SEALS (8) into CARTRIDGE PORTS (6a). Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING SCREWS (5) alternately.

Certified to comply with ANSI A112.18.1M

M965242 REV. 1.4

4433.350

Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).

Important: If SUPPLY HOSES (1, 2) are too long, loop as illustrated to avoid kinking.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

MODEL NUMBER

Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3). Unthread the ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5).

Faucet supplies are 27-1/2" long from faucet base.

1

SINGLE LEVER SEMI-PROFESSIONAL KITCHEN FAUCET

If faucet drips, operate HANDLE several times from "off" to "on." Do not apply excessive force. Clogged CARTRIDGE outlets or inlets may cause reduced flow. To clean, first turn off water supply then:

2

Note: If additional supply length is required, installer must purchase additional parts separately.

QUINCE™

SERVICE

Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE SCREW (1) and install INDEX BUTTON (2).

TEST INSTALLED FAUCET

3 8

6a 1

6

Move HANDLE (1) into "off" position. Phillips Screwdriver

1

Channel Locks

Adjustable Wrench

INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON

Unthread SPRAY END (2) from HOSE END (3).

Plumbers' Putty or Caulking

CAUTION

Turn off hot and cold water supplies before beginning.

5

Operate HANDLE (1) on and off, hot and cold to flush water lines thoroughly. Replace SPRAY END (2).

(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1). Make certain the SEAL (2) is properly seated in recess of faucet body. Insert SUPPLY HOSES (3) and SHANK (4) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface. Follow mounting instructions below to secure faucet to mounting surface.

6

Check all drain connections for leaks.

2 B

3 4

Assemble RUBBER WASHER (4), METAL WASHER (6) and threaded LOCKNUT (7) onto SHANK (3) from underside of sink or mounting surface. Hand tighten LOCKNUT (7).

Loosen the SPOUT SET SCREW (1) with a 3mm Hex wrench. Rotate the SPOUT (3) side to side while pulling upward to remove SPOUT (3) from faucet body.

1

REMOVE

SPRAY OPERATION

Check that SPOUT (3) rotates freely and does not leak at the swivel point.

4

REMOVE

A951470-0070A CARTRIDGE

INSTALL

A911836-0070A SEAL

2

M907306-YYY0A ESCUTCHEON CAP

4

M962806-YYY0A ESCUTCHEON AND PUTTY PLATE

3

PUTTY

3

5 6 7 8

M962146-0070A MOUNTING KIT

3

5 6 7 8

2

M964176-YYY0A HANDLE KIT

M918506-0070A CARTRIDGE SCREWS

3mm HEX WRENCH

2

1

M903757-YYY0A SPOUT PIPE

M917147-YYY0A SPOUT SET SCREW

1

Press and hold PAUSE BUTTON (3) to temporarily stop flow from SPRAY (2). Release PAUSE BUTTON (3) to resume flow from SPRAY (2).

2

M950322-YYY0A PULL-DOWN SPRAY

Replace the defective parts, grease O-RINGS then push SPOUT (3) back into position. Tighten SET SCREW (1).

With FAUCET on press TOGGLE BUTTON (1) on SPRAY (2) to switch from stream to spray.

Use a screwdriver to tighten SCREWS (8) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening the screws slightly each time until all are snug to ensure even pressure.

M964289-0020A SPRAY HOSE AND SEALS

If SPOUT (3) leaks at swivel point the O-RINGS (2) need to be replaced. To remove SPOUT (3):

3

A

4

SERVICE

Move HANDLE (1) to "off" position.

(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Make certain the SEAL (2) is properly seated in recess of faucet body. Insert supply HOSES (3) and SHANK (4) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.

M914600-0070A SPRAY ARM BUSHING

7

Turn on water supplies and check connections for leaks.

M964175-0070A SPOUT BUSHING & O-RING KIT

2

M962294-0070A BUTTON AND SCREW KIT Replace the YYY with Appropriate finish code CHROME STAINLESS STEEL OIL RUBBED BRONZE

002 075 224

STREAM (AERATOR)

7

1

CARE INSTRUCTIONS:

HOT LINE FOR HELP

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

SPRAY HOT & COLD SUPPLIES M965242 REV. 1.4

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.

M965242 REV. 1.4

M965242 REV. 1.4

For toll-free information and answers to your questions, call: 1-800-442-1902 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-1200 Product names listed herein are trademarks of American Standard Inc. © AS America, Inc. 2012