Technical Bulletin No. 20Page 1 of 7


[PDF]Technical Bulletin No. 20Page 1 of 7 - Rackcdn.comc3366550.r50.cf0.rackcdn.com/pdfs/techbul20.pdfCachedfilter tank already be filled, please refe...

0 downloads 193 Views 466KB Size

Nature 2 (Copper/Silver Purifier)

Technical Bulletin No.

20

Page 1 of 7

20.1 Parts List Nature 2 Purification System (packaged in control board box) (4) Purifier cartridges (2) End caps

20.2 Description The Nature 2 pool purifier consists of four purifying cartridges and two end caps (see Fig.1). Two of the cartridges and both end caps are needed for assembly. The remaining two purifying cartridges are to be used as replacements. NOTE: It is best to install the Nature 2 purifier into your filter canister before filling with water. Should your filter tank already be filled, please refer to the “Operations & Maintenance” video to review how to drain the filter. Figure 1 – Purifier Cartridges & End caps Figure 2 - Tabs

20.3 Installation Instructions 1) Lay an end cap on a flat surface and snap only two (2) of the cartridges into it, so that the tabs are pointing up (Fig. 2). 2) Snap the other end cap on top. 3) Remove the lid of the Predator filter tank following the same procedures you’d use for a filter change (see Technical Bulletin #18). Gently remove the black center core and filter cartridge from the filter tank. 4) Place the assembled Nature 2 purifier into the middle of the filter tank. Install the black center core and filter cartridge over the Nature 2 assembly. Reassemble the filter. Note: Some of the materials supplied in the box of Nature 2 cartridges and also later in this technical bulletin are directly from the Nature 2’s manufacturer. Their recommended start-up procedures were not written specifically with the Endless Pool in mind and differ somewhat from what is recommended above and what is listed in Tech Bulletin #26. We recommend that you follow the installation and start-up procedures listed here and in Tech Bulletin #26.

20.4 Replacement Instructions Your Nature 2 purifier needs to be replaced every 6 months. Jot a reminder in your Endless Pool testing log or use the small stickers included in this box to note the necessary change date. Replacement cartridges (after the first set) can be purchased from Endless Pools or from a local pool store. 1) Disassemble the filter as detailed in the “Operations and Maintenance” video. Remember to drain the water from the canister before unfastening the lock ring assembly. Clean or replace the filter cartridge, as needed. 2) Remove the Nature 2 purifier from inside the black center core. 3) Remove the two end caps from both sides of the purifier cartridges. Discard the old cartridges. 4) Reassemble the purifier using the two end caps and the new purifier cartridges as described in steps 1 and 2 of the above “Installation Instructions.”

Endless Pools Inc.

5/3/04

Nature 2 (Copper/Silver Purifier)

Technical Bulletin No.

20

Page 2 of 7

Endless Pools Inc.

5/3/04

Nature 2 (Copper/Silver Purifier)

Technical Bulletin No.

20

Page 3 of 7

Endless Pools Inc.

5/3/04

Nature 2 (Copper/Silver Purifier)

Technical Bulletin No.

20

Page 4 of 7

Endless Pools Inc.

5/3/04

Nature 2 (Copper/Silver Purifier)

Technical Bulletin No.

20

Page 5 of 7

Endless Pools Inc.

5/3/04

Nature 2 (Copper/Silver Purifier)

Technical Bulletin No.

20

Page 6 of 7

Endless Pools Inc.

5/3/04

Nature 2 (Copper/Silver Purifier)

Technical Bulletin No.

20

Page 7 of 7

Endless Pools Inc.

5/3/04